Sequencers
-
Product
Triple Output DC Power Supply, 60V/3A (2x) & 5V/3A; 375W
U8032A
DC Power Supply
Keysight now extends its range of basic DC power supplies to offer 375watt power range, making it an ideal power source alternative in electronics manufacturing, research and development as well as the education sector. The U8032A, basic DC power supply, is a manual triple-output power supply with sequencing capability. With this function, users can generate output sequences with minimal programming skills. Each power supply is also built with excellent load regulation and clean output noise for continued stability. With these and many other features, you get a solid and reliable triple-output power supply at an unsurpassed performance.
-
Product
PXIe-4143, 4-Channel, ±24 V, 150 mA Precision PXI Source Measure Unit
782431-01
Source Measure Unit
PXIe, 4-Channel, ±24 V, 150 mA Precision PXI Source Measure Unit - The PXIe-4143 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation and each channel has integrated remote (4-wire) sensing for accurate measurements. The fast sample rate of the PXIe-4143 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4143 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
Serial AC Power Sequencer
90-200-001
-
Each power outlet can be programmed to switched on in sequence with a specific timing delay. The delay can be staggered to ensure that order dependent systems - like PXI - can be switched on and off in an orderly way with just one operation. A staggered start up also limits the inrush current associated with the powering up of equipment, including earth current inrush, placing less stress on cabling and leakage breakers. Power on or off instructions can be initiated from either the front panel switch or via the serial interface.
-
Product
PXIe-4138, 60 V, 3 A System PXI Source Measure Unit
782856-01
Source Measure Unit
±60 V, 3 A System PXI Source Measure Unit—The PXIe‑4138 system source measure unit (SMU) delivers high power, precision, and speed. It is ideal for a broad range of applications including manufacturing test; board-level test; lab characterization with devices such as integrated circuits (ICs), power management integrated circuits (PMICs), and radio frequency integrated circuits (RFICs); and discrete devices including LEDs and optical transceivers. The PXIe‑4138 features 4-quadrant operation. The PXIe‑4138 is a hardware-timed instrument with a high-speed sequencing engine for synchronizing acquisitions between multiple SMUs. The module supports direct DMA streaming between the host PC and SMU, so you can stream large waveforms and measurement data at the full update rate and sample rate of the instrument.
-
Product
Circuit Testing
CUBE,POLARITY (GT-10)
-
*Circuit verifying polarity cube troubleshoots 120 V AC grounded outlets*Light sequence indicates correct/incorrect wiring
-
Product
High Performance 50 MHz Dynamic Digital I/O PXI Subsystem
GX5960 Series
Digital I/O
The GX5960 digital subsystem represents the highest level of performance available for PXI-based digital instrumentation and features high performance pin electronics and a timing generator / sequencer in a compact, 6U PXI form factor. The GX5960 series consists of the GX5961 clock generator board with 16 driver / sensor channels and the GX5964 driver / sensor board which supports 32 bi-directional I/O channels. Up to 528 digital I/O channels can be supported by the GX5960 digital subsystem. Each digital channel features a wide drive / sense voltage range of -14 V to +26 V (maximum swing of 24 volts) which can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and a load value (with commutation voltage level) – offering the user complete flexibility when creating test programs and fixtures for multiple UUTs. In addition, each channel offers a parametric measurement unit (PMU) for DC measurements.
-
Product
Multifunctional testers
MI 3102 BT EurotestXE
-
MI 3102 BT EurotestXE is a multifunctional measuring instrument which performs a complete set of installation safety tests according to IEC/EN 61557. It supports AUTO SEQUENCE® testing of the TN, TT and IT earthing systems. ISFL measurements and the IMD tests can be performed. Besides, the MI 3102 BT EurotestXE enables on-line voltage monitoring, phase sequence testing, earth resistance measurement, illuminance measurement and TRMS current measurement. EurotestXE is equipped with integrated characteristics of fuses and RCDs for PASS / FAIL evaluation of test results.
-
Product
Combination Measurement Workstation
WS500
-
The WS500 is a combination measurement workstation that incorporates several different measurement types that can be included in a single characterization sequence.
-
Product
Rad Hard Power Sequencing
-
Renesas' radiation hardened quad power supply sequencers are designed to drive point-of load (POL) regulators that power high performance FPGAs and complex, multi-rail power systems.
