Wire
See Also: Contacts, Harness, Connectors
-
Product
Energy Analyzer
EP600i
-
The EnergyPro EP600i is portable and easy to use. Perfect for single phase or three phase energy consumption analysis and basic power quality monitoring. It supports standard wiring configurations and comes with a set of 1A - 2500A WideRangeFlexCT ™. The graphics display makes setup very easy and intuitive - you can setup and record data without looking at the manual!
-
Product
48-Channel High Performance Strain Gauge Measurement Instrument
EX1629
-
48-Channel High Performance Strain Gauge Measurement InstrumentSupports quarter-bridge (120, 350Ω or user defined), half-bridge or full-bridge24-bit ADCs, sampling rates up to 25 kSa/sBuilt in programmable differential excitation -8V to 8VBuilt in selectable bridge completionConfigure signal conditioning excitation and bridge completion on a per channel basisSimple, low-cost wiring using RJ-45 telecom connectorsSupports TEDS for easy transducer detection and setupRJ-45 input connector reduces setup cost and timeBuilt in self-calibration and shunt calibrationSupports voltage, ratiometric and linear measurements other than strain measurements.
-
Product
Process Carrier Pallets
Metalic Family
-
Process carrier pallets to carry the circuit boards through pick-n-place, IR reflow, gold wire bonding, epoxy dot encapsulating, and final fuctional test. Test Electronics will precision drill and customize pallets for your circuit board. Click on the Quote tab on the left then click on the Carrier Pallets tab to get an instant quotation on your process carrier pallets. Process carrier pallets can be designed to carry your circuit boards through assembly, wash and final test.
-
Product
PCI-6516, 32-Channel, ±30 V, Source Outputs, Bank-Isolated Digital I/O Device
779082-01
Digital I/O Module
The PCI-6516 is an industrial digital output interface, with one bank of channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6516 module is an industrial digital I/O interface, with all channels on an isolated bank. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6516 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
Standard DIP Socket with Solder Tail Bifurcated Contacts
Series 511
-
Standard DIP Sockets with Wire Wrap Bifurcated Contacts. Features: Standard DIP sockets are available with solder tail or wire wrap pins, all with bifurcated contacts. Consult Data Sheet No. 12005 for wire wrap pins. Aries offers these standard DIP sockets in more sizes than any other manufacturer.
-
Product
True-rms Thermal Multimeter
279
-
Thermal imaging multimeters are a first-line troubleshooting tool for electrical equipment that can check hot spots on high-voltage equipment and transformers, and detect heating of fuses, wires, insulators, connectors, splices and switches. Scanning with the 279 FC's thermal imager reveals many electrical issues rapidly and from a safe distance. By combining two tools into one, the thermal multimeter lightens the load and increases productivity.
-
Product
Wired LAN Routers
-
LAN routers with firewall features and general serial COM and WIFI features.
-
Product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Cut Ends, 2m
A009DF4-C-0A200
Cable Assembly
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation
-
Product
Insulation Tester
-
Cambridge Instruments & Engineering Co.
'CIE' Insulation Tester is a compact portable unit incorporating most modern features used for direct reading of electrical operating machines, Rotating Plant equipment, Stationary apparatus, Insulation Control switching equipment, Distribution networks, Communication cables, Insulators, Transformers, Industrial Installations, Cable, electrical components, wiring and other devices capable of carrying the rated voltages.
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m, HV
A037DM5-C-HA050
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Diaphragm Pressure Switch
CS & CD
-
Series CS and CD combine advanced design and precision construction in a small size. Unit is ideal for instrument panels, small compressors and general industrial applications. Visible set point and easy to wire SPDT snap switch reduce installation time. Operates in any position and is vibration resistant.
-
-
Product
AstroAI Multimeter
2000
-
AstroAI Multimeter 2000 Counts Digital Multimeter with DC AC Voltmeter and Ohm Volt Amp Tester ; Measures Voltage, Current, Resistance; Tests Live Wire, Continuity
-
Product
PXIe-8431/16, 16-Port, RS485/RS422 PXI Serial Interface Module
781473-02
Serial Interface
The PXIe‑8431/16 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Drawing Die And Wire Measurement
DGMS – Die Geometry Measuring System
-
Optik Elektronik Gerätetechnik GmbH
Measuring system for diameter, roundness, reduction angle and bearing length of wire drawing dies.
-
Product
DB25 Cable
PCL-10125
-
Double-shielded cable with 25-pin D-sub connectorsD-Sub 25 pin male, Blue x 2Tinned and strand copper wire with drain wire x 1Aluminum/Mylar foil and braided copper double-shielded cable effectively reduces EMI (electro magnetIsolated P.V.C. jacketUL20397 approvedIvory color
-
Product
PXI-4130, ±20 V, ±2 A DC, 40 W PXI Source Measure Unit
779647-31
Programmable Power Supply
±20 V, ±2 A DC, 40 W PXI Source Measure Unit - The PXI‑4130 is a programmable source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4‑wire) sense. With its five current ranges, it is ideal for transistor characterization that requires accurately sourcing a constant current or voltage while sweeping another current. The PXI‑4130 also includes a utility channel that can source either current or voltage. This PXI SMU can act as either a constant voltage source or a constant current source, with a settable compliance limit for either mode. In addition, you can enable remote sense on the SMU channel to maximize voltage output and measurement accuracy on your device under test (DUT) for high-precision applications.
