Wire
See Also: Contacts, Harness, Connectors
-
product
ACCES Wireless Data Acquisition Products
There have been many inquiries about our wireless I/O products. Many of these requests begin with "This is just what I need, I can't hard wire to a PC because...". Let's face it, running cable in an industrial environment can be costly, especially when you consider all the material and manpower needed to finish the job. Additionally, how can you collect data on something that is in motion like a car on a track? Our Wireless I/O products are perfect for remote installations in harsh atmospheric, industrial or marine applications. These units offer a low-cost alternative to costly signal wire installations in applications such as agricultural and irrigations systems, building management and control, security and factory automation.
-
product
Distributed Motion Controller
As smart factories continue to expand the scale of their operations, more reliable and stable motion control axes and I/O points are required to meet the growing demand of adding more connected equipment. Other than centralized motion controllers, ADLINK provides complete and scalable distributed motion control solutions for machine automation for improved system expansion by supporting more than 256 axes and over 2000 I/O points with wiring that exceeds 100 meters for large-scale motion control automation such as electronic parts manufacturing.
-
product
Bench-Top Wire Crimp Pull-Force Tester
PT-1500
PT-1500 Bench-Top Wire Crimp Pull-Force Tester, Manual Lever-operated for 5.84mm 8-30 AWG
-
product
22-Pin REDEL High Voltage Cable Assembly, Male to Unterminated, Cut Ends, 0.25A, 0.5m
A022KMR-C-HA050
This is a 0.5m long male to unterminated 22-Pin REDEL high voltage cable assembly with cut ends constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips are provided to secure the connector to associated product.
-
product
Triple Alarm CAT IV Non-Contact Voltage Detector with Flashlight
FLIR VP50-2
The FLIR VP50-2 is a durable, CAT IV-rated non-contact voltage detector featuring light, vibration, and beeper feedback alarms and a powerful LED flashlight. Use the VP50-2 to reliably check if an AC circuit is live before beginning work; detect voltage on exposed conducting parts or through insulation; identify live wires within electrical panels, switches, and outlets; or trace live wires and map circuits. With an ergonomic and drop-tested design, the FLIR VP50-2 is the right choice for professionals performing field troubleshooting and verification of electrical installations within residential, commercial, and industrial buildings.
-
product
Low Voltage Test & Measurement
Low voltage testing is able to catch errors such as shorts and opens by applying current to a wire and measuring the voltage. The wire will have a current affected by several factors including resistance and components. If the wire is connected correctly, the test will read low resistance. That means current is flowing through the wire as expected and reaching the required connections. If the tester reads high resistance it means something is impeding the current from reaching its destination. This could be caused by a number of causes.
-
product
Cable Assembly, 50-Pin D-Type, Female to Female, 0.5m, Exit Towards Pin 1
A050DF5-050DF5-0A050
The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated
A068SMR-C-6A050
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
Cable 96-Pin Female to 100-Pin Male Micro-D, 2m
40-973B-096-2m-FM
The 96-Pin to 100-Pin SCSI Style Micro-D Adaptor Lead is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Metal Spring Latches are provided on the 96-Pin connector and 4-40 UNC screwlocks on the 100-Pin connector.
-
product
Cable Assembly 44-Pin D-Type Male to Female, 1m
40-970-044-1m-MF
The 44-Pin D-Type Density and a Half cable assembly is constructed from 7/0.15 (26AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
PCIe-8433, PCI Express, 2-Port, Isolated, RS485/RS422 Serial Interface Device
781745-01
The PCIe‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
Impulse Spark Tester
IT-25B
While most military standards now favor high frequency spark testing over impulse spark testing, the IT-25B Impulse Spark Tester is available for use in some aeronautic applications that still specify the impulse method. The IT-25B meets the test requirements of military specifications MIL-C-13777E, MIL-W-16878, and NEMA standards for hook-up wire used in high temperature wire applications. This method is favored as an alternate to a wet dielectric test.
-
product
J-Type Thermocouples Wire, Fiberglass (32 deg F to 900 deg F) 1 m
745690-J001
J-Type Thermocouple, 32°F to 900°F Temperature Sensor - The J-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the J-Type Thermocouple and acquire synchronized temperature data in units of degrees. The J-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
3 Wire (Analogue) Earth Resistance Tester
ST-1505
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● The timer operates automatically for about three to five minutes when the “PUSH BUTTON SWITCH” and “TIMER ON BUTTON” are pressed together. ● This will keep test “ON” for the duration of the timer.● Battery check function.● Calibration performed with supplied test leads.
-
product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Cut Ends, 2m
A068SFR-C-6A200
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
Monitoring System
A112
The photoelectric sensor model A112 allows to realize a system for detecting breaks of thin wires from 10 um in diameter, with a detection range greater than 50 cm.The A112 produces these results without the use of laser technology, allowing high immunity to vibration and a secure alignment between receiver and transmitter.
