Strain Gage Amplifiers
See Also: Strain Gages, Strain Gauges, Strain Gage Signal Conditioners
-
product
2-22 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5021
The HMMC-5021 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-22 GHz frequency range. Typical applications of the HMMC-5021 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gain response and excellent port matches over the 2-22 GHz frequency range.
-
product
4 Channels, Strain Gauge Measurement
SG1
Module SG1 is NAI’s latest generation Strain Gage Measurement Module. This intelligent, four-channel module is used on our Multifunction Embedded I/O Boards and Single Board Computers (SBCs).
-
product
High Speed High Voltage Amplifier
WMA-320
The WMA-320 is a high voltage, wide bandwidth laboratory amplifier. Its high output voltage, current and wide bandwidth have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-320 can be used for MEMS actuation, EO-modulators, PZT (piezo) positioners, ultrasonics, and many other applications.
-
product
Low Noise Amplifiers
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a variety of applications but are primarily suited to airborne, maritime and ground based radar systems. LNAs are primarily intended to minimise added noise whilst providing high gain so design focusses on the parameters associated with the noise response of the amplifier. They are usually the first amplifier in the Radar detection chain and will have the lowest noise figure.
-
product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
High-Speed System Sync and Distribution Amplifier - SOSA Aligned 3U VPX
Model 5503
- Supports Xilinx® Zynq® UltraScale+™ RFSoC FPGAs- Synchronizes up to 32 channels across four Quartz boards- Synchronizes sampling and data acquisition for multichannel systems- Provides single sample accurate synchronization between multiple channels and multiple boards- Synchronizes gating and triggering functions- Optional VITA 67.3D optical interface for backplane gigabit serial communication
-
product
Telecom Optical Amplifiers
Thorlabs' optical amplifiers for telecom applications are available as complete benchtop systems or as pigtailed butterfly packages. Our line of benchtop optical amplifiers includes a praseodymium-doped fluoride fiber amplifier (PDFA) and erbium-doped fiber amplifiers (EDFAs). Our optical amplifiers available in pigtailed butterfly packages include InP/InGaAsP or GaAs/InGaAs semiconductor optical amplifiers (BOAs or SOAs), and high-speed optical switches.
-
product
Driver Amplifiers
Analog Devices RF amplifiers are designed utilizing the company’s leading amplifier and RF IC expertise. Our extensive family of single-ended input/output, fixed-gain amplifiers can be used from dc to microwave and include gain blocks, low noise amplifiers, intermediate frequency amplifiers, driver amplifiers, and differential amplifiers. These devices offer high linearity, low noise figures, and various fixed-gain options, as well as low power consumption; they are all fully specified over frequency, temperature, and supply voltage for use in a variety of applications.
-
product
Low-noise High-voltage Amplifier For Tube-scanners -
HV200/5
The HV200/5 is a high-precision HV-amplifier designed for the control of tube scanners. It takes three input voltages In X, In Y and In Z (-10 V to + 10 V), amplifies them separately (input gain switches: x1, x2, x5, x10, x20) and adds an offset voltage between -10 V and +10 V. In a 2nd stage, the signal is amplified by a factor of 20. This enables its use as HV amplifier in scanning image acquisition applications, such as STM or AFM, with the capability to shift the scan range in high resolution imaging.
-
product
8-Channel VME Strain Gauge/Weighing Module
V380
The V380 is a VME/VXI compatible eight-channel strain-gauge signal conditioner which is optimized for load-cell weighing applications. The module includes tare (zero reference), DSP-based high-order filtering, averaging, triggered weighing, and other functions not commonly available in conventional strain-gauge signal conditioners.
-
product
Rugged Amplifiers And Transmitters
Communications & Power Industries
CPI TMD began developing power supplies at the end on the 1980s, expanding its amplifier product line. By leveraging this expertise together with its proficiency in microwave tubes and the complexities of integration, CPI TMD has build a thriving amplifier and transmitter business to serve the needs of its defence and communications customers.
-
product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
Capsuhelic Differential Pressure Gage
4000
The Capsuhelic gage is designed to give fast, accurate indication of differential pressures. The gage may be used as a readout device when measuring flowing fluids, pressure drop across filters, liquid levels in storage tanks and many other applications involving pressure, vacuum or differential pressure
-
product
Wideband GaN Amplifiers
The Teledyne RF & Microwave family of GaN-based amplifiers maximizes power density and efficiency, and establishes a new benchmark for small size in the 0.1 to 6.0 GHz range that operates over multi octave. With dimensions of 2.5"L x 2"W x 0.42"H at only 2.1 cubic inches, these modular, non-ITAR GaN amplifiers maintain the rugged design characteristics needed for harsh airborne and land based requirements.
