Line Impedance
See Also: Line Impedance Stabilization Network
-
Product
Service Telephone for POTS / Analog Line
1TA701
-
Test Phone is self-powered, portable telephone test set for use by servicemen that are providing installation, maintenance and repairs of the terminal telecommunication equipment. Test Phone is intended to be used in normal environmental conditions.
-
Product
10 Gb/s Programmable Digital Delay Line
QPDDL10
-
The QPDDL10 series delay lines are four channel precision time delay generators for digital signals. Delays are controlled precisely in 5 ps increments at data rates up to 10 billion bits per second or clock rates exceeding 5 GHz. Each of the four channels is independently programmable.
-
Product
PRO Banjo Pro Line Tester
TC-BJ100
-
The Banjo Pro features convenient testing in both data and POTS environments. The black RJ45 plug is used for testing in eight conductor environments. "Just Flip It" to the red RJ11 plug for testing of two, four, and six conductor POTS environments.
-
Product
PCB Transmission Line Field Solver
Si9000e
-
With its fast, accurate, frequency-dependent transmission line modelling, the new Si9000e is designed to model transmission line loss, impedance at given frequencies and extract full transmission line parameters over a wide range of popular PCB transmission lines (over 90 structures).
-
Product
Guidance Laser with Remote In-Cab Line Adjust
GL3000P
-
The GL3000P Guidance Laser uses an ultra high visibility green laser to establish visual line control for the vehicle driver. Used for highway paint striping, asphalt distributors, road wideners, pavement profilers, or virtually any application requiring vehicle line control. GL3000P model is for truck cab mounting.
-
Product
3 GHz Programmable Delay Line
PADL3
-
The PADL3 is a single channel programmable delay line instrument designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 3 GHz
-
Product
RS-232 Auto Powered Line Driver
Model 201
-
FEATURES: Operates with only Pins 2(TD), 3(RD), & 7(GND); Screw Terminals and RJ-11; DTE/DCE Switch; Built in Surge Protection; Male or Female RS-232; 19.2 KBPS, Full Duplex, 2.1 Miles. The Model 201 RS-232 Auto Powered Line Driver requires only TD, RD, and signal ground for power and full duplex operation up to 19.2 K BPS.
-
Product
System for Determination of Materials Impedance in Impedance Tubes
-
System for determination of materials impedance in impedance tubes is used for evaluation of material’s acoustic properties.
-
-
Product
Optical Coherence Tomography Imaging Line Scan Cameras
OctoPlus Range
-
Teledyne e2v spent 2 years developing a CMOS sensor specifically for OCT. This resulted in the launch of OctoPlus, which has a specially designed pixel architecture that improves sensitivity and reduces signal roll-off to improve image quality by several dB vs state-of-the-art CMOS cameras, especially in deep structures.
-
Product
Hipot Line Testers
-
The newest product of our Hipot Line Testers, the UL Listed HT-S series hipot now comes with an adjustable ground continuity test in range of 0.08 - 1.50 , and Auto-offset for test leads up to 1.00 . Performs 0-2000 AC Hipot Test. Neutral/Hot to Ground Leakage current test up to 20 mA AC. Easy to use and connect. Ships complete with cables, manual, and a Calibration Certificate.
-
Product
High Impedance Active Probes
28 AND 29
-
Designed to serve the needs of integrated circuit engineers working in the most advanced high speed, submicron, MOS technology. These high frequency instruments include the attractive features of the Models 18C and 19 including full dc capability, negligible dc current drain, and extremely low input capacitance. In addition the frequency range of the Models 28 and 29 has been extended to a full 1 GHz.
-
Product
Vector Impedance Analyser
TE3000
-
The TE3000 Vector Impedance Analyser is a portable desktop instrument designed for high accuracy impedance measurement. The probe style construction and small output signal make it ideal for "in circuit" impedance characterisation of small signal devices without the risk of damage to the device under test. The TE3000 comes factory calibrated to the tip of the probe with optional custom calibration. Turn it on, set the frequency, take a measurement, and display the results in any format.
-
Product
Manual Tuners / Impedance Tuners
-
Maury manual tuners are based on precision slide screw technology that utilizes broadband slab line transmission structure and passive probes to create impedances for devices. The probes are designed to be very close to onequarter wavelength in the linear dimension at the mid-band of each range. Since each tuner has two probes, this results in improved matching characteristics for each unit. Another key feature of this series of tuners is the inclusion of a LCD position readout of the carriage position on those units operating below 18 GHz. Higher frequency tuners utilize a micrometer carriage drive. The positional repeatability and high matching range of these tuners make them ideally suited for use as a variable impedance source in applications like device characterization. Such measurements depend upon the ability of the tuner to establish impedances out near the edge of the Smith chart and to reproduce the electrical characteristics as a function of mechanical position. The tuners in this series are also easy to use due to the nearly independent electrical results of the mechanical motions. The depth of penetration of the probe into the transmission line determines the magnitude of the reflection, while the position of the probe along the line determines the phase. While there is some interaction, the effects are almost independent of each other. https://www.maurymw.com/images/mw-rf/mst982e35.jpg
-
Product
Single-in-Line Reed Relays
Series 115
-
SoftCenter construction Highest quality instrumentation grade switches Plastic package with internal mu-metal magnetic screen They take up the minimum of board area, conservingboard space Insulation resistance greater than 1E12 Ohms 100% tested for dynamic contact resistance for guaranteed performance 5 or 12 Volt coils with optional internal diode
-
Product
Analyzer for Safety Agency Production Line Testing
HypotULTRAIII
-
Ethernet Communication CardUSB/RS-232, GPIB & Printer InterfacesData Storage CardInterconnection to Modular Scanning MatrixOptional 10 Volt Analog InterfaceStorage of up to 50 setups with 30 steps per setupPatented SmartGFI® functionPatented prompt and hold functionPatented CAL-ALERT® functionPatented VERI-CHEK® functionReal Current measurementDual Continuity test modesBuilt-in security settingsLine and Load regulation
-
Product
M-Power-line
-
The M-Power-Line convinces with its robust design, high efficiency, compact dimensions and excellent price-performance ratio. By using a Power Factor Controller (PFC) the input voltage may vary from 100V to 254V. This means that the devices can be used anywhere in the world regardless of the typical national power supply system. The simple operation and easy readability of relevant characteristic values (target/actual/state/alarm message) make the devices particularly attractive for use in many branches of industry as well as research institutes.
