Filter Results By:
Products
Applications
Manufacturers
-
product
Interface
RCNIC-A2PAU4
Abaco Systems' RCNIC-A2PAU4 is a high performance 4-lane PCI Express interface for monitoring, generating or analyzing full-bandwidth AFDX/ARINC 664 protocol traffic. Our exclusive pipeline architecture maximizes packet throughput using parallel controllers and efficient DMA transfers, thereby avoiding the bottlenecks of CPU-based interface solutions.
-
product
1MP OV10633 Custom Lens Camera Module
e-CAM1M_CU10630_MOD
e-CAM1M_CU10630_MOD is a High Dynamic Range (HDR), Wide Dynamic Range (WDR), custom lens camera module targeted for surveillance and security applications. This HDR camera module based on the OV10633 sensor from OmniVision is e-con’s first Wide Dynamic Range (WDR) camera module that can stream 1280x720p video at 30fps over its 8-bit digital video parallel interface. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice.
-
product
Hyperspectral Cameras with USB3 Vision
xiSpec
*Smallest Hyperspectral camera - Compact, lightweight with only 26.4 x 26.4 x 31 mm, 32 grams (1)*Cost efficient - Excellent value and price through utilizing new imec hyperspectral imaging technology*Cool economy - Low power consumption with 1.6 Watt, minimal heat dissipation, ideal for UAV / UAS*All-around support - USB 3.0 support for Windows 7 and 10, macOS, Linux, ARM*Powerful potential - Highest spatial and spectral resolution, possible with 5Gb/s interface*Optimized - 2048 parallel, "on-chip" integrated spectroscopes with 100 points of spectral resolution each*AIA standard - USB3 Vision standard compliant*Industry standard interface - Compatible with USB 3.0 SuperSpeed specification*Fastest Hyperspectral camera - High speed, high frame rate: based on 170 fps at 2.2 Mpix resolution*Connectivity and Synchronization - Programmable optoisolated input and output, 3 status LEDs*Easy deployment - Range of accessories and wide hardware and software integration*Highly Customizable - Variety of sensor options, which can be further adjusted to match requirements*Interoperability increase - Continuous embrace of new software and hardware partners
-
product
PMC-BiFIFO
The parallel Input and Output channels are highly programmable and fully independent. The standard interface offers Data, Clock and Strobe. The 32 RS485 channels are programmable as input or output allowing for a variety of implementations. The programmable output rates and RS422/485 compatability will interface to a multitude of systems.
-
product
LCR Meter, Hand Held, 100 kHz, 2 kH, 20000 µF, 0.2 Gohm
72-10465
The 72-10465 from Tenma is a LCR meter in orange and grey colour. It features an easy to read dual LCD (40mm x 63mm) display measurement of 19999/1999 (main/auxiliary). It also has series and parallel measurement modes which can be used to select quality factor, loss factor, phase location angle and equivalent resistance of measure articles. Intelligent detection and five different test frequencies enable accurate readings for all sizes of capacitors and inductors. The user can also access the stored data on a PC with the included USB connection and interface software. The compact size and case make this unit far more portable than a benchtop meter.
-
product
Frequency and Phase Agile 120 MHz Signal Generator.
DDS8p
The DDS8p generates cosine, sine and ACMOS/TTL output signals. The frequency is programmable in 1µHz steps from 100Hz to 120MHz. The phase is 14-bit programmable. The DDS8p is controlled by a binary parallel interface that allows frequency and phase changes as fast as 600 nanoseconds. It is accurate to 1ppm and requires 5 VDC power.
-
product
Serial Parallel Interface
Model 2303
* 2303 Board provides 40 high-power TTL I/O lines that can sink 23 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual Serial headers support conections with baud rate switch inputs or to a Serial Flat Ribon Cable Assembly. * Optional Relay Driver board drives 24-40 relays. * 114732 Board has the DIN connector on circuit side for use with the X3DVR Relay Driver Board or for piggyback mounting.* All other specifications are the same as listed above for the 2303.
-
product
Serial And Parallel Port For PCIe
DTA-2142
Serial and parallel interfaces for ASI and SD-SDI, supporting multiple electrical standards including M-LVDS and LVTTL. Clock rates up to 108MHz are supported.
-
product
PMC Compatible SpaceWire Interface
PMC-SpaceWire
Utilize SpaceWire to communicate with the European Space Agency and NASA equipment utilizing the ECSS-E-50-12A specification. SpaceWire is configured using routers to create a heirarchical point-to-point system with high speed parallel paths. PMC SpaceWire implements SpaceWire in a convenient PMC format. With PMC you can install the adapter into PCI [PCIBPMC], cPCI [cPCI2PMC], or processor board pmc slots. The SpaceWire specification calls for LVDS signaling and a specific 9 pin micro-D connector. You can connect the PMC-SpaceWire to other SpaceWire compliant devices without electrical interface issues.