-
product
Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier
USBPGF-S1
Single Channel USB Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier for Signal Conditioning in Data Acquisition Systems. Differential or single ended input. 10Vmax Signal Input and Output with input protection up to 40V. Software-programmable instrumentation amplifier gains of 1 to 1000.
-
product
Fiber Transmitter With Fiber Amplifier
FTFA 822B - 824B
- Work as Transmitter & Fiber Amplifier- AGC - Automatic Gain Control- Built in RF Booster- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lesers with Isolaters- Variable SLOPE Control- Output Wavelength : 1310nmPower Options :- 40V DC- 12V DC / 2 Amp- STB Adapter along with PSP- 7.4V, 2600 mAH Battery
-
product
Sound Source And Power Amplifier
Designed for acoustic application, with strong signal transmission capability and flexible measurement.
-
product
RF POWER AMPLIFIERS
BSA Series
RF Input: N-f, standard on rear panelRF Output: standard on rear panel<1 kW N-f<3 kW 7-16-f<5 kW EIA 1 5/8Mains Supply: Line Power:<1000 VA 100 ... 240 V AC ±10% / 47 ... 63 Hz1000 ... 3000 VA 200 ... 240 V AC ±10% / 47 ... 63 Hz>3000 VA 3x 400 V AC ±10% / 47 ... 63 HzElapsed Time Meter: via status displayAmbient Temperature: 0 ... +45 °CStorage Temperature: -20 ... +85 °CRelative Humidity: up to 95% (non-condensing)Operating Altitude: up to 2000 m above sea levelVibration and Shock: MIL-STD-810 GCooling: forced air with integral blowerair intake from front, air exhaust at rear
-
-
product
Low Noise Super Wide Band Amplifiers
WBA Series
WBA series low noise amplifiers have the octave bandwidth from MHz to GHz. With super low noise figure and exceptional low VSWR, WBA series LNA achieves exceptional gain flatness accross octave or multi-octave bandwidth.
-
product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800A (1RU)
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800A (1RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
product
RGB Digital Fiberoptic Amplifier
CZ-V20 Series
SUPER HIGH POWER RGB sensor Industry's best color differentiation. High resolution amplifier for triple 16-bit calculation. New Luster Detection Sensor Head. Dual digital display & Direct access. New UV sensor head for fluorescent Detection. Three detection modes for every target [Super I / C' / C+I]
-
product
RF High Power Amplifier Modules
Analog Devices MMIC-based GaN and GaAs power amplifiers cover the low hundred MHz frequency range up through and including components in the Ka-band (29 GHz to 31 GHz). Our portfolio also includes GaN-based power amplifier modules with output power exceeding 8 kW. Designed for excellent linearity at high output power, our power amplifiers maintain good heat dissipation and high reliability at elevated temperatures for the wide variety of test, radar, and aerospace and defense applications that they are used in.
-
product
Four Quadrant Power Amplifier
PAV3000
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
product
Voltage and Current Amplifier
CMS 356
The CMS 356 is a voltage and current amplifier for analog low-level signals provided by a CMC test set or by any other signal source, such as a digital real-time power system network simulator. When used in combination with a CMC test set, the amplifier extends the capabilities of the test set to provide additional output channels and higher amplitudes.
-
product
C-Band Separate Dispersion Compensation Raman Fiber Amplifier
DRA5228/F
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
product
FPGA Signal Averaging For Gage Digitizers
eXpert / Signal Averaging
The onboard Signal Averaging eXpert FPGA DSP feature is a powerful tool that allows users to detect a small repetitive signal in a noisy environment.
-
product
Measurement Amplifier In Rugged IP65 Housing
INELTA Sensorsysteme GmbH & Co. KG
For DMS Force Sensors and LVDT
-
product
4-Quadrant Power Amplifier For Simulation Applicaton
PAV20000
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
product
Logarithmic Video Amplifiers
DLVAs, ERDLVAs & SDLVAs
PMI’s Detector Logarithmic Video Amplifiers (DLVA, ERDLVA, SDLVA) are offered covering DC to 40 GHz with extended range models offering dynamic ranges over 70 dB. Our standard products provide exceptional temperature stability, log linearity and frequency response. As well, most SDLVAs provide a limited IF output. PMI offers custom DLVA’s and SDLVA’s to meet your requirements or replace obsolete products, please email your requirement to sales@pmi-rf.com so we can propose an instant solution.
