Strain Gage Amplifiers
See Also: Strain Gages, Strain Gauges, Strain Gage Signal Conditioners
-
product
Charge Amplifiers & Signal Conditioning
The use of charge amplifiers alongside piezoelectric charge output sensors is still widespread in many industries. This is due to the rugged and high temperature capabilities of the sensors. There are many challenges in using these sensors and it needs a good understanding of the technology to get a quality, noise free signal for accurate data.
-
product
Portable Power Amplifier
PAV250Bip
PAV250Bip is the portable OPAL-RT used amplifier model, which is specially designed for R&D of power system simulation. It is designed with linear type amplifier so that it is with precise accuracy, which could be adapted to various capacitive and inductive load.
-
product
MOSFETs For High Frequency Amplifier
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
product
In-Line Charge Amplifiers
The in-line charge amplifier is used to excite structures or machinery with a definable impulse force. Resonances are identified by impulse, an important measurement parameter for the study of dynamic behavior. The 4705A1 is a fast turn on time, 50 mV/pc, in line charge amplifier with BNC jack connectors on each side.
-
product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
16-Channel Instrumentation Amplifier
PGA-16
The PGA-16 is a 16-channel instrumentation amplifier with differential input, single-ended output, programmable AC or DC input coupling and pre-filter gain.
-
product
VHF Band 1.0 Watt Amplifier With RF Bypass
Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.
-
product
19-inch Rack Mount(2U) 20 Watts 80MHz to 1GHz Power Amplifier
Chengdu KeyLink Microwave Technology Co., Ltd.
20 Watts 80MHz to 1GHz amplifier in a compact 2U package for oversea market. It is a rack mountable-unit incorporating a universal voltage power supply and a built in forced air-cooling system. This amplifier subsystem utilizes LDMOS power device that provides excellent power density, high linearity, low distortion and wide dynamic range. The KB00810S43A SSPA is ideal for EMC testing to various industry standard as well as Broadband Communication.
-
product
Amplifiers
Computer-controlled charge amplifier module features variable gain and output scaling and accepts either differential or single-ended inputs. Adjustable parameters include: accelerometer sensitivity, differential or single-ended mode, scaling, filter setting, external calibration and zero mode.
-
product
IRIG Amplitude Modulated Time Code Distribution Amplifier
1205A / 1205A-MC
Precise Time and Frequency, Inc.
The ptf 1205A is a 12-channel IRIG amplitude modulated time code distribution amplifier housed in a 1U high, 19″ rack package. The ptf 1205A uses an RF design combining the latest technology in low noise components to minimize input/output delays which are of the order of nano seconds.The unit uses two stages of input signal buffering to distribute the input signal to 12 separate outputs, and insure maximum isolation between individual output signals.
-
product
Strain Gauge Weighing
In the demanding environment of the metals processing industry getting the right balance between accuracy, speed and reliability in your sensing systems can mean a great deal. ABB offers a wide range of dedicated products for weighing applications for crane, scrap, blast furnace and continuous casting.
-
product
SV Range Broadband Power Amplifiers 0.8 GHZ - 3.2 GHZ
SV Series
Class A solid stateBroadband (instantaneous single band): 80 MHz 1000 MHzTypical output power : 100 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 100 W and H < -20 dBc up to 450 MHz andP1dB > 65 W and H < -20 dBc from 450 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to MT 200 possibleReliable, efficient and robust19" Rack3 years standard warranty
-
product
LT Range Broadband Power Amplifiers 20 MHZ - 1000 MHZ
LT Series
Class A solid stateBroadband (instantaneous single band): 20 MHz 1000 MHzTypical output power : 90 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 60 W and H < -20 dBc from 20 MHz to 80 MHz andP1dB > 75 W and H < -20 dBc from 80 MHz to 500 MHz andP1dB > 45 W and H < -20 dBc from 500 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to LT 160 possibleReliable, efficient and robust19" Rack3 years standard warranty
-
product
High Voltage Linear Amplifier
A800X
This unit is a version of A800 amplifier equipped with two inputs, DC-offset and output atenuation. Input A is a normal non-inverting one. Using this input alone makes A800X functionally identical with A800 amplifier.Input B can act as a inverting or non-inverting depending on the position of the corresponding switch.
