Carriers
Carrier devices are practical for adapting your product to a standard interface for testing on the bench or in the chamber.
-
product
Squid PCI Express Carrier Board™ for M.2 and NGSFF (NF1) SSD Modules
Amfeltec Squid PCI Express Carrier Board™ for M.2 and NGSFF (NF1) SSD Modules
-
product
cPCI and PMC Compatible Adapter Carrier
cPCIBPMC3U64ET
By customer request Dynamic Engineering has developed two extended temperature versions of the popular cPCIBPMC design. The design effort included switching to a new bridge to meet the temperature and timing requirements. The new bridge brings new features including the ability to operate the PMC side at a higher clock rate than the cPCI side. The new bridge also has built in features for local address spaces, using the PMC clock in monarch mode for the secondary side, and operating in transparent or non-transparent modes
-
product
Pressure Sensor Kit for Changing Ranges
DP15TL
The wide range of diaphragms furnished eliminates expensive stocking of several transducers and offers the versatility of the differential type bi-directional transducer at a very low cost. The broad line pressure capability of this unit makes it useful in almost every laboratory application from flow to level measurement, vacuum to 3000 PSIG. The high output, when used with a carrier system such as the Model CD15 Sine Wave Carrier Demodulator or the CD12 Transducer Indicator, provides resolution equal to many secondary standard units.
-
product
RF Wideband Downconverter Solution From 100 KHz To 27 GHz
DC27G100
GaGe wideband downconverters are wide frequency coverage receivers that feature a single RF input and 3 standard software selectable IF bandwidths, from 10 MHz to 100 MHz, or 3 optional software selectable IF bandwidths, from10 MHz to 160 MHz. The carrier center frequencies can be tuned from 50 MHz to 27 GHz, using direct digitization below 50 MHz.
-
product
PCIe adapter for PMC
PCIeBPMCX1
Now you can use your PMC with a new PC. The new PC´s have PCI Express connectors in larger quantities than PCI slots. The PCIeBPMCX1 ( PCIe Bridge PMC 1 slot) adapter / carrier converter card provides the ability to install one PMC card into a standard PCIe (Express) 4 lane slot.
-
product
Dual PMC Carrier for 6U CompactPCI
TCP262
The TCP262 supports standard PMC front I/O and CompactPCI rear I/O fully compatible to the TCP260. The PMC slot 2 (upper PMC) I/O lines are connected directly to the CompactPCI connector J5. The PMC slot 1 (lower PMC) I/O lines are connected directly to the CompactPCI connector J3.
-
product
C/Ku Band Satellite Monitoring
SCL-3412
C/Ku Satellite Monitoring System (SCL-3412) is designed to intercept International/national telecom carriers, GSM A/Abis links and IP Carriers over satellite which are using C, Ku, X or Ka-Band. In order to reduce the manual effort and time consumed in the analysis of the carriers, system is integrated with Satellite Carrier Analysis module, which automatically performs the scanning on the selected spectrum and provide the list of carriers along with their payload type (i.e DCME, GSM or IP) and characteristics parameters. This provides great help to take decision for monitoring of the carriers of interest.
-
product
COM Express Type 6 Development Kit
COM Express Type 6 Starter Kit Plus
The Type 6 Starter Kit Plus consists of a COM Express Type 6 module with ATX size Type 6 reference carrier board that offers one PCI Express x16 slot with proprietary pinout for DDI adapter card that convert DDI signal to DP or HDMI signal, one PCI Express graphics x16 slot, one PCI Express x4 slot, three PCI Express x1 slots, Serial ATA, VGA, LVDS, USB3.0/2.0, Gigabit LAN and Super I/O. All necessary cables are included.
-
product
Intelligent Double Sized H009 Interface Module for Excalibur 8000 Family of Carrier Boards
M8KH009
The M8KH009 is an intelligent, double-sized, H009 interface module for the multimode, multiprotocol, EXC-8000 family of carrier boards. The M8KH009 provides a complete solution for developing and testing H009 interfaces and performing system simulation of the H009 bus, according to the standard H009 protocol. Each module of the M8KH009 contains 32K x 16 dualport RAM for Data Blocks, control registers, and Look-up tables. In addition, the module contains another 32K x 16 dual-port RAM for a Concurrent Monitor. All data blocks and control registers are memory mapped, and may be accessed in real-time. Each of the independent, dual-redundant M8KH009 modules may be programmed to operate in one of three modes of operation: Central Control Complex (CCC) mode with Concurrent Peripheral Unit operation (1–16 PUs), Peripheral Unit mode (Multiple – up to 16 PUs) and Bus Monitor mode. In addition, the module can simultaneously operate as an independent Internal Concurrent Monitor in CCC, Multiple PU or CCC/Concurrent PU modes.