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5150 Series
Digital I/O
The GX5150 Series are high speed, 6U PXI, sequenced digital I/O instruments. The GX5150 master controller has 32 bits of I/O channels that supports test rates of up to 50 MHz and a vector depth of up to 128 Mb per pin. The GX5151 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5150. The GX5150 can control up to 15 GX5151 boards using the same timing and sequencer.
-
Product
Motorized Force & Torque Measurement Test Stands
-
Mark-10 offers a wide and unique range of motorized force measurement and torque measurement test stands. Motorized stands offer a significant advantage over manual test stands by providing constant test speed. Some models can be programmed for advanced test sequences to accommodate demanding applications. All motorized test stands carry the CE mark. A test stand is an integral part of a testing system, typically also comprising a force gauge or torque gauge, grips, software, and accessories.
-
Product
Weapon Control System Test Set
MS 1102
-
- Provides serviceability checks on armament system- Portable instrument- Check the Bomb release sequence, practice bomb release sequence, rocket release sequence, fuzing, and jettison of aircraft stores- Helps to identify faults of conventional armament- Microprocessor based design
-
Product
Professional Thermal Camera
FLIR T560
-
Troubleshoot hot spots, find hidden faults, and confirm repairs quickly with the ergonomic, high-resolution FLIR T560. This 640 × 480 (307,200 pixel) thermal imaging camera has a bright 4" LCD and a 180° rotating lens platform, so you can easily and comfortably diagnose electrical or mechanical issues, even in hard-to-reach areas. Advanced on-camera measurement tools such as 1-Touch Level/Span, plus laser-assisted autofocus, ensure you’ll record accurate temperature measurements every time. With on-board FLIR Inspection Route mode, you can download and run survey plans to your camera from FLIR Thermal Studio Pro (with FLIR Route Creator plugin). Together these systems will help you record temperature data and imagery in a logical sequence for faster troubleshooting and repair. The T560 also features FLIR Ignite for automatic uploading of images directly from the camera to the cloud for easy, secure storage and sharing. The purchase of a T560 camera includes a 3-month subscription to FLIR Thermal Studio Pro and FLIR Route Creator.
-
Product
Automation Tool for the CMW Platform
CMWrun
-
The R&S®CMW is the leading multistandard UE testing platform used by network operators, test houses, handset vendors and chipset manufacturers worldwide. R&S®CMWrun automation software meets all requirements for executing remote control test sequences on the R&S®CMW for wireless equipment in R&D, quality assurance, production and service. The intuitive graphical user interface of the R&S®CMWrun sequencer software allows easy and straightforward test sequence configuration. No programming and code compilation are needed. At the end of the test, an easy-to-read test report of the limits, test results and verdict is generated.
-
Product
Hipot Tester
STM/L
-
SafeTest Manufacturing/Luminaire (STM/L) can be used as a simple manual electrical safety tester or with varying degrees of automatic test sequencing.
-
Product
Sequence Creation Software for Power Supplies and Electronic Loads
Wavy Series
-
WAVY is sequence creation software that supports the power supplies and electronic loads from KIKUSUI Electronics Corp.
-
Product
Multifunction Tester
COMBI521
-
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Universal Counter (225MHz - 9GHz)
S43131
-
S43131 series universal counter is the high-precision frequency and time measuring instrument developed by Saluki Technology. It adopts the high-performance single chip microcomputer as the core to conduct function control, survey time sequence control, data processing and result display. Adopt the countdown counting technique and digital interpolation technique to realize high-precision measurement within the whole range.S43131 series universal counter has stable performance, complete function, wide measurement range, high sensitivity, large dynamic range, high precision, small volume and convenient and reliable use. It has wide application in industrial production, scientific research and measurement and other fields, and is the ideal upgraded and renewed product of the traditional electronic counter.
-
Product
Railway Wheel Number Identification Complex
-
Our automated scanning system is based on smart 3D cameras SICK Ruler E 600. Information about the wheel profile from the camera via a high-speed Gigabit Ethernet interface is sent to a dedicated computer for processing, detecting and recognizing the alphanumeric sequence applied to a specific section of the wheel. Synchronization with the rotation system is carried out by means of a high-precision encoder, with the conveyor system - via the Profibus DP interface. The complex is designed to scan wheels of various standard sizes and allows with a high resolution (tenths of a millimeter), without readjustment, to read numbers from wheels at a radius of 100 to 600 mm in 45 seconds.