-
product
Slim & High-Performance Charge Amplifier
6001-A, 6002-A
Measuring a wide variety of vibration: automotive, rail transportation equipment vibration, motor/pump vibration, vibration response during vibration test. Also available for a vibration test device for calibration of equipment.
-
product
Low Noise Amplifier
ZLNA-9K-6G-01
Low Noise Amplifier, Frequency 0.009~6000MHz, Gain 40dB, Noise figure 3.5dB, P-1dB power 8dBm, SMA Female
-
product
SOA & Raman Amplifier
They are designed for distributed Raman amplification in a narrow spectral range in C band.
-
product
Electric Transducer Driver Amplifier
7620
The Krohn-Hite Model 7620 is a 17/34 watt, wideband power amplifier that offers extended output power and voltage capabilities. Performance features not available in other power amplifiers, the 7620 provides a differential output and is able to deliver 17/34 watts of continuous power (68 watts at dc) and 141V/282V rms (400V/800Vp-p). It can also provide plus and minus dc voltages simultaneously.
-
product
PWM Servo Amplifiers
Direct digital pulse width modulation (PWM) amplifiers — along with PMAC controllers — provide highly accurate positioning for industrial applications.
-
product
Limiting Amplifiers
Teledyne Microwave Solutions (TMS) offer a range of Limiting Amplifiers which are used in instantaneous frequency and phase measurement receivers. The most important performance requirement of a limiting amplifier is to minimize output power variations, and provide a constant output over a wide input dynamic range.
-
product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
product
EHC-03 Basic Corrosion Thickness Gages
EHC-03
Danatronics is pleased to welcome our EHC-03 to our corrosion thickness gage family. The EHC-03 is designed to accurately and non-destructively measure metal structures subject to corrosion.
-
product
LINEAR AMPLIFIERS
F-series
The F-series amplifiers are designed to extend the output range of low voltage signal sources. They are general purpose devices with a very low output impedance, very fast response and high current. The output is linear from DC up to few megahertz range.
-
product
Operational Amplifiers
Op Amps
Operational amplifiers, known also as op amps, play a major role in analog signal conditioning applications. Invented by Karl Dale Swartzel Jr. in 1941, these products are largely used in today’s electronic devices.
-
product
Portable Power Amplifier
PAV120Bip
PAV120Bip（6*120V） is the portable type power amplifier which is specially designed for R&D of power system simulation. It is with linear type amplifier design so that it could be adapted to simulation experiment which may include various capacitive and inductive load.
-
product
Saluki S3871X Series Solid State Power Amplifier (max. 500W output power)
S3871X series is a broadband benchtop solid state power amplifier and incorporates the patended spatial power combination technology. It is designed to have features of broad bandwidth, high gain, high power, wide dynamic range, low spurious signals and extremely load tolerant. These features enable the amplifier to be used as a cable test instrument covering multiple frequency bands.*Wide frequency range, 9kHz to 110GHz, max. 500W output power*
-
product
Rack Mount Type Amplifiers
Amplifiers for each of O-, S-, C- and L-bands– Compatible with high-speed transmission (up to 100 Gbps)– Available for all signal types and protocols– Compatible with transmitters from all manufacturers– Compatible with SNMP
-
product
Video, Audio & Time Code Distribution Amplifiers
ESE has an extensive line of Distribution Amplifiers for both Video, Audio and Time Code. Our popular ES-207A is a small 1 x 4 video DA which can be tucked away anywhere. Other models have 1 x 8 and 1 x 12 capability. Rack-mount, PC card and "black box" configurations are available.
-
product
Ultra-broadband Power Amplifier Systems
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink provides ultra-broadband power amplifier systems in rack-mounted configuration with output power capacity from 50-Watt to 2000-Watt for applications including EMC testing, communications, and TWT replacement.
-
product
Measuring Amplifiers
VibroMatrix
The VibroMatrix measuring system consists of the USB measuring amplifier "InnoBeamer" and various software modules, which can be put together individually. Suitable for your measurement task. All you need is a computer or a notebook. The software enables you to measure in real time and record your data for later offline analysis in the office.
