Bridge Amplifiers
Increase a transducers signal to measurable levels.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
-
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Converter Signal Amplifier – 0…10 Vdc – DIN Rail
HD978TR4
-
Configurable signal converter amplifier with 0…10Vdc (10…0Vdc) output. Input range -10 ..+60 mVdc. Standard configuration 0…20 mVdc.
-
Product
High-Frequency Signal Amplifier
VCH-605
-
High-frequency signal amplifier VCH-605 is designed to amplify and multiply sinusoidal signals with a frequency of 1-100 MHz.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Amplifiers, Splitters & Combiners
-
DEV’s RF Splitters, Distribution Amplifiers, or Dividers are used to distribute and amplify RF signals, to compensate for signal loss, and to provide redundancy paths to ensure maximum uptime.
-
Product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
Terminal Board
- On-board connector type: 100-pin SCSI-II female- Suitable for Mitsubishi J2 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8132
-
Product
Digital andAnalog Distribution Amplifier
D/A-1
-
The D/A-1 Digital and Analog Distribution Amplifier is a digital and analog signal distribution product based on the the Intelligent Reference/TM-4D™ chassis and is the perfect way to distribute externally supplied signals without the need for multiple units. Most signal distribution products are limited to either analog or digital signals, but the D/A-1 distributes both.
-
Product
Variable Gain Optical Amplifier Module
VGA4700-FM06
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai VGA4700-FM06 series is a next generation variable gain optical amplifier module, which with the most excellent performance and most completes functions in the market. It adopts nowadays most excellent optical performance, most advanced electronic technology and most complete software functions. Remarkable transient suppression control technology and heat management control technology let many complicated optical functions achieved. It is the most versatile multifunction optical amplifier in the market.
-
Product
Fiber Pigtailed Tapered Amplifier
-
The AOSense tapered amplifier (TA) provides a coherent high-power beam, inheriting all properties from the seed source. TA’s are an essential optical component for quantum sciences, such as laser cooling and trapping, cold atom sensors, electromagnetically induced transparency, and quantum spectroscopy. The TA is also used in commercial laser modules, including master oscillator power amplifier (MOPA) lasers and external cavity lasers.
-
Product
16-Channel Bridge Signal Conditioning Unit
ProDAQ 5716
-
The ProDAQ 5716 is a 1U high rack-mountable signal conditioning box for standard 19 in. racks. It provides signal conditioning for up to 16 strain gage or ICP sensors. Either one ProDAQ 3416 16-Channel ADC Function Card or up to two ProDAQ 3424 8-Channel 24-bit Sigma-Delta ADC Function Cards can be connected to the unit.
-
Product
MT Range Broadband Power Amplifiers 80 MHZ - 1000 MHZ
MT Series
-
Class A solid stateBroadband (instantaneous single band): 80 MHz 1000 MHzTypical output power : 100 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 100 W and H < -20 dBc up to 450 MHz andP1dB > 65 W and H < -20 dBc from 450 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to MT 200 possibleReliable, efficient and robust19" Rack3 years standard warranty
-
Product
System Amplifier
SAM100
-
The R&S®SAM100 system amplifier is an ultra-broadband solid state microwave amplifier with a frequency range from 2 GHz to 20 GHz. With a power of up to 20 W, outstanding linearity and very good noise characteristics, the R&S®SAM100 amplifier is ideal as a compact system amplifier in various measurement setups e.g. design (DVT) and product validation test (PVT) or EMC. In measurement environments with R&S generators, frequency analyzers or network analyzers, they can act as drivers or boosters and amplify the measurement signals
-
Product
PCIe Switches And Bridges
-
Modern data centers require solutions that offer maximum performance with minimal power consumption. While compute and storage devices have native PCIe for internal communication, they all use different technologies, such as Ethernet or InfiniBand, to connect externally.
-
Product
High Voltage Amplifier
HA-805
-
*800Vp-p(±400V DC) *200mAp-p(±100mA DC) *Bandwidth: ≦300KHz(400Vp-p) *Slew Rate: 300V/us *Gain(AMPL):0~180(10 Turn VR) *DC Offset: ≦0~±400V(10 Turn VR+SW) *Output Resistor: 100Ω *Microprocess Control Protection
-
Product
Solid State Broadband High Power Amplifier
Model 2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated, and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability, and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. The amplifier is constructed within a single 5RU drawerincluding the forced air-cooling. Available operating voltage configurations are single-phase 220 VAC up to 400 Hz and 28 VDC.
