Bridge Amplifiers
Increase a transducers signal to measurable levels.
-
Product
Time & Frequency Distribution Amplifiers
-
Brandywine offers a wide range of high quality, state of the art signal timing distribution amplifiers, all with very low phase noise. These precision timing signal distribution amplifiers offer a variety of time and frequency signals and interface formats including IRIG A, IRIG B, Have Quick, 1PPS, as well as low phase noise reference frequencies. All of our distribution amplifiers feature dual inputs with automatic failover and multiple independently buffered outputs.
-
Product
Precision Op Amplifiers (Vos <1mV & TCVos<2uV/C)
-
Analog Devices' broad range of precision amplifiers provides industry-leading support to designers in need of traditional trimmed and zero-drift amplifier technology. Our precision amplifier family helps preserve the accuracy of dc information in an incoming signal with low offset voltage (VOS < 1 mV) and low temperature drift characteristics (TCVOS < 2 V/C).
-
Product
Converter Signal Amplifier – 4…20 mA – DIN Rail
HD978TR3
-
Configurable converter signal amplifier with 4…20 mA (20…4mA). Input range -10 …+60mVdc.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
FTTx Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM’s FTTx amplifiers are designed for PON, RFoG and SFU receiver equipment and are offered in small, plastic QFN packages with integrated amplifier and attenuator functions. All parts cover the full 45 to 1000MHz / 1200MHz CATV band. 5v and 12v solutions are offered with power consumption of ≤ 1.5Watts. MACOM’s FTTx amplifiers are characterized with industry standard photodiodes, covering optical input ranges from -12 to +3dBm and each sample EVK comes complete with a photodiode and APC connector.
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-814
-
The SCS-814 and SCS-815 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-814) and 0.5Hz to 60kHz(SCS-815). Each of the SCS-814/SCS-815's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
Servo Motor Drive
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
Product
Composite 1×24 Video Distribution Amplifier Board
BL-VDA124-01
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Amplifiers
-
Commercial grade indoor distribution amplifier, 54-870 MHz forward gain of 30 dB, 5-42 MHz reverse gain of 20 dB, forward path slope and gain controls with separate reverse path gain control
-
Product
Measuring Amplifiers
VibroMatrix
-
The VibroMatrix measuring system consists of the USB measuring amplifier "InnoBeamer" and various software modules, which can be put together individually. Suitable for your measurement task. All you need is a computer or a notebook. The software enables you to measure in real time and record your data for later offline analysis in the office.
-
Product
Capacitance Bridge
1621
-
The GenRad1621 Capacitance Measurement system is a completely self-contained system capable of capacitance measurements in increments as small as 0.1 aF (10-4 pF) and conductance measurements in increments as small as 100 aU (10-7 U; equivalent to a shunt resistance of 1010 M). Measurements are three terminal, with 2- or 3-terminal connection, and provision is also made for the connection of an external standard for comparison measurements.
-
Product
SW Range Broadband Power Amplifiers 0.8 GHZ - 4 GHZ
SW Series
-
Class A solid stateBroadband (instantaneous single band): 0.8 GHz 4 GHzTypical output power : 18 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 13 W and H < -20 dBc up to 2.5 GHz andP1dB > 12 W and H < -20 dBc from 2.5 GHz to 4 GHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Ku Band Gain Control Amplifier
-
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
Product
Panel-mounted Power Amplifier For Network Simulators
PAV250Bi
-
PAV250Bi is one of the conventional voltage power amplifier model, which is specially designed for R&D of power system simulation.
-
Product
2 Channel Microphone Power Supply and Conditioning Amplifier
SoundConnect 2 mic power supply
-
SoundConnect 2 is a rugged 2-channel USB controlled microphone power supply and conditioning amplifier.
-
Product
Broadband Amplifiers
-
Blonder Tongue Laboratories, Inc.
Blonder Tongue offers a variety of RF amplifiers for broadband CATV or OTA (over-the-air) applications. Be it a 1GHz power doubling two-way indoor distribution amplifier or a mast-mounted preamplifier, or anything in between, we have you covered.
