-
Product
Hot Wire Ignition Tester
-
The HWI test indicates a materials resistance to ignition when exposed to abnormally high temperatures resulting from a component failure such as a conductor carrying far more than its rated current. HWI performance is expressed as the mean number of seconds required to ignite a specimen when wrapped with an energized non-chrome resistive wire that dissipates a specified level of energy.
-
Product
SAR Testing
-
RF transmitters used in close proximity to the human body must be evaluated against human Exposure standards which set basic restrictions for the Specific Absorption Rate (SAR) of RF energy by any part of the human body. This may include two-way radios, cellular phones, smartphones, spread spectrum, Bluetooth devices, wireless EFTPOS terminals and WLAN devices used in PDA/notebook/laptop/tablet computers. In Australia and Europe, virtually all devices exceeding the power threshold of 20mW (13dBm) and used in close proximity to the human body must comply with SAR requirements. There is no such blanket exemption in the USA and Canada where each product must be assessed against frequency/power level criteria.
-
Product
NEXT GENERATION RADIO PLATFORM
INTEGRA S
-
Integra S is an unbelievably light, energy efficient carrier-grade system that exemplifies an outstanding return on smart engineering - the synergy of high competence in radio electronics and materials science. Slip-fit design allows integration with existing high performance antenna systems or integration with 2+0 aggregation setups for up to 954 Mbps Full Duplex capacity without header compression. Gigabit Power over Ethernet (PoE) port defies simple installation, while dual SFP slots allow for fiber optic installation – giving the user ultimate flexibility in cable design.
-
Product
RF Coaxial Load
-
RF Lambda’s coaxial loads are used to terminate RF signal chain to provide a good 50ohm match and dissipate any excess RF energy. They are available in a variety of power levels and offer low VSWR.
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
Astronomy Solutions
-
For more than 40 years, Thales has delivered high accuracy optics for ground-based Astronomy all around the world. These optics range from single, but challenging, unmounted optical components up to fully integrated opto-mechanical systems. Our design heritage and past experience in this field cover the design, manufacture and AIT activities of many optics and sub-assemblies used in Telescope instrumentation, such as focal plane assemblies as well as the direct production of telescope mirrors themselves. Several major achievements of Thales ground-based Astronomy products were the Optical wide field corrector for the Dark Energy Survey (lien), the Reference Body for future Deformable Secondary Mirror of the VLT (lien) and different challenging spectrograph optics (Collimator and Cameras) for different Observatories (lien). One advantage Thales has with this activity is that most part of the manufacturing steps involved (i.e. opto-mechanical design, milling/grinding, lightening, polishing and coating) are directly under our control in our own facility. Our current capabilities for the production of optics for ground-based Astronomy are from a few centimeters size up to 2 meters. Thanks to the continuous efforts in R& D and investments into new production machines, Thales is now ready for future industrial challenges including the optical production of some key elements of the E-ELT, GMT and TMT programs.
-
Product
Power Energy & Power Quality Analysers
-
Designed for test and maintenance teams working in industrial or administrative buildings can be used to obtain a snapshot of the main features characterizing the quality of the electrical network.
-
Product
Power Analyzers
-
At PCE Instruments you will find a power quality analyzer to measure the power in W, kWh or to analyze and measure harmonics. This power analyzer is a multi-function power analyzer device that measure precisely direct current, alternating current, AC-voltage, DC-voltage the intensity of DC or AC, phase rotation and idle, apparent and effective power. The reading of AC power is considered the real value and has a maximum range of 6000 Watts. While a reading is being taken, the polarity changes automatically, if negative values are taken then a minus sign will appear on the device display.Nowadays, power quality analyzers have many features such as, insulated current input, measurement of harmonics, AC and DC current measurement, AC and DC voltage measurement, frequency measurement, phase rotation measurement and idle, apparent and effective power measurement. All this data can also be logged and analyzed with the delivered PC-Software. Power analyzers of the type PCE PA 6000 can determine the energy in single-phase systems.Power quality analyzers of type PCE-GPA 62 allow the energy measurement in symmetrically loaded three-phase systems. Power analyzers of type PCE-PA 8000, PCE-360 and PCE-830 support professional power and energy measurements in single and three-phase systems.Apart from being used as energy-measuring devices, power analyzers like the PCE-830 can also be used for network analysis and the determination of harmonics and phase rotation. On our website you will find other power analyzers used in the field of electronics.
