-
Product
Pressure Insensitive Mass Flow Module
Criterion D500
-
This leading-edge pressure insensitive mass flow module is installed with differential pressure detection and a piezo actuator valve.
-
Product
Differential Pressure Transmitter
636D
-
The Series 636D Differential Pressure Transmitter can be used for measuring pressures of liquids, gases & vapors. All available ranges have an excellent 0.5% F.S. accuracy with a 4-20 mA Output standard or optional 1-5 VDC output.
-
Product
Diaphragm Operated Pressure Switch
1000E
-
Extremely rugged construction provides excellent reliability in chemical, petroleum and industrial plants. Bellville spring movement permits mounting of control in any position and helps prevent contact chatter. new design also provides high overpressure protection. Available with standard weatherproof housing to meet NEMA-1 through 4X and NEMA-13, JIC.
-
Product
Tire Pressure Gauge
-
ZhangZhou Weihua Electronic co.,ltd
Is a pressure gauge used to measure the pressure of tires on a vehicle. Since tires are rated for specific loads at certain pressure, it is important to keep the pressure of the tire at the optimal amount.
-
Product
Fluid Pressure Booster
-
Nordson EFD Fluid Pressure Booster is designed to help move thick materials from a tank or cartridge to an EFD precision valve by boosting dispense pressure up to 100 bar.
-
Product
Explosion-Proof Differential Pressure Switch, 10 inH2O Sensitivity
H3
-
Explosion-proof, heavy duty, industrial unit has patented and unique new design which provides sensitivity to differential pressures as low as 10 inches of water (254 mm w.c.), yet handles total pressure of 1500 psi (103 bar). Unlike common differential pressure switches that use a piston-type motion transfer, the Series H3 utilizes a rotary motion transfer shaft that prevents a change in total pressure from causing a setpoint shift.
-
Product
SURFACE PROFILE GAGES
-
Steel is often abrasive blast cleaned or otherwise roughened prior to painting. The peak-to-valley height of the resultant surface profile is an important factor in the performance of applied protective coatings. Low profile may reduce coating bond strength (adhesion). Too high and the peaks may receive insufficient coverage and possibly rust prematurely. The costly application of more coating may be required if the profile is too high. For these reasons, surface profile should be measured prior to coating application to ensure that it meets contract specifications.
-
Product
Fuel Pressure Testers
-
• Developed with input from technicians on adaptor selection for 7.3 L, 6.7 L, 6.4 L and 6.0 L Ford®Power Stroke®engines• 0 100 PSI gauge and hose assembly• Low-pressure diesel-fuel delivery testing (lift pump)• Correct fuel delivery and dynamic fuel pressure are crucial to having a properly running engine• Helps prevent a lean condition that may cause burning of injectors or scorched cylinders• Convenient protective slide-lid case that will fit in a 4" drawer for easy tool access• Technical Support: 1-866-713-6007
-
Product
Pressure / Manometers
-
Sper Scientific handheld manometers, vacuum, and pressure meters are ideal for measuring low differential pressure in clean rooms, test and balance, medical equipment, HVAC, pneumatic systems and computer peripherals.
-
Product
Automated Gage Measurement System
AGMS
System
Our Automated Gage Measurement System for Sand Screen (AGMS) provides accurate and repeatable optical measurements for all wire-wrapped gaps along the full screenlength. This inspection machine enables oil field sand screen manufacturers to meet the measurement requirements of API Spec 19S1 and ISO 17824:2009.
-
Product
Pressure Regulators & Outlet Points
-
WITT offers a wide range of gas pressure regulators and gas outlet points for almost all technical gases, pressure and flow requirements. Our product portfolio includes spring-loaded pressure regulators, dome-loaded pressure regulators and complete pressure regulating stations as well as outlet points and system solutions for safe and reliable gas supply.
-
Product
Economical Pressure Switch
P88G
-
The P88G Economical Pressure switches are typically used in applications where reliable switch control supersedes accuracy of set point.Controlling on and off functions for fans and pumps where one may need a wide differential to prevent over-cycling is an ideal application use for the P88G.
-
Product
Pressure Fittings
-
AMETEK Sensors, Test & Calibration
Our CPF Fittings & Hose are a new line of quick-test pressure fittings for calibration & test applications - designed with an emphasis on safety. Crystal Pressure Fittings (CPF) perform up to 10 000 psi / 1000 bar, and feature a safety weep hole to alert you before you accidently disconnect from a pressurized system. It can also be used as a bleed point. CPF fittings seals two ways: use fingers for an o-ring seal or use a wrench for a metal to metal cone seal (good to -40°C).
-
Product
Pressure testing solutions
-
Pressure testing involves applying stored energy to an assembly of parts, in order to verify its strength, its integrity and/or its functionality. Pressure Testing generally uses the application of a test fluid (liquid or gas) into a volume and the fluid is then pressurised to exert pressure forces onto the test object that can be measured.
-
Product
Fixed Range Pressure Transmitter
636
-
The Series 636 Pressure Transmitter is a low cost, fixed range, stainless steel transmitter with ±0.30% accuracy. It is designed to continuously measure pressure for years in even the toughest environmental and media conditions
-
Product
Pressure, Strain And Shock Data Loggers
-
Dataloggers for pressure, bridge input for strain or load measurement and also tri-axial shock dataloggers with built in accelerometers.