-
product
ICT Software: Interactive Developmetn Encironment ICT ICE & ICT Sequencer
ICT IDE and Sequencer
The ICT software consists of two parts, the interactive development environment ICT IDE and the ICT sequencer. The IDE provides a graphical user interface for convenient creation and testing of these test sequences and allows:- Convenient management of hardware resources via topology editor- Support of several independent embedded testers for parallel test execution- Editing sequences in a text or table editor- Error highlighting during sequencing- Sequence execution (also single step) directly on a selected DUT- Debugging (single step)- Loop execution via sequences, or single steps- Optimization function with regard to waiting time and integration with Shmoo plot- detailed results output within tables as well as various results diagrams- Pin-Finder function to support adapter wiring- Automatic test program generation is available via Aster Testway
-
product
4000W to 50,000W - Single Output
ALE-Rack Mount Series
*Compact, lightweight design*Simple parallel operation for higher power*Worldwide input voltages/frequencies*Fully adjustable output voltage*Full remote control interface*Safety agency approvals
-
product
5 Mega Pixel Parallel Camera Module
e-CAM52A_5640_MOD
The e-CAM52A_5640_MOD is a Parallel Camera Module from e-con systems featuring Omnivision OV5640 image sensor. Any processor system like I.MX6, OMAP4430, OMAP4460, OMAP35x, AM37x, DM37x that has a Parallel interface can integrate the e-CAM52A_5640_MOD.
-
product
6U VPX FPGA Cards
Curtiss-Wright Defense Solutions
FPGAs have revolutionized the way digital signal processing (DSP) subsystems are configured. With a large number of gates, hardware multipliers, and high-speed serial interfaces, FPGAs enable sophisticated applications, including radar, signal intelligence, and image processing, which rely on repetitive processing that can be expressed in highly parallel form. FPGAs perform exceptionally well in FFTs, pulse compression, filters, and digital up/down converters.
-
product
USB Modular Source Measure Unit
U2722A
The U2722A USB Modular Source Measure Unit is a 3-channel 20V/120mA that can operate in a 4-quadrant operation. The channels could be connected in series or in parallel to achieve up to 60 V/360 mA. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity allowing users to set up and configure their tests swiftly with its plug and play feature.
-
product
Electronic Ballast Automatic Test Equipment
ATE-1
Test series connection, parallel connection and series/parallel connections of the electronic ballast (about 15 kinds of connections), available for various electronic ballast. • With a precise resistance box, tube is substituted for the resistance, can act as many as 6 tubes. Resistance value: 1-4095Ω adjustable. • Measure input parameters (vrms, irms, w, pf, harmonics, etc), output parameters (on-circuit voltage, lamp voltage, filament voltage, lamp current, lamp power, oscillatory frequency), can also test the ballast efficiency, abnormity protection, and power symmetry of partial rectifier effect and etc. • Program controlled AC power source to guarantee the smart choice of input voltage and the frequency. • Equipped with 17 inch LCD controlled machine, specially designed A/D combined with special CPU, has the two left and right testing interfaces to achieve stability of data and high- speed testing. • We can make the special-designed product for you and promise to upgrade the software for free.
-
product
32 Channel Multi-Purpose DIOS/TAP Modules/Interfaces for Spare JT 2148 QuadPOD Transceiver Slot
JT 2149/MPV eMPV
The JT 2149/MPV and the JT 2149/eMPV are a 32 channel multi purpose DIOS/TAP pod modules/interfaces that can be plugged into any spare JT 2148 QuadPOD transceiver slot. The DIOS channels of these units I/O interface pods enable increased fault coverage and thus improved diagnostic resolution during boundary-scan testing. The principal difference between the two versions is the use of an extended case on the eMPV that allows standard 0.1″ connections to be used to access ths TAP and static IO signals (see tab below)- on the standard /MPV unit these signals are available at the front face 0.05″ connector. The units are fully supported by JTAG Technologies’ development tools. Additional DIOS modules can be serially connected if more parallel access points are required.
-
product
Mezzanine System
3560
ECM P/N 3560 provides four independent I2C channels. For ease of development a PCA9564 interface IC converts parallel data to I2C serial communication. Additionally an LTC1694 I2C accelerator IC decreases the rise time of the passively pulled up I2C bus allowing for greater capacitive loading or higher bus speeds. Each channel is comprised of SCL, SDA and two Grounds.
-
product
Fixed Mount Strobes
Our fixed mount stroboscopes are designed for installation in applications requiring continuous stroboscopic visual inspection. The MVS is available with xenon or LED light output with adjustable pulse width and focal distance for optimized target illumination. Connect your existing trigger signal or the optional Frequency Controller with LCD. Connect multiple units together in parallel for applications with wide illumination area requirements. Use the optional Audio Interface Box and microphone to create stunning audio driven visual effects.