-
-
Product
Optical Limiting Amplifiers
-
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
Product
2-Ch Sensor Amplifier
SR-2210
-
The SR-2210 sensor amplifier accepts constant-current line drive sensors and connects the signal to analyzers and recorders that would not otherwise be compatible with constant-current sensors.The units connects directly with BNC connectors to ONO's model MI-3111 microphone preamplifiers and NP-3000 series of accelerometers.With compact, light-weight, battery operation, it can save for preparation of measurement.
-
Product
Wideband GaN Amplifiers
-
The Teledyne RF & Microwave family of GaN-based amplifiers maximizes power density and efficiency, and establishes a new benchmark for small size in the 0.1 to 6.0 GHz range that operates over multi octave. With dimensions of 2.5"L x 2"W x 0.42"H at only 2.1 cubic inches, these modular, non-ITAR GaN amplifiers maintain the rugged design characteristics needed for harsh airborne and land based requirements.
-
Product
Amplifiers
-
The amplifier is one of the most important components in a pulse processing system for applications in counting, timing, or pulse amplitude (energy) spectroscopy, providing the pulse-shaping controls needed to optimize the performance of the analog electronics.
-
Product
6-Channel VME Pulse Amplifier
V860
-
The V860 is a multichannel pulse amplifier packaged as a standard VME module. It accepts logic-level inputs and generates high-level, very fast positive output pulses.
-
Product
Saluki SE1201 DSP Lock-In Amplifier
-
SE1201 Small-sized Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 50 mHz to 120 kHz. With the high-speed 4-core architecture, high-precision ADC and excellent analog performance, SE1201 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noise. The performance of SE1201 is as good as other lock-in amplifiers brands, even better in some certain parameters, such as measurement accuracy, operating bandwidth, which meets the needs of scientific research and industrial application well.
-
Product
LVDT Sensor Amplifiers
-
Analog Devices signal conditioning ICs, together with linear variable differential transformers (LVDTs), can be used to convert mechanical position to a dc voltage. The IC provides both the excitation for the LVDT and the output conversion to dc level with a user selectable gain. ADI LVDT signal conditioners are available to interface with a wide range of LVDTs, including half bridge and standard 4- and 5-wire.
-
Product
High-Speed System Synchronization and Distribution Amplifier - 3U VPX
Model 5903
-
- Multi-board synchronization with Quartz RFSoC video- Synchronizes up to 64 channels across eight Quartz® boards- Synchronizes sampling and data acquisition for multichannel systems- Provides single sample accurate synchronization between multiple channels and multiple boards- Synchronizes gating and triggering functions
-
Product
Capacitance Bridge
TCB-108
-
Model TCB-108 - Capacitance Bridge is a general purpose bridge for measurement of capacitors, capacitance of transformers and dielectric material. It comprises a transformer-type bridge operating from an internal 108 Hz generator(for accurate measurement at 60Hz) with digital readout of capactiance from 1 pF to 99.999 pF over four ranges and digital readout of D (dissipation factor) in percentage from 0-50%.
-
Product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
-
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
D10-AIO Conversion Set_for Conventional Panel-mounted Type Power Amplifier
PAD24
-
PAD24 DIO(digital input/output)-AIO(analog input/output) Conversion Set Conversion Set products. It could be used for DIO (Digital input/output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and another equipment which need AIO (analog binary input/output, dry contacts).
-
Product
150 kHz-230 MHz Broadband Power Amplifiers
-
Output power up to 80W for standard conducted immunity testing. Our 150 kHz-230 MHz amplifier range covers output power ranging from 20 W to 80 W.
-
Product
Amplifiers
-
Teledyne Lincoln Microwave design and manufacture RF amplifiers utilising the latest semiconductor technology. Our portfolio includes low noise amplifiers (LNA’s), power amplifiers and pre-amplifiers. These can incorporate linearization, filtering, phase and amplitude control functionality.