-
Product
High-Voltage Test Hood with Integrated Hipot
LX-HVE900IS
-
Large test room with a hood made of sturdy, highly insulating and transparent plastic, which guarantees a clear view of the test item and the signal lamp during the test. The system is operated on the test device. Alternatively, test sequences stored on an integrated computer can be started automatically by closing the hood. The test sequence can be fully followed on the monitor.
-
Product
Electric Insulating Oil Tester
PortaTest
-
Portatesters are easy to use. Based on the test standard, you select the corresponding test sequence. Then, the required test probe and the electrode gap for the selected test standard is displayed. The setting gauge, included in the scope of delivery, facilitates the adjustment of the electrode gap. Afterwards you fill the insulating oil in the test vessel and close the test chamber.
-
Product
BERT Measurement Solutions
-
Bit error rate testers (BERTs) are usually the initial step for communications testing. These instruments generate digital test patterns, typically pseudorandom binary sequences (PRBSs), that drive devices under test (DUTs). Following the transmission of the signal through the link, the receiver in the BERT captures the signal. This setup can be used for multiple testing purposes, such as to evaluate the performance of a transmitter, a receiver, or an optical link.
-
Product
DC Bias and RF Stimulus Control Module
Quantum SMART Fixture
-
Accel-RF Corporation, the world leader in turnkey RF automated reliability test instruments, has "unplugged" the industry-leading RF SMART Fixture from their automated test platform and made it available for benchtop test. The NEW Quantum SMART Fixture is a programmable self-contained DC bias and RF stimulus control module capable of synchronizing sequenced independent pulsed-bias and pulsed-RF signals to a DUT or remote fixture. The signals are controlled from a user interface compatible with Accel-RF's LIFETEST software. The Quantum SMART fixture is capable of "active" temperature control and monitoring of a remote DUT through embedded firmware in the microprocessor
-
Product
Photosynthesis System
LCpro-SD
-
The LCpro-SD offers laboratory grade experimental performance in a truly portable device. Featuring ADC's highly accurate miniaturized infrared gas analyzer, the LCpro-SD is, at 4.5kg or 10lbs., less than half the weight and half the size of conventional systems offering full environmental control. Ideal for A/Ci curves, and A/Q curves, measuring step sequences are full programmable.
-
Product
Circuit Testing
Tester, Circuit GFI
-
*Use to troubleshoot 120 VAC grounded outlets and test GFCI receptacles*Light sequence indicates correct/incorrect wiring*Lifetime Limited Warranty
-
Product
8 SE Or 4 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-8-4
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
Oil Breakdown Voltage Tester
DTA 100 C
-
Insulating oil testing with the BAUR DTA 100 C. The BAUR DTA 100 C oil tester is designed for continuous operation in the laboratory and is characterised by the combination of extraordinary features. As a high-performance device with a test voltage up to 100 kV, with clear breakdown detection and absolutely reliable measurement results even across several measurement sequences, the BAUR DTA 100 C is the leading testing device for users in the electricity and other industries and in testing institutes.
-
Product
TMS Test Management Software
LX TMS
-
To diagnose and analyze electronic components and devices, various tests are required in development, production and service. Equipped with all the necessary standard functions, the test sequencer developed by LXinstuments meets all criteria for a successful and smooth test process. The test item ( DUT ) is examined under various operating conditions for its properties, function and usability. Typical areas of application can be found where the usual complexity of test sequences has to be processed. The test sequencer is therefore suitable for small and medium-sized systems where special functions of other sequencers are not required. The free, cross-platform, open source developer platform .NET serves as a starting point. The integrated WPF (Windows Presentation Foundation) framework ensures a user-friendly program interface.
-
Product
PI Series Precision Line Infrared Camera
-
Experiencing real-time thermal images with a frame rate of up to 128 Hz, capturing and saving fast measurement results as snap-shots or video sequences or, thanks to the excellent thermal sensitivity, indicating even smallest changes in temperature – to only name a few of the many advantages.
-
Product
Toolset for NI TestStand
TS+
-
MESULOG TS + includes new configurable TestStand steps that simplify product characterization and validation, while reducing the time and cost of developing test sequences. With TS + , you can easily create advanced loop structures, save and replay datasets, display data dynamically, and include screenshots in your reports.
