Switches
enable on off function or change of direction.
See Also: Membrane Switch, Coaxial Switches, Crossbar, High Voltage Switching, Fiber Optic Switching, Microwave Switching, Optical Switch
-
Product
High Voltage Breakdown Tester
Model HV-55
-
Laxtronics Instruments & Controls Pvt. Ltd
5 Kilo Volt AC, 5 Kilo Volt DC, 30 Milli Ampere, Timer 0 To 100 Seconds, HV Prods, Start-Stop-Trip-Reset Using Single Switch On The Test Prods. Start Function Apply Test Voltage From 0 To Set Voltage Gradually.
-
Product
PXI 2A Multiplexer, 8-Bank, 8-Channel, 2-Pole
40-614C-004
Multiplexer Module
This 8-bank, 8-channel, 2 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Single-Mode
40-855A-312
Multiplexer Module
The 40/42-855A-312 is a PXI/PXIe 2-channel multiplexer with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXI 8 Slot BRIC 99x16 2-pole (9 sub-cards)
40-562A-122-99X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Analogue (1kV below) Insulation Tester
2132 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on low ohms : 3Ω & 500Ω.● Compact and lightweight.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test. ● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
Product
PXI Differential Fault Insertion Switch Modules
-
Pickering's PXI Differential Fault Insertion Switch Modules support multiple channels of two-wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to externally applied fault conditions. *Two module types are available: Two wire fault insertion module suitable for CAN Bus and FlexRay.*High bandwidth two wire fault insertion module suitable for Gigabit Ethernet, AFDX and BroadR-Reach.
-
Product
IEC60884 Fig22 Plug Socket Covers Pendulum Impact Test Apparatus
CX-BC22
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig22 plug socket covers pendulum impact test apparatusMeet the standard: IEC884-1 Figure 22-26,, IEC60068-2-75Uses: Suitable for household and similar plugs and sockets, wall mounted mounting boxes, screw glands, covers, switches and other electrical accessories for mechanical strength test
-
Product
PXI Single 44x4 Matrix, 1-Pole Switching
40-523-021
Matrix Switch Module
A 44x4 medium density matrix - product range comes with available reedrelay formats of 1-pole, 2-pole and 1-pole screened. The screened version is suitablefor switching signals up to 50MHz. These PXI matrix cards are constructed using highreliability ruthenium electro-plated reed relays, offering >10e8 operations togive maximum switching confidence with long life and stable contact resistance.
-
Product
LXI Optical Switching - 2:1 Multiplexer Plugin Module
65-281-381
Multiplexer Module
The 65-281-381 2:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
Product
PXI Dual 6 Chan Mux 18GHz 50ohm SMA
40-785-522
Multiplexer Module
Pickering Interfaces PXI Microwave multiplexer modules are suitable for switching 50_ signals up to 40GHz. The 40-785 is available as a single or dual 6 channel multiplexer, with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI/PXIe Fault Insertion Switch, 32-Chan 2A, N/C Through Relays, Fault Buses on M & U
42-190C-212
Fault Insertion Unit
The 40-190C-212 (PXI) and 42-190C-212 (PXIe) are fault insertion switches with 32 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Rotary Limit Switch
-
AMETEK Sensors, Test & Calibration
When motion is expressed in shaft rotation, we can provide limits that are adjustable throughout the entire range of movement. Rotary limit switches can be used for material handling on crane or winch drums, hoists, lifts, screw jacks, or platforms.
-
Product
Bourdon Tube Operated Pressure Switch
DA/DS
-
Customers tell us that this is the best pressure switch made. The Mercoid D Series is one of the world's broadest lines of pressure switches. Whatever your application might be, it is most probable it can be fully satisfied with a D Series pressure switch
-
Product
LXI Microwave Multiplexer, SP6T, 13-Bank, 50GHz, 50Ω, SMA-2.4, Terminated
60-800-713
Microwave Multiplexer
High performance RF multiplexer suitable for switching microwave signals up to 50GHz with automatic termination of unused signals
-
Product
PXIe Power Relay Module, 12xSPST, 16 A, With Interlock
42-161A-002-HI
Relay
The 40/42-161A-002-HI is a PXI/PXIe 12xSPST power relay module with optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
Flow Switches
-
Not susceptible to contamination and can be oriented in any pipe configuration make these flow switches for liquid or air maintenance free and reliable. Mechanical and electronic designs available
-
Product
RS-232 Auto Powered Line Driver
Model 201
-
FEATURES: Operates with only Pins 2(TD), 3(RD), & 7(GND); Screw Terminals and RJ-11; DTE/DCE Switch; Built in Surge Protection; Male or Female RS-232; 19.2 KBPS, Full Duplex, 2.1 Miles. The Model 201 RS-232 Auto Powered Line Driver requires only TD, RD, and signal ground for power and full duplex operation up to 19.2 K BPS.