-
product
96/48/24-CH Opto-22 Compatible Digital I/O PCI Cards
PCI-7296/7248/7224
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
product
Self/Fast Boot use on SKY Boards
Each of these loads occur internally to each SKYbolt board at the speed of the internal SKYbolt busses; we are not limited to the speed of the VME bus, the host VME interface or the disk. These program loads also occur in parallel so the startup time is independent of the number of SKY boards in the system.
-
product
Ethernet To Parallel Digital Interfaces
ICS's 8063 Ethernet Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications.
-
product
0 Hz/DC to 14 GHz, Single-Pole, Four-Throw MEMS Switch With Integrated Driver
ADGM1304
The ADGM1304 is a wideband, single-pole, four-throw (SP4T) switch, fabricated using Analog Devices, Inc., microelectro-mechanical system (MEMS) switch technology. This technology enables a small, wide bandwidth, highly linear, low insertion loss switch that is operational down to 0 Hz/dc, making it an ideal switching solution for a wide range of RF applications. An integrated control chip generates the high voltage necessary to electrostatically actuate the switch via a complementary metal-oxide semiconductor (CMOS)-/low voltage transistor-transistor logic (LVTTL)-compatible parallel interface. All four switches are independently controllable. The ADGM1304 is packaged in a 24-lead, 5 mm × 4 mm × 0.95 mm lead frame chip-scale package (LFCSP).
-
product
Serial To Digital Interface MiniBox™
ICS's 2363 Serial Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
product
NTDS I/O Analyzer
The NTDS I/O Analyzer provides insight and visibility, enabling users to quickly and efficiently analyze timing relationships, message protocols, throughput, and data integrity on all types of NTDS interfaces. It is capable of monitoring any combination of NTDS Parallel Type A, B, C, H and NTDS Serial Type D, E channels as defined in the MIL-STD-1397 revision B and C specifications regardless of NTDS mode. The channels are connected to existing NTDS cabling with NTDS tap boxes and extract ongoing communication. Each word of NTDS information received is time-stamped with a 125 nanosecond resolution clock ensuring highly accurate timing measurements. Data collected is stored locally for analysis and can be transmitted to external equipment enabling remote troubleshooting, event reconstruction, or time-critical feedback on system performance.
-
product
Serial To Digital Interface MiniBox™
ICS's 2363 Serial Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
product
PXI 16 Bank 5 Channel 1 Pole Multiplexer
40-616-021-16/5/1
The 40-616 16-Bank, 5-Channel, 1-Pole Multiplexer Module forms part of the System 40 PXI Programmable Switching system. The Module consists of 16 electrically isolated banks of multiplexers controlled by a PXI/ PCI interface. Each bank is a 1 to 5 multiplexer and operates with break-before-make action when a new channel is selected. Any Individual multiplexer bank can have a channel set by itself, alternatively, multiple banks can have channels selected simultaneously. The module is suitable for cascading in applications that require large multiplexer systems, it is also suitable for test systems that require the switching of a large number of signals in parallel.
-
product
Serial Parallel Interface
Model 2313
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
-
product
100 MHz 32-CH High-Speed Digital I/O Card
PCIe-7360
ADLINK's PCIe-7360 is a high-speed digital I/O board with 32-CH bi-directional parallel I/O lines. Data rate up to 400 MB/s is available through the x4 PCI Express® interface. Clock rate can support up to 100 MHz internal clock or 200 MHz external clock, ideally suiting applications of high-speed and large-scale digital data acquisition or exchange, such as digital image capture, video playback and IC testing.
-
product
Efficient All-In-One Test Solution for Low-Cost IoT Devices
KT RFCT 2400
The low price point creates a cost effective means for testing wireless communication units, while generating a favorable cost to performance ratio.The calibrated RF test system has a small footprint, integrating seamlessly into test system infrastructures via a single Ethernet connection. GPIOs control the DUT and peripherals. The test system enables communication interfaces like SPI, I2C, UART and CAN. Simple Go/No-Go tests can be performed in parallel. The KT-RFCT 2400A features a 70 MHz to 6 GHz frequency range and includes non-signaling and signaling connections. Bluetooth signaling standards are supported up to 4.1 as well as BT-LE. WIFI signaling standards supported are a, b, g, n and ac.The KT-RFCT 2400A is the perfect test system for a wide range of applications, such as Bluetooth, Infotainment, Keyless Entry, Tire Pressure Measurement, GPS and WIFI.
-
product
192 Channel Power Supply
HDPMU
Today cost efficiency is more important than ever. Many manufacturers are working on maximizing multi-site testing. Often maximization can’t be done because of limited tester resources. Salland’s HDPMU gives you up to 192 additional independent parametric measurement units (PMU) channels on a single board. Our solution will increase parallel testing without the need for creating complex device interface board (DIB). It can be used for continuity, functional or parametric tests or simply for device setup or loading. Full integration with the Teradyne IG-XL™ Software, easy set-up and high parallel measurement capability will reduce test costs significantly.