-
Product
High-Temperature Strain Gages
ZWH-, ZWN-, & ZWP-Series
-
ZWH-, ZWN-, and ZWP-Series strain gages are designed for dynamic and limited static strain measurement at hightemperature.These strain gages are manufactured using a round wire for superior bonding ability and performance. A high-fatigue wire (Option Z) is also available on each of the gages. These gages are supplied with a fiberglassreinforced tape carrier which holds the grid and leads in place during installation and are bonded using ceramic cements or Rokide® flame spray. The shelf-life of thesegages is 9 months.
-
Product
Pressure Sensors
-
Universal pressure measurement for liquids and gasesSICK offers a portfolio of electronic pressure measurement transmitters and switches that can be adapted to individual customer requirements because of intelligent and varied configuration options. Typically, all SICK devices feature the use of high-quality materials, rugged properties, and precise measurement technology, in addition to being easy to operate and install.
-
Product
Temperature, Humidity, Bar. Pressure Transmitter
T7310
-
Built-in relative humidity, temperature, atmospheric pressure sensors. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Pressure Meters
-
Ensure optimal pressure levels across several circumstances with our pressure meters. Netech offers four versatile digital pressure gauges suitable for numerous medical and industrial applications. These devices also perform vacuum gauge measurements.
-
Product
Portable for Temperature/ Humidity/ Pressure
-
Portable Data Logger for Temperature, Humidity and Pressure.
-
Product
General Purpose Pressure Sensors For High Frequency
-
PCB® Series 113B dynamic pressure sensors set the standard for extremely fast, micro-second response with a wide amplitude and frequency range. These characteristics allow them to excel in high-frequency applications, where minimum sensor diameter is required.
-
Product
Low Differential Pressure Switch -
1800
-
Essential for industrial environments, the Series 1800 combines small size and low price with 2% repeatability for enough accuracy for all but the most demanding applications. Set point adjustment inside the mounting stud permits mounting switch on one side of a wall or panel with adjustment easily accessible on the opposite side. UL and CSA listed, and FM approved.
-
Product
Digital Automatic Pressure Regulator
UR-Z700 Series
-
The high performance auto pressure regulator UR-Z700 Series has electronic regulators with high-precision pressure sensors and high resolution, fast response piezo actuator valves. They control the pressure relative to the external control signal that they receive. For both Digital/Analog and DeviceNet™ communications.
-
Product
Pressure Calibrator
HPC40
-
AMETEK Sensors, Test & Calibration
The HPC40 Series handheld pressure calibrator is the world's first combined pressure and mA loop calibrator to be fully temperature compensated from -20 to 50°C. You can count on the same accuracy whether measuring pressure, current, voltage, or temperature.
-
Product
UPG-07 Ultrasonic Precision Thickness Gages - Color
UPG-07
-
100K thickness datalogger with export to Excel 8 0z. Operates on 2 AA batteries Measures all engineering material Store and Recall setup for use with multiple materials All software options are field-upgradeable Vibrate and color change on alarm Illuminate the keypad on alarm condition Inform the operator when to replace the transducer Simple user-interface
-
Product
Pressure Decay Test Systems
-
Pressure decay leak testing technology has become a mainstay in the arena of high volume production testing. Pressure decay testing methods offer the world's manufacturers a cost-effective and easily applicable solution to the leak testing challenges they encounter on a given day. Fundamentally, pressure decay testing is a straightforward measurement technique; Cincinnati Test Systems (CTS) pioneers new and innovative ways to integrate our technology into custom turnkey systems that exceed the industry standards for reliability and repeatability. CTS' 30+ years of experience goes way beyond the pressure test unit by offering our customers comprehensive, custom turnkey solutions to the most challenging leak testing problems.
-
Product
Brake Hydraulic Pressure and Electric Parking Brake Systems Test Bench
Model BHP/EPB™
-
The new Model BHP/EPB™ Brake Hydraulic Pressure (BHP) and Electric Parking Brake (EPB) Systems test bench from MB Dynamics accurately measures and controls the hydraulic pressure and EPB power levels applied to brake calipers during automotive buzz, squeak and rattle (BSR) testing, as well as brake durability, stability, functional or performance testing. Varied brake pressures are applied according to timing diagrams, as well as automated or manually program-controlled repeat cycles, as required to assess brake caliper/rotor assembly noise, useful service life, and other critical performance metrics.
-
Product
OEM Differential Pressure Switch
MDS
-
The Series MDS Pressure Switch is designed with a double diaphragm to protect false actuation due to shock and vibration. This low cost pressure switch has a minimum 20 million cycle life expectancy, and an extremely fast response time, making this an ideal device for OEM orders
-
Product
Explosion-Proof Differential Pressure Switch
1950G
-
The Model 1950G Explosion-Proof Switch combines the best features of the popular Dwyer Series 1950 Pressure Switch with the benefit of natural gas compatibility. Units are rain-tight for outdoor installations, and are UL listed for use in Class I, Groups A, B, C, & D; Class II, Groups E, F, & G and Class III atmospheres, ATEX for EExd IIB & Hydrogen T6, and CSA & FM approved for Class I, Div. 1, Groups B, C, D; Class II, Div. 1, Groups E, F, G and Class III atmospheres