-
Product
RF POWER AMPLIFIERS
BLWA Series
-
A) RF-Sample PortsI) 3x 208 V AC / 60 HzB) External Dual Directional CouplerL) LAN Remote ControlC) IEEE-488.2 GPIB Remote ControlS) Internal RF Switching UnitD) Front Panel RF ConnectorsR) RS-232C Remote ControlE) RF Power Indication (digital)U) USB Remote ControlF) Gain AdjustmentW) Liquid CoolingH) DC SupplyX) External Control of other Amplifiers
-
Product
DR Range Broadband Power Amplifiers 10 KHZ - 400 MHZ
DR Series
-
Class A solid stateBroadband (instantaneous single band): 10 kHz 400 MHzTypical output power : 60 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 40 W and H<-20 dBc up to 250 MHz andP1dB > 25 W and H<-20 dBc from 250 MHz to 400 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
2 GHz to 6 GHz, 45 dBm Power Amplifier
HMC7885
-
The HMC7885 is a 32 W gallium nitride (GaN), monolithic microwave integrated circuit (MMIC) power amplifier (PA) module that operates between 2 GHz and 6 GHz, and is provided in an 18-lead hermetically sealed module. The amplifier typically provides 21 dB of small signal gain and 45 dBm of saturated radio frequency (RF) output power. The amplifier draws 2200 mA of quiescent current (IDD) from a 28 V dc supply. The RF input and output are dc blocked and matched to 50 Ω for ease of use.
-
Product
Low Noise Amplifiers
-
LNA is an outstanding and mature product line of Skylink Microwave. We provide high performance low noise amplifiers in the industry, with reliable and rugged quality. Ultra low noise, ultra broadband and compact size are our specialty and enduring pursuit. Our engineers are committed to satisfying higher custom requirements of our customers and insist on designing optimized products to meet market challenges. Skylink Microwave provides you an extensive line of low noise amplifiers and the most economical choices.
-
Product
Single Channel High Voltage Linear Amplifier
F10A
-
The F10A is a general purpose broadband linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
Solid State Broadband High Power Amplifier 1900 - 6000 MHz / 200 Watts
2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. for EMC, RF Product Test, Communications and Electronic Warfare applications.
-
Product
Small Signal RF/Microwave Power Amplifier
-
R&K’s small signal amplifier series are to amplify various high frequency signals such as CW/Pulsed/AM/FM/N-DCMA/W-CDMA/OFDM , etc.
-
Product
TV Amplifiers
-
PLANAR broadband amplifiers are designed to amplify television signals in the range up to 862 MHz in the forward direction, as well as to transmit internal system signals in the reverse direction in cable distribution networks.
-
Product
Composite 1×6 Video Distribution Amplifier
VDA106
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Separate Amplifier Pressure Sensor
AP-40 Series
-
Separate Amplifier Pressure Sensor. The industry's smallest and lightest air pressure sensor head, weighing only 7g. The super-small sensor head can be mounted close to the detection point decreasing response time.
-
Product
Pulsed Injection Locked IMPATT Amplifiers
-
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
Low Frequency Active Antenna And Amplifier
Type NLF-2
-
A Hot, Active, Noise Reducing Antenna System that will sit on your desk and copy 2200, 1700, and 600 through 160 Meter Experimental and Amateur Radio Signals!
-
Product
Electric Transducer Driver Amplifier
7620
-
The Krohn-Hite Model 7620 is a 17/34 watt, wideband power amplifier that offers extended output power and voltage capabilities. Performance features not available in other power amplifiers, the 7620 provides a differential output and is able to deliver 17/34 watts of continuous power (68 watts at dc) and 141V/282V rms (400V/800Vp-p). It can also provide plus and minus dc voltages simultaneously.
-
Product
Logarithmic Transimpedance Amplifiers
-
Analog Devices translinear logarithmic amplifiers utilize advanced translinear techniques to provide an exceptionally large dynamic range in a versatile and easily used form. Our portfolio relies on proprietary innovations in design and precision laser trimming to achieve the wide measurement range and accuracy in products such as the AD8304 and AD8305. ADI translinear logarithmic amps are used in a variety of applications including optical power measurement, wide range baseband logarithmic compression, the measurement of current and voltage ratios, and optical absorbance measurements.