-
Product
Enclosure, 9075, Removable Cover, 6" Depth
410112561
Enclosure
Enclosure, 9075, Removable Cover, 6" DepthThis 9075 ITA enclosure includes four handles for handling convenience and a removable cover secured by 14 fasteners (included) for easy internal wiring access. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Wireless Controller
Site Sentinel
-
Teledyne Gas & Flame Detection
Each system includes a tripod, network HMI, gas detection sensor(s), and alarm warning devices. An optional Sentinel SiteWatch provides remote access to system data via Ethernet or cellular communication. Power to the sensor assembly is supplied by a rechargeable Smart Battery Pack, disposable batteries or directly from HMI. Flexible and expandable, a Site Sentinel network can include up to 32 devices and consist of any combination of wireless and/or wired sensors, one or more HMI panels and optional solar panels. Additional sensors and/or remote alarm stations on tripods can be added as needed to assure widespread alert to site personnel.
-
Product
Digitizers
2745 Family
-
The 2745 Digitizer is a 64-channel digital signal processor for radiation detectors available in VME64 (V2745), VME64X (VX2745), and Desktop (DT2745) form factor. It offers not only waveform digitization and recording but also Multi-Channel Analysis for nuclear spectroscopy using Silicon strip, segmented HPGe, Scintillation detector with PMTs, Wire Chambers, and others. The 2745 can perform pulse height measurements (PHA), constant fraction timing (CFD), charge integration (QDC) and pulse shape discrimination (PSD) independently for each of the 64 channels.
-
Product
VTAC, Patchcord, ITA, 36", VTAC, DACAR 535, to Receiver, VTAC
7-141702142-036
VTAC Patchcord
Please note: The density/ thickness of DACAR 535 wire may require a module loading pattern that includes extra slot spacing to prevent wire bend and pressure. See the VTAC User Manual for more information.
-
Product
Power Meter Tester
MT-3551T
-
Kongter Test & Measurement Co., Limited
It is multi-functional in field testing for power meters and metering units of all wirings. Testing functions include: metering unit and power meter. With these function, it is widely used in power utility, substation, telecom machine room and the alike for power consumption examination, circuit breakage inspection, power abnormality analyzing, asset management and industrial production management.
-
Product
Network Cable Tester
PA-40
-
The PA-40 is designed to check both shielded and unshielded twisted pair (STP/UTP) and coaxial BNC-type network cables. With the push of a button, it tests all wires for continuity, miswiring, and polarization. Dual-colored LEDs let you identify correct and reversed pairs; using the included remote unit, cables may be tested before installation or after installation. Features tip/ring polarity test. Uses 1 9V battery.
-
Product
Vertical Hinged Mounting Frame, iCon, 5U, 4 Positions
310113508
Mounting Frame
The 5U Vertical hinged Mounting Frame mounts to standard 19" racks and hinges open to allow access to wiring between the instruments and VPC Receiver. The 4 cutouts are spaced evenly across the panel. iCon cover plate sold separately (310113467).
-
Product
Downloading Multifunction Tester
ET4500
-
The new ET4500 tester carries out all the tests needed to verify the safety of electrical installations in domestic, commercial and industrial wiring installations in accordance with the latest regulations.
can be used to carry out 3 wire earth testing and has on board memory to store and download all installation test results for documentation.
Everything about the new ET Series has been designed to save time and make testing easier.Fast, reliable high current and non-trip loop testing comes as standard together with a high level of input protection and a CAT IV safety rating .Supplied with a full range of accessories.
-
Product
Rear Cover, S6, Tabletop Configuration, For Part # 310 122 100
310113431
Protective Cover
The Rear Covers are designed to enclose the wiring that runs from the S6 Receiver on the tabletop to the instrument cards below. This rear cover is used with the S6 Receiver Part # 310 122 100.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
40-204-002
Multiplexer Module
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
Product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Tinned Ends, 2m, HV
A009DM5-T-HA200
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
50/75 Ohm Micro Coax Contacts
-
Rated to 3 GHz using RG 316 or RG 178 Max of 10.5 GHz using RG 316 Double Shield.Rated to 10,000 cycles.50 and 75 Ohm impedance.Mating force of 1.5 lb.High density I/O Crimp contact designed for RG 316, RG 178, and RG 179 wire.
-
Product
Cable Assy 26-Pin D-Type M/M 0.5m
40-970-026-0.5m-MM
Cable Assembly
The 26-Pin D-Type cable assembly is constructed from 7/0.15 (26AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 26-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
