Conductance
See Also: Battery Conductance Testers
-
product
Digital Dailysate Meter
Digital Dialysate Meter™ D4 & D6
The DIGITAL DIALYSATE METER is specifically designed to test both acetate and bicarbonate dialysate quality. Measure Conductivity, pH and Temperature to ensure proper mixing during dialysate preparation and as a final check of dialysate quality before hemodialysis treatment. There are no strips or reagents that expire or subjective interpretation of results. Internal sensors require the user to place the sample in the instrument, preventing contamination of dialysate by the measurement device.
-
product
Bulk Current Monitoring Probe
MP-50
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
product
CTDs: Profiling
Profiling CTDs make continuous measurements as they travel through water. When lowered over the side of a ship or integrated with an autonomous vehicle, they map a vertical column of water's characteristics. Compared to moored CTDs, profiling CTDs account for dynamic errors introduced by moving through water and sample rapidly to generate a high-resolution dataset over a short period of time. Sea-Bird Scientific profiling CTDs are:*Designed to perform under unique dynamic conditions found on moving platforms.*Pumped and ducted for constant flow to match temperature and conductivity response.*Plumbed so measurements are made on the same sample of water with a predictable delay and predictable flow effects.*Built with a rugged design for shipboard and autonomous deployments.
-
product
Troubleshooting Track Circuit Simulators
14900 Series
The 14900 seriesTrack Simulator features a front panel with standard set up resistors and terminals and electrically conductive model track to simulate a track circuit suitable for instructional and hands-on training purposes. A locked drawer provides additional switches, potentiometers, and controls that allow selective implementation of many faults commonly found in typical track circuits.
-
product
PXI High Density MUX BRIC, 80-Chan, 10-Pole
40-570-415
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
Carbon Sensor Conductivity Meter High-Concentration
HE-960HC
FPD manufacturing processesThe HE-960HC measures conductivity, which forms the basis for parameters in chemical and waste water management. Its dual calculation circuits and software, combined with carbon sensors, enable measurements ranging without switching. The HE-960HC can be used as a process concentration meter, and also to monitor changes in the concentration of specified chemicals.
-
product
CompactPCI
3U PMC Carrier
This conduction cooled 3U CompactPCI single slot PMC provides an active interface between the CompactPCI bus (backplane) and a PCI Mezzanine Card (PMC). This product addresses the needs of aerospace, military, and rugged applications. It contains a thermal heat frame made of aluminum that fits together with conduction cooled PMC modules. Conduction cooling conducts heat away from the hot spots of the board and transfers the heat to the card edges and to the system chassis. No active ventilation is necessary inside of the system, which means the boards are sealed from the environmental influences found outside of the chassis. The heat frame and integrated wedge locks for the conduction cooling stiffens carrier and PMC module enabling the board to resist high shock and vibration.
-
product
PXI 3A Power MUX BRIC, 16-Channel, 12-Pole
40-571-304
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Solidtron Thyristors
The Solidtron family of products employ our advanced high voltage thyristors having incredibly fast and predictable turn-on performance as well as remarkably low conduction loss. These key attributes make Solidtron products ideally suited for use in a wide variety of pulsed-power applications where precise turn-on characteristics, reliability and longevity give them distinct advantages in certain applications over tube and spark-gap technology.
-
product
R.F. Coupler and high Pass Filter
7415-3
There are those who disagree with the r.f. conducted susceptibility test setup of Method CS02 of MIL-STD-462. Homemade rigs have sprouted to comply with the coupling capacitor requirement, each with it own disadvantage. Our little Type 7415-3 R.F. Coupler is the answer. A neat little box with BNC connectors and a pair of binding posts, it is rated at 270 V.A.C. at the LINE terminals and 20 volts PMS into the GEN port. Looks good and does a fine job.
-
product
Carbon Sensor Conductivity Meter (Low concentration type)
HE-480C-GC
The length of the sensor has been reduced by 50% as compared to existing systems to reduce space requirements. At the same time, the measurement range has been increased tenfold, enabling the system to measure even samples with comparatively high concentrations. Two different types of chemicalresistant glassy carbon sensors can be used, making the system ideal for chemical dilution/recovery management and pure water recycling as well.
-
product
EMC Subracks
1101.10
VECTOR Electronics and Technology, Inc.
VectorPak™ EMC subracks for medium and light duty applications. Its features include 2.5mm thick side panels / rack flanges and conductive finish throughout.
-
product
Thermal Conductivity Analyzer
TCi
The default C-Therm TCi Thermal Conductivity Analyzer employs the Modified Transient Plane Source (MTPS) technique in characterizing the thermal conductivity and effusivity of materials.
-
product
Portable Thermal Conductivity Analyzer
CI2100-RQD
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
CI2100-RQD portable thermal conductivity analyzer adopts imported high performance intelligent thermal conductivity sensor as measuring unit, which is based on microprocessor. It can test H2 concentration correctly in N2 and H2 mixed gases in a short time. - See more at: http://en.ci-ele.com/dcb675d2-4e33-4eb9-33a0-60edf78c9348/efb4c1eb-f4f5-70af-3ddd-ba6c1066c3fa.shtml#sthash.lXHNyKR1.dpuf
-
product
High Temperature ICP® Accelerometers
PCB® offers specially designed and tested ICP® accelerometers for conducting vibration and shock measurements under demanding environmental conditions of up to 356 °F (180 °C). These sensors combine proven quartz and ceramic shear sensing technology with specialized, built-in microelectronic signal conditioning circuitry to achieve dependable operation in extreme temperatures and through repetitive temperature cycling. Laser-welded, hermetically sealed, lightweight titanium or stainless steel housings offer further protection from the environment. Prior to shipment, each sensor undergoes a battery of tests to ensure survivability for its intended use. Such tests include temperature soak at elevated temperatures, temperature cycling, and exposure to highly accelerated screening procedures with hydraulically actuated shakers.
-
product
Waterproof Eco Tester EC High
EcoTestr EC High
The Eutech EcoTestr EC series comes with rugged, sturdy stainless steel pin sensors, giving you quick, reliable conductivity measurements. Ideal for use in a wide range of conductivity applications, such as hydroponics gardening, fish-farming, pools, electroplating and other water/ wastewater applications.
