Switches
enable on off function or change of direction.
See Also: Membrane Switch, Coaxial Switches, Crossbar, High Voltage Switching, Fiber Optic Switching, Microwave Switching, Optical Switch
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, FC/APC Connectors, With Interlock
42-850A-014-M62.5-HI
Multiplexer Module
The 40/42-850A-014-M62.5-HI is a PXI/PXIe 4-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI 1 Bank of 80 Channel 2 Pole MUX
40-615-022-1/80/2
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXI 4 Slot BRIC Solid State 192x8 1-Pole (6 sub-cards)
40-563A-021-192X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 4x4 10GHz Matrix
40-787-518-4X4
Matrix Switch Module
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module
-
Product
Bench/System Multi-Range DC Power Supply With Digital Control, 3 Or 4 Outputs, 315 To 420W With/without Remote Interfaces
MX Series
-
Three or four high performance outputs each with full functionalityRange switching gives variable voltage/current combinationsShared power mode provides double power from a single outputLow output noise and ripple via linear final regulationHigh setting resolution of up to 1mV and 0.1mAVariable OVP and OCP trips on all outputs50 setting memories per output plus 50 linked memoriesSelectable voltage tracking (isolated tracking)Selectable current meter averagingSwitchable remote sense capabilityGraphic LCD provides simultaneous output meteringNumeric or spin-wheel control of all parametersIndividual or combined output on/off control with programmable delay sequencing.3U half-rack case for bench or rack mounting (4U rack kit accessory available)RS-232, USB and LAN (LXI) interfaces (P models)GPIB option (P models only)Duplicate power & sense terminals at rear (P models)
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 2 Channels (Single Ended) or 2 Channels (Differential)
M2P.5961-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
PXI Single 8x4 1-Pole 10A Power Matrix
40-551-001
Matrix Switch Module
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, also available with loop-thru has an additional 20-way GMCT plug for module-to-module connection. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
-
Product
PXI High Density Multiplexer, 4-Bank, 20-Channel, 2-Pole
40-615A-008
Multiplexer Module
The 40-615A-008 is a 4-bank, 20-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-800B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Isolated PWM Controllers
-
Renesas offers a broad portfolio of single-ended and double-ended isolated PWM controllers, and zero-voltage switching (ZVS) full bridge controllers.
-
Product
LXI High-density 256x4, 2A Matrix
60-553-002
Matrix Switch Module
These high-density single pole LXI matrix modules are capable of switching up to 150VDC/100VAC, or 2A (60W max). The use of high-quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
Product
PXI 64x6 Matrix Module, 1-Pole, 2A, 60W
40-576-001
Matrix Switch Module
The 40-575/576/577/578/579 are a range of high density matrix modules able to switch up to 2 Amps or 300VDC/250VAC. They are constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 1-Bank 40GHz SMA-2.9
60-801-401
Multiplexer Module
The 60-801-401 is a 6-channel, 1-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI 10A Power Multiplexer, 1-Bank, 16-Channel
40-661A-103
Multiplexer Module
The 40-661A-103 is a single pole, 1-bank, 16-channel PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
Product
Dual 16x2 1-Pole High-Density PXI Matrix Module
40-520-501
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
LXI Microwave Multiplexer, SP6T, 7-Bank, 50GHz, 50Ω, SMA-2.4, Terminated
60-800-707
Microwave Multiplexer
High performance RF multiplexer suitable for switching microwave signals up to 50GHz with automatic termination of unused signals
-
Product
Darlington Arrays
-
Darlington devices are high-voltage, high-current switch arrays containing multiple open-collector Darlington pairs or multiple Darlington transistors with common emitters, and integral suppression diodes for inductive loads. The nominal current rating of each output is 500 mA for the 7- and 8-output devices and up to 1.5 A for quad-output devices. The inputs are pinned opposite the outputs to simplify the application board layout. These devices interface standard logic families.
-
Product
Pattern Generators
PG314P Series
-
The MicroImage PG314 series of pattern generators are for applications to display custom designed patterns on screen. The PG314 units will overlay the pattern or patterns on top of the video signal provided to the input of the device. While the PG311 can be factory programmed with only one unique pattern, the PG314 can hold up to four patterns and switch between them.
-
Product
PXI 10A Power Multiplexer, 5-Bank, 6-Channel
40-661A-005
Multiplexer Module
The 40-661A-005 is a single pole, 5-bank, 6-channel PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available.
-
Product
PXI 8 Slot BRIC 132x4 2-pole (3 sub-cards)
40-562A-122-132X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 2A Multiplexer, 4-Bank, 4-Channel 8-Pole
40-614-009
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PXI 4 Slot BRIC 110x8 1-Pole (5 sub-cards)
40-562A-021-110X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Loop and Line Powered Level Switch
Safety IntelliPoint
-
The Safety IntelliPoint level switch provides a capacitance probe level switch with either a current output or relay contacts and “On-Board” self-diagnostics to ensure reliability. This SIL Intellipoint conforms to SIL 2 specifications providing the ultimate in level switch integrity and level sensing elements for a wide variety of temperatures, pressures, and materials.
-
Product
LXI Microwave Multiplexer, SP6T, 11-Bank, 50GHz, 50Ω, SMA-2.4, Terminated
60-800-711
Microwave Multiplexer
High performance RF multiplexer suitable for switching microwave signals up to 50GHz with automatic termination of unused signals
-
Product
PXI Solid State Multiplexer, Dual 3-Channel, 30 Amp
40-667B-011
Multiplexer Module
The 40-667B-011 is a dual 3-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI/PXIe High Voltage Multiplexer, Single 23-Channel, 1-Pole
40-321-107-HI
Multiplexer Module
The 40-321-107-HI (PXI) and 42-321-107-HI (PXIe) are single 23-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
ABex Terminal Module for Göpel 1149Cx BSCAN Cards
ABex TM-1149Cx
-
The ABex TM-1149Cx is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C2/X or SFX/PXI(e) 1149/C4/X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan cards it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
Product
PXI 12-Slot BRIC Matrix, 132x8 2-Pole (6 sub-cards)
40-562B-322-132X8
Matrix Switch Module
The 40-562B-322-132X8 is a high density BRIC12 matrix module with a size of 132x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
LXI Dual 2x2 Optical MUX LC Multi-Mode
60-851-405
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Single-Mode, 9/125 Fiber
40-855A-212-HI
Multiplexer Module
The 40/42-855A-212-HI is a PXI/PXIe 2-channel multiplexer with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