-
product
Earth Resistance Testers
Earth Resistance Tester is widely applied in ground resistance measurement, loop resistance measurement in fields such as electric power, telecommunications, meteorology, oil field, architecture and industrial electrical equipment, etc. When measuring ground system with loop, there is no need to disconnect the ground wire without auxiliary electrode, which means safer and faster.
-
product
Crossing Control Bypass Switch
XCBS-DL
The XCBS-DL is permanently wired into each crossing warning system, and can be configured with either a removable or non-removable bypass key. Simply connect the track connection harness to the designated track connection terminals. To prevent unnecessary operation of the crossing warning system, insert the key and select "bypass", rotate the knife switch to "bypass" and the crossing is disabled. When in the "bypass" position, a Dummy Track Load is connected to the track wire connections in parallel with the rails and the crossing approaches are shorted, preventing unnecessary activation when track equipment is working in the crossing approach circuit. The opening of one track lead may be desired to prevent unnecessary activation with intermittent shunting on the crossing approaches close to the crossing.
-
product
Cable 96-Pin Micro-D Female to Unterminated, Tinned Ends, 0.5m
A096SFR-T-5A050
The 96-Pin SCSI Style Micro-D to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
product
E1 Ethernet cable, twisted pair 1m
182219-01
8-Pin Male Ethernet to 8-Pin Male Ethernet, CAT-5E Ethernet Cable - The 8M-8M Ethernet Cable connects devices to network hubs or switches. The cable has straight-through wiring and is available in different lengths and thin profile options.
-
product
MS-M 26-Pin RF Cable Assembly, Female to Unterminated, 0.5m, RG316 Cable
40-979A-526-3-0.5m-FU
This 0.5m long MS-M RF 26-Pin cable assembly is constructed from RG316 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 68dB/100m at 500MHz. Screwlocks are provided to secure the MS-M connector to the mating connector.
-
product
Mating Coax Connector and 20 Coax Pins Crimped (both ends) to 5' wires
GX96405-60
Mating coax connector and 20 coax pins crimped (both ends) to 5 ft wires
-
product
Multisystem Ignition Analyzer
TA500
The TA500''s unique and proprietary technology allows the user to perform quick and reliable diagnostics of non-starts, misfires, fouled up or damaged spark plugs and/or spark plug wires, by comparing digital read-outs of the spark plug voltage and spark burn time between cylinders on engines using Coil on Plug, Coil near Plug, conventional distributor/ignition coil, DIS (Distributor-less) or waste spark and magneto technologies.
-
product
Impulse Winding Tester
TH2882A-5
Changzhou Tonghui Electronic Co., Ltd.
Due to the influence of coil wire material, magnetic material, framework and manufacture technics etc., coil products (such as transformers, motors, etc.) may have defects of low insulation between coil layers, circles and leads. TH2882A series impulse winding tester, adopting high-speed sampling technique, is a new generation analysis test instrument for insulation performance of coil products.
-
product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 31.5Ω
40-252-010
The 40-252-010 is a programmable resistor module with 4 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
HVFAA Horizontal Vertical FAA Flame Chamber
Atlas Material Testing Solutions
The Atlas HVFAA Horizontal Vertical Flame Chamber provides the most accurate means for determining the flammability of aircraft cabin and cargo compartment materials, liners and waste stowage compartment materials, and electric wire. The large volume chamber prevents oxygen depletion during tests. Three digital timers with remote control make specimen event timing precise and convenient. To ensure accurate and repeatable tests, an optional burner flame temperature verification kit is available. The HVFAA is the optimal instrument for conducting repeatable FAA flammability tests and is used in the FAA’s training facility.
-
product
DIELECTRIC and CONTINUITY TESTERS ( HI-POTS )
AV-25V-GC1-05
This tester is designed for testing equipment wiht a line cord which can be plugged directly to the tester. The continuity test is to determine whether the ground wire of the line-cord is well connected to the metal frame of the unit under test.
-
product
In Situ Process Management
KLA’s comprehensive portfolio of SensArray® products enables in situ monitoring of process tools’ environments. With wired and wireless sensor wafers and reticles, an automation package and data analysis systems, SensArray products provide comprehensive information for a wide range of wafer and reticle processes. Wafer process equipment manufacturers, IC manufacturers and reticle manufacturers use SensArray data to visualize, diagnose and control process conditions.
-
product
SparkFun Soil Moisture Sensor (with Screw Terminals)
The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straightforward to use. The two large, exposed pads function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil means the better the conductivity between the pads will be, resulting in a lower resistance and a higher SIG out. This version of the Soil Moisture Sensor includes a 3-pin screw pin terminal pre-soldered to the board for easy wiring and setup.
-
product
QTI Sensor
555-27401
The QTI Sensor is a close-proximity infrared emitter/receiver that is able to differentiate between a dark surface) with low IR reflectivity) and a light surface (with high IR reflectivity). These little sensors can be very handy for line following, maze navigation, or sensing the outer rim of a SumoBot ring. Wiring options allow it to be used digitally for fast black/white line following, or as an analog sensor to detect different shades of gray. A daylight filter is built into the sensor.