-
Product
Transmission Line Probes
-
Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.
-
Product
Power Line Communication (PLC) Module For Single Board Computer
MIOe-PLC
Single Board Computer
Dual QCA7006 for EVSE / Charging Station sideEthernet Host Interface, SPI OptionalExtended Operating Temperature -40~85° C
-
Product
Very Compact Linear Line Array Loudspeaker
LINA
-
Easily the smallest and lightest in the series, LINA and its companion control element 750‑LFC bring the inherent linearity, low distortion, and exceptional power-to-size ratio of LEO Family technology to a wider range of applications and venues.
-
Product
High Impedance Active Probes
18C & 19C
-
High impedance probes, PICOPROBE® MODEL 18C and MODEL 19C, combine the most advanced MOS and bipolar technologies with special, low capacitance packaging techniques to achieve truly remarkable electronic measurement capabilities. While being manufactured each instrument is individually optimized for the best possible performance. The extremely low input capacitance, high input impedance, and almost negligible input leakage current permits the direct probing of even the most sensitive MOS dynamic nodes. At the same time, the full dc capability of this Picoprobe coupled with the high speed capability permits the full characterization of circuits.
-
Product
Dual-in-Line (DIL / DIP) Reed Relays
Reed Relay
Pickering Electronics Series 97 & 98 DIL / DIP Reed Relays feature the highest quality instrumentation grade reed switches making them suitable for the most demanding applications. They are available in two ranges featuring internal mu-metal magnetic screens.
-
Product
LXI WTB Adaptor, Thru line
60-982-001
-
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
Product
Advanced Line Protection System
ALPS
-
ALPS is a multi-function digital protective relay system intended toprovide distance protection for HV or EHV transmission lines. It maybe applied on or adjacent to series compensated lines. It is availablefor single or three phase tripping applications. Typical operatingtimes are to 1 cycle.
-
Product
Automated Control System for Veneer Edge Gluing Line
Vikat
-
The automated veneer splicing line control system is designed to identify defective veneer areas, control the scrap trimming, bonding of suitable areas and the formation of output sheets of a given size.
-
Product
Time Delay and Integration (TDI) Line Scan Camera
Piranha HS
-
The Piranha HS cameras provide an alternative to traditional line scan imaging. They enable you to meet the line rates and responsivity necessary for your high performance applications and allow you to reduce the number of cameras in your system. When you use fewer cameras, you use fewer framegrabbers, lenses, computers and cables. The Piranha HS family delivers the lowest price/pixel TDI system solution ever offered by Teledyne DALSA. Lighting costs can also be reduced. With TDI imaging, you can use LED lights, helping you to optimize system up-time and productivity.
-
Product
FC(Fuel Cell) Impedance Measurement System
KFM2150 System
-
The KFM2150 system is a fuel cell impedance measurement system configured with an FC impedance meter KFM2150 and an electronic load PLZ-4W series. Combination of KFM2150 and PLZ-4WA series (0V input type) supports impedance measurement for single cell of fuel cell.In addition to impedance measurement with AC impedance method, KFM2150 system provides IR measurement with current interrupt method.Application software enables test for each characteristic of fuel cell such as I-V characteristics, Constant Current characteristics, Current Interrupt method and Cole-Cole plot by the AC impedance method. Moreover, each test can be performed in a specified order.
-
Product
RS-232 Micro Line Driver - DB9 Connector
Model 209
-
FEATURES: Compatible with PC; 386/486 Pentium Com Ports; Full Duplex to 19.2 KBPS; No AC or DC Power; Screw Terminals or RJ-11; Small Size. The Model 209F offers all the features of the Model 201 Short Haul Modem but in a package that is approximately one third the volume.
-
Product
Single-In-Line Reed Relays
Series 106
-
SIL relays - 0.2 inch wide packages. Requires a board area of 0.2 x 0.8 inches (5.1mm x 20.3mm)
-
Product
625 KHz Data Acquisition Multifunction (Analog Output X2 Lines) PCMCIA
DAQi616MF(MF236/i)
-
The DAQi616MF is a type II PCMCIA I/O card for notebooks and other computers containing a PCMCIA slot.