-
Product
Temperature Data Logger
DL001
-
Record temperature in a wide range of applications including HVAC testing and balancing, transportation, and energy management with the Model DL001 Temperature Data Logger. Temperature logger has an on-board thermistor and an external sensor channel for remote temperature measurements
-
Product
Computerized 8 Channels Battery Analyzer
BTS8-WA
-
BTS8-WA is a precision eight channels battery test system for measuring battery capacity at 0.002mA - 1mA up to 5V.. This systems the best tool to study new generation energy storage materials and rechargeable battery.
-
Product
Differential Temperature Controller
-
Normal temperature controller acts on one single input and tries and maintain that temperature at a pre programmed constant level. A differential temperature controller as the name suggest, takes two temperature inputs and tries to maintain the difference between these two temperatures as constant. This is widely used in today’s innovation Solar Energy Systems to provide maximum operating efficiency and flexibility. It automatically maintains the difference e.g., In case of self powered solar box furnace or in case of a solar water collector. By automatically switching on a fan or a pump the temperatures can be equalized.
-
Product
High-Speed Impact Testing Machines
HITS-X Series
-
With the increasing demand for safety and reliability, evaluation of the dynamic strength (impact properties) of materials and parts is becoming more and more important. This machine can obtain data, such as the maximum test force, energy, and displacement, up to a maximum velocity of 72 km/h (20 m/s). A tensile load type (HITS-TX) and a punching type (HITS-PX) are available.
-
Product
Specific Absorption Rate (SAR) Testing
-
SAR limits are there to protect all of us from wireless devices that exceed the transmit Radio Frequency (RF) threshold. SAR stands for Specific Absorption Rate. It's a measure of the rate at which energy is absorbed by your body when you are exposed to an RF electromagnetic field. In some countries, the SAR test result figure has to be displayed at the point of sale. To have a presence in these markets, your products must meet strict SAR regulations.
-
Product
Battery Formation and Testing System
BFS 2000
-
BENNING Elektrotechnik und Elektronik GmbH
For many decades now, BENNING has designed and manufactured charge/discharge converters for the battery industry. These converters are used in both the production and testing processes involved in battery manufacturing and for series-testing of batteries. BENNING's BFS battery production and testing system provides a solution which makes it easier to control and monitor production and test processes which saves both time and energy. When used in power stations and rail applications (mobile version), it can be used to test and maintain a wide range of battery types.
-
Product
Three-Phase Transformer Winding Resistance Meters
TWA Standard Series
-
When it comes to winding resistance measurement on three-phase power transformers and autotransformers, TWA Standard series offers some of the most technically advanced instruments with LCD display in the market. Both models are capable of testing six transformer windings with a one-time cable connection, as well as three-phase automatic transformer demagnetization. The stored magnetic energy is safely automatically discharged at the end of the test. The built-in tap changer control unit enables automated test mode, where the instrument operates the tap changer without operator input and records winding resistance results based on pre-selected stabilization criteria. This option makes the operator’s job significantly easier.Both models can output test currents from 5 mA to 25 A DC for the purpose of winding resistance measurement. TWA40D has a special test mode for checking the synchronization of on-load tap changers with three phases simultaneously tested in parallel, in which the total test current can rise to up to 40 A DC.TWA40D has additional advantages when it comes to non-intrusive tap changer analysis. The unique DVtest method enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, simultaneously with the measurement of tap changer motor current which helps with the detection of motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or on three phases simultaneously. It can also be performed as an additional test simultaneously with the winding resistance test in all tap positions.An additional unique advantage of TWA40D is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer (connected in a YN configuration). This can significantly shorten the total testing time – for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.The test leads for TWA three-phase transformer winding ohmmeters are interchangeable with the TRT turns ratio testers, which means that both sets of tests can be performed with a single test lead connection to the power transformer terminals.
-
Product
Universal Radiometer
Rm-3700
-
The Rm-3700 Single Channel Universal Radiometer, when used with the correct probe, can measure cw and average power (in Watts), as well as the energy (in Joules) of individual pulses up to 2 kHz, over a wide range of intensities and wavelengths. A high-speed Rs-232 computer interface, full statistical analysis of pulse sets, battery/AC power, and audible tuning are just some of the standard features. This tremendous versatility makes it the ideal instrument for research labs, universities, hospitals, and other facilities with multiple light sources and applications.
-
Product
Calorimeter
CWD2005 Device Series
-
The CWD2005 device series (Calorimetry, Wobbe-Index und Specific Density) comprises versions of combustion calorimeters for direct and continuous determination of gas quality from the following measurands and operands:*Wobbe-lndex*Specific density*Heating and combustion values*Combustion Air Requirement (CARI) and air requirement, with integrated gas analysis*Energy quantity, with expanded system EMS2005.