-
Product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 8-Channel, 16-Pole
42-614D-019
Multiplexer Module
The 40-614D-019 (PXI) and 42-614D-019 (PXIe) 1-bank, 8-channel, 16-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
High Isolation USB Switches
-
RF gain block amplifier from Pasternack is featured in our extensive in-stock RF amplifier selection. Our connectorized gain block RF amplifier uses SMA connectors. This SMA gain block amplifier has a minimum frequency of 500 MHz, a maximum frequency of 2 GHz and a typical gain of 17 dB.
-
Product
LXI 50Ω 6:1 Microwave Multiplexer 4-bank 18GHz SMA
60-800-004
Multiplexer Module
High performance RF multiplexer suitable for switching microwave signals
-
Product
Power Switches With USB Charge Controller
-
ST’s USB charger emulator family (STCC) features ICs integrating a power switch, a data switch and an intelligent charge controller. It supports most charging schemes on the market (standard and proprietary) to ensure compatibility with a broad range of portable devices. ST’s unique and patented attach detection mechanism makes the STCC family ideal to guarantee fast and accurate charging while preserving the host battery.
-
Product
Clutch and Brake Applications
-
Customizable to your needs, CTS offers products and capabilities ranging from a simple switch to a dual output sensor and is an industry leader in pedal position technology. From accelerator to clutch and brake, rotary or linear, contacting or non-contacting (Hall-effect), whatever your need, we have a solution.
-
Product
Windows-Based Software Suite for Rigaku's X-Ray Diffractometers
SmartLab Studio II
-
SmartLab Studio II is a new Windows®-based software suite developed for the flagship Rigaku SmartLab X-ray diffractometer that integrates user privileges, measurements, analyses, data visualization and reporting. Newly available for the MiniFlex, the modular (plugin) architecture of this software delivers state-of-the-art interoperability between the functional components. Just one click switches from measurement to analysis. Watch real-time scans from one experiment while simultaneously analyzing other data on the same desktop by selecting an appropriate layout. The software provides various analysis tools such as automatic phase identification, quantitative analysis, crystallite-size analysis, lattice constants refinement, Rietveld analysis, ab initio structure determination, etc.
-
Product
Rugged Ethernet Switches
-
Today’s smart, sensor-based combat systems must acquire, process and share large amounts of real-time data from diverse sources continuously – and with a high level of readiness.
-
Product
24 Port PCI Express
PEX 8636
-
The ExpressLane™ PEX 8636 offers 36 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 24 flexible ports and fully conforms to the PCI Express Base Specification, rev 2.0. With 24-ports, the PEX 8636 is the largest PCIe switch in the industry serving the communications and networking markets. The PEX 8636 architecture implements Multicast as defined in the PCI Express Specification.
-
Product
Single 16x4 1-Pole High-Density PXI Matrix Module
40-520-403
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
Potable Coordinate Measuring Machines
Romer
-
A first in the world of portable measuring arms: The ROMER Absolute Arm features absolute encoders and is therefore the first measuring arm which does not require referencing before measurement. When the arm is turned on, it’s ready to go.Quality control, inspection, on-machine verification, reverse engineering, virtual assembly or 3D modelling. Wherever these needs arise, you will find the ROMER Absolute Arm. Much more than just a metrology tool, its value lies in its versatility.Portability, stability, light weight and high-performance laser scanners make the ROMER Absolute Arm an all-purpose 3D measurement, analysis and digitising tool that can be used by anyone, anywhere and with minimum training.Unlike many metrology devices, the ROMER Absolute Arm does not require warm-up time or initialization, thanks to a stable carbon fiber structure and industry leading Absolute encoders. Simply take the measuring arm to the part, switch it on and start measuring.
-
Product
16 Relay Output PCIe Board, 8 Isolated Digital Input Channels, 24V
APCIE-2200-16-8
-
8 electromechanical relays with change-over contacts The PCI-Express 16 relay board APCIe-2200-16-8 has 16 relay output channels and 8 isolated digital inputs, 24 V. 7 inputs are interruptible. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
Product
LXI Microwave Multiplexer, SP4T, 4-Bank, 18GHz, 50Ω, SMA
60-803-104
Multiplexer Module
Our 60-803-104 is a 4 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
C Series Current Input Module
Current Input Module
The C Series Current Input Module features programmable input ranges, variable connectivity options, and built-in noise rejection. You can also choose from options with built-in anti-aliasing filters or high-channel density to reduce the number of modules needed. The C Series Current Input Module supports safety features, certifications, input ranges, overvoltage ranges, and connectivity for applications such as power quality monitoring and metering, utility pole-mounted smart switches, utility pole-mounted smart grid reclosers, substation merging units, industrial machine measurements, health monitoring, predictive maintenance and prognostics, and phasor measurement units (PMUs). The C Series Current Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