-
product
Industry Pack Carriers and Digital I/O
CPCI-4SIP-6U
The CPCI-4SIP-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-4SIP-6U is the perfect solution. There are four (4) Industry Pack sites providing up to 200 I/O pins accessible from either the front panel or the rear back plane.
-
product
Matrix Module For SwitchBlock
The Matrix Module for SwitchBlock is for use with the PXI Carrier Module for SwitchBlock and can operate as an individual relay card, can combine with other Matrix Modules for SwitchBlock in the same PXI Carrier Module for SwitchBlock, and can combine with other Matrix Modules for SwitchBlock in other PXI Carrier Modules for SwitchBlock in the same PXI chassis. Each Matrix Module for SwitchBlock comes in an A-type version, which serves as the first matrix building block and offers row and column access through the front connector, and a B-type version, which serves as an expansion module and only provides column access through the front connector. Typically, SwitchBlock systems contain one A-type module and numerous B-type modules.
-
product
Quality Measurement Tools for Voice, Audio/Visual and Data Payload analysis
PEXQ
PEXQ is OPTICOM’s latest product for Windows offering a complete portfolio of quality measurement tools for voice, audio/visual and data payload analysis based on human perception. PEXQ provides mandatory features in the area of R&D for the development of new multimedia codecs as well as for multimedia equipment manufacturers. Besides lab testing PEXQ is also ideal for network operators and carriers to measure quality of service. PEXQ is founded on well established internationally standardized measurement algorithms such as PESQ (ITU-T Rec. P.862, P.862.1 (narrow band), P.862.2 (wide band); Perceptual Evaluation of Speech Quality) and completely new metrics for video quality testing like PEVQ (Perceptual Evaluation of Video Quality).
-
product
3U CompactPCI Serial M.2/U.2/SATA Storage Carrier
cPCI-A3H20
- 1x NVMe M.2 and 1x NVMe U.2 drive slot- 1x optional SATA 6Gb/s M.2 drive slot shared space with NVMe U.2- Status LEDs on faceplate: drive activity, hot-swap status, user-configurable- Operating temperature: -40°C to +85°C with qualified modules- EN50155 compliant
-
product
3U VPX Flash Storage Module Carrier
FSM-C
Curtiss-Wright Defense Solutions
The Flash Storage Module Carrier (FSM-C) provides rugged, removable, VITA 48.2 compliant, solid state storage in a 1” pitch, industry standard 3U VPX format. By providing a COTS storage solution, the FSM-C can lower schedule and technical risk for embedded storage applications.
-
product
OnyxFX FlexorSet 4-Ch. 250 MHz A/D, 2-Ch. 800 MHz D/A - PCIe
Model 7070-312
Model 7070-312 is a member of the Flexor® family of high-performance PCIe boards based on the Xilinx Virtex-7 FPGA. As a FlexorSetTM integrated solution, the Model 3312 FMC is factory-installed on the 5973 FMC carrier. The required FPGA IP is installed and the board set is delivered ready for immediate use.
-
product
Dual Vapor Gravimetric Sorption Analyzer
DVS Resolution
DVS Resolution’s key feature is the combined ability to precisely control and measure temperature and relative humidity while recording the highest resolution changes in mass. DVS Resolution uses a dry carrier gas typically nitrogen or compressed air for its operation. Digital mass flow controllers regulate flows of dry and saturated gases. Relative humidity is generated by precisely mixing dry and saturated gas flows in desired flow ratios which produce expected relative humidity. In a typical experiment a known concentration of water vapor is delivered over a sample placed inside the sample pan connected to the Surface Measurement Systems Ultrabalance™ measuring realtime mass changes caused by sorption or desorption of water molecules. Prior to sorption measurements, the sample can be in-situ preheated/dried at temperatures of up to 300oC.
-
product
CATV Multi-Carrier Generator
1685
The Model 1685 is a headend / hubsite RF eight carrier generator. Each CW carrier can be activated individually or simultaneously. The RF carriers generated are extremely clean and stable, thus making the 1685 an ideal instrument for testing/aligning the CATV forward band.