-
Product
Power Semiconductor Device
IGBT/SIC
-
Hitachi High Voltage IGBTs have been corresponding to a wide range of applications such as railway applications and various power conveters, leading companies for domestic and overseas adopt them, since they were adopted as a railway application in 1992. Will continue to contribute to the developing energy society by pursuing more easy-to-use, high-performance and high -quality products with leading-edge research and development.
-
Product
Octal Digital Multi Channel Analyzer
V1782
-
The V1782 is the new CAEN Octal 32k digital MCA. Designed for high energy resolution semiconductor detector is perfectly suited for those application in which the number of input channels start becoming relevant such as when segmented HPGe, Clovers and silicon detectors are involved.The V1782 provides four steps of software selectable coarse gain and two possible jumper selectable dynamical ranges (0.2-0.4-0.8-1.6 Vpp and 1-2-4-8 Vpp).It is also compatible with Transitor reset preamplifier thanks to the jumper selectable 10 us AC coupling.
-
-
Product
Single Board Computers
ITX-P-C444
-
The ITX-P-C444 is an industrial Pico-ITX single board computer (SBC) with NXP’s i.MX8M application processor and packed with dual Ethernet, industrial I/O, and expansion options. The processor supports industry-leading video processing along with an M4 microcontroller for real-time subsystems making it an ideal fit for industrial IoT applications requiring performance in harsh conditions such as digital signage, industrial automation, energy management, building automation, among others.
-
Product
AC Power Measurement and Logging
WattNode® Logger for LonWorks®
-
Continental Control Systems LLC
The WattNode Logger is a kilowatt hour (kWh) energy meter that communicates on a LonWorks network, and can log 24,000+ measurement records in non-volatile memory. The WattNode Logger measures 1, 2, or 3 phases with voltages from 120 to 600 volts alternating current (Vac) and 5 to 6,000 amps in delta (phase to phase) and wye (phase to neutral) configurations.
-
Product
Battery Simulator
G5.BAS
-
The G5.BAS series is bidirectional regenerative. It was developed specifically for the simulation of energy storage devices and batteries and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3.
-
Product
High Voltage Film Capacitors
-
High Voltage Pulse Capacitors, High Voltage Energy Discharge Capacitors, High Voltage Filter Capacitors and Customized High Voltage Capacitors
-
Product
Solar Radiation Detector PCE-SPM 1
-
PCE-SPM 1 is a photovoltaic (PV) light meter used to measure solar radiation, solar energy or solar power. The meter's easy-to-read 4-digit LCD screen clearly displays Ptot in W/m² or BTU/(ft² x h), while the device's auto data memory stores up to 43,000 data sets.
-
Product
CryoPulse
-
Metis Instruments & Equipment NV
Measurements in up to 50 T environments. Cryogenic measurement environment with temperature control from 4K up to room temperature. Modular architecture with easy upgrades to higher energies & higher peak fields. Fast sample exchange possible. Large set of measuring probes for various applications
-
Product
Luminaire Testing
-
Product Safety Consulting Inc.
With the emergence of LED technologies, being part of the renewed energy scene requires knowledge of how to design products to meet consumer needs while passing even more stringent safety testing than ever before. Staying on top of the new testing requirements, from local and global standpoints, is what we do. Standards generally are not clear; they leave room for interpretation and often present constraints to product design. At PSC, we offer solutions to non-compliance rather than simply reporting a pass/no-pass statement. And, we communicate with straightforward explanations of safety issues that often arise during the testing process. Our expert product testing team understands what you need to do to achieve compliance. Failing at the testing stage only costs you valuable time and money. It allows the competition to beat you to the sale and takes resources away from future growth.
-
Product
Plug in Meters
-
make accurately measuring the power (watts) and energy (kilowatt-hours) consumption of 117vac plug in appliances a snap!
-
Product
Phase Sequence Meters
-
Phase sequence meter is used for detecting the sequence of the supply in three-phase electric circuits. Since the direction of rotation of three phase electric motors can be changed by changing the phase sequence of supply. And also the correct operation of measuring instruments like 3 phase energy meter and automatic control of devices also depend on the phase sequence. Different types of phase sequence testers are available in today’s market like contact or non contact, static or rotating, etc., in a wide range of voltage or power ratings.
-
Product
Meter Test System
MTS-50
-
Kongter Test & Measurement Co., Limited
This meter test equipment features state-of-art designing with high accuracy. It is composed of high accurate (class 0.05% or 0.1%) standard reference meter and power source (up to 50A). This system is particularly designed with modular structure for calibration and test of different single phase/3 phase electronic/inductive active and reactive energy meters.