-
product
10 Channel ADC FMC Module
ADCFN10-AC – HPC
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN10 is a ten channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides single-ended analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Both AC and DC coupled input are supported. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
product
MIL-STD-1553 MCH
M4K1553MCH
The M4K1553MCH interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M4K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M4K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
product
Quad 250Msps, 16-bit ADC FMC
ADF-Q25
This FPGA Mezzanine Card (FMC) converts four channels of up to 900 MHz analog input bandwidth at 250 Msps and 16-bit resolution. Based on the VITA 57 specification, the ADF-Q25 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
product
AngelShark Carrier Board™ Mac Pro (Late 2013) Cylinder Storage Upgrade by M.2 PCIe SSD
SKU-088-01
How to upgrade storage capacity (the SSD) on a Mac Pro (Late 2013) cylinder?It is possible with the AngelShark Carrier board™ (designed & produced by Amfeltec Corporation, Canada).Carrier board is located internally between the Mac and the original SSD module. It supports any M.2 PCI Express (M-key) SSD modules with standard lengths 2280 and 2260, 22110 (optional).Carrier Board supports x4 PCI Express Gen 3 connection on each M.2 circuit, and it is compliant with PCI Express Specification 3.0 and M.2 Specification 1.1.
-
product
Virtual SBC
What is a virtual session border controller or virtualized SBC? Traditionally, a session border controller (SBC) is a device positioned between carrier networks or between an enterprise LAN and a service-provider WAN. In the latter case, the border controller is called an enterprise session border controller or eSBC. Whether it is delivered as a dedicated hardware session border controller or a virtualized network function, (a.k.a. software SBC) the border controller manages call (session) setup and teardown. The SBC also provides network demarcation (demarc), or separation (border) between network domains, as well as other types of management (control) over the data streams that pass between networks. With the growing popularity of software defined networking (SDN) and the burgeoning market development and adoption of network function virtualization (NFV), eSBC functionality is more and more often de-coupled from a dedicated hardware device and delivered as a virtual instance running as a virtual machine (VM) on top of a hypervisor. It is generally not well understood in the market why an eSBC is such a critical network element for a secure and reliable SIP-based enterprise phone system. The following publication will help close that knowledge gap.
-
product
Gamma Detectors
In Gamma detectors, the gamma radiations produce electrons by interacting with the cathode material and the filling gas.These electrons ionize the gas and the charge carriers are collected by the electrodes. The resulting anode pulse is detected by a load circuit. The primary electrons are created by several interaction mechanisms:- Photoelectric effect- Compton scattering- Pair production
-
product
PC/104 OneBank Carrier
EMC²-SoM
Sundance Multiprocessor Technology Ltd.
The EMC²-SoM is a PCIe/104 OneBank™ Carrier for a Trenz compatible FPGA and SoC Module and has expansion for a VITA57.1 FMC™ LPC I/O board. It also has I/O pins, using a 100-way Samtec RazorBeam connectors system, the “Sundance Expansion Interface Connector” (SEIC) can be customize for individual applications and bespoke connectors.
-
product
PMC-to-4X PCI Express (PCI-e/PCIe) Adapter
6778
The Technobox, Inc. P/N 6778 is a PCI Express (PCIe/PCI-e) carrier that permits the insertion of a single PMC into a PCI-e slot (4X). The adapter orients the PMC in a reverse manner such that the rear I/O from PN4 appears at the 68-pin SCSI-style connector installed on the adapter’s bracket. Furthermore, the reverse orientation of the card permits direct access to the standard front I/O (if any) within the host chassis.
-
product
cPCI IP Carrier Module With Front And Rear I/O
DP-cPCI-5211
DP-cPCI-5211 IP carrier board provides electrical and mechanical interface for four industry standard IP modules. The board provides full data access to the IP modules I/O, ID and memory spaces. The programmable registers are used for configuring and controlling the operation of IP modules.
-
product
Compact Carrier Board
CM22002
LinkedHope Intelligent Technologies Co.,Ltd.
CM22002 is a compact carrier board which matches the dimensions of a COM Express® Basic module.CM22002 is ideal for space constrained applications, and supports extended temperature ranges of -40℃ to +85℃.
-
product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for six M.2 or NGSFF (NF1) PCIe SSD Modules
SKU-086-36
This Squid PCIe Carrier board can support up to six M.2 or NGSFF (NF1) PCIe SSD (solid state drive) modules, with M-key. Supported module dimensions are 2280 or 22110 in length, and a width of up to 32 mm. SSD modules of any capacity may be used, from any vendor, and in any combination.
-
product
3rd Gen MicroTCA Carrier Hub (MCH), Double Module, 40/10GbE/PCIe/FPGA/SRIO
UTC006
The VadaTech UTC006 is a double module, MTCA.4 format, MCH with front-panel fabric expansion and RTM support (PCIe optiononly). Fabric options include PCIe Gen3, 10/40GbE, Xilinx Virtex-7 FPGA, Cross Bar Switch (CBS), and SRIO.
-
product
SMARC
SMARC (Smart Mobility Architecture) modules are ultra-small system-on-modules targeted towards applications that demands compactness and energy-efficiency. The SMARC system-on-modules also support Axiomtek evaluation carrier boards for easy integration and hardware design reference.
