-
Product
Modbus Data Acquisition
-
The Datexel range of Data Acquisition equipment includes Modbus RTU Masters and Slaves, Modbus Input, Modbus Output Modules, Modbus Isolation Modules and Modbus Repeaters. The range also includes converters (RS485, USB, RS232, RS422, TCP-IP). By combining these units with the DAT3000 and DAT10000 series a complete solution for your Data Acquisition can be found from Datexel. The DAT9550 is a remote Modbus display unit that can be programmed to accept data from Modbus slaves or masters such as a PLC or the DAT9000 range of Modbus controllers.
-
Product
4-Channel High Speed Position Comparison and Trigger Module
ECAT-TRG4
Trigger Module
The ECAT-TRG4 is EtherCAT slave module with high-speed position comparison trigger and encoder single redriver function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications.
-
Product
Precision Time Protocol
IEEE-1588
-
Meinberg Funkuhren GmbH & Co. KG
As a high-stability Grandmaster Clock in IEEE 1588-2008 networks, the MEINBERG NTP time servers with highly accurate PTP clients ("slaves", such as the PTP270PEX or PTP SYNCBOX ) At the same time as the current absolute time.
-
Product
Master-Slave Distributed Motion & I/O Master Controller
PCIe-7856
Controller
The PCIe-7856 is a PCI Express interface card providing two ports for Motionnet and HSL systems for distributed motion and I/O in machine automation applications. HSL technology allows thousands of I/O points to be scanned at the millisecond-level in real time by using a master-slave architecture.
-
Product
PXI General Purpose 2A Relay Module 16xSPDT, 50 D-sub
40-131-001
Relay
These low cost, general purpose electromechanical relay cards are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 50 pin D-Type connector plug.
-
Product
PXI 5A Power MUX, 8-Bank, 5-Channel
40-651-004
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Modbus Register Converter
Model 2390
-
* Converts Modbus Registers and variables for replacement Modbus devices.* Maintain existing software when upgrading Modbus systems.* Provides serial control of Modbus RTU devices from any ASCII source.* User defined Register Conversion Table supports all Modbus RTU devices.* Internal Register Conversion Tables for Watlow F4-to-EZ-ZONE and F4-to-F4T conversion.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes baud rate conversion capability.* Uses SCPI commands to load the Conversion Table and set serial settings.* Small metal case mounts on a DIN rail or on any flat panel.* 239x Table Loader Program uploads the 2390 Register Conversion Table from an Excel csv file.* 239x Serial Keyboard Program provides instant control of the 2390 and Modbus Slave Devices without writing a program.
-
Product
PXI 5A Mux 8-Bank 5-Ch Isolated COM
40-651-014
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Dial Up Modem Test
ModemTest 1.3
-
Test your dial up modem and telephone line for errors and connection speed. A local loopback test is provided as well as a master / slave test. The master / slave test requires 2 modems and 2 telephone lines. ModemTest is compatible with most dial up modems. (9.6 - 56Kbits)
-
Product
PCI Express to VME interface
SIS1100e/3104
-
Single width 6U VME master/system controllerred ball, 1/2/4 GBit/s optical link, red ball, up to 450 m link distance, red ball 128 MBytes memory (PPC Ethernet or VME slave)
-
Product
Single 4x4 1-Pole 16 Amp PXI Power Matrix With Loop-Thru
40-552-011
Matrix Switch Module
The 40-552 range of 16 Amp PXI power matrix modules is available in four configurations with matrix sizes of 8x2 and 4x4 and the ability to expand the matrix size with the Y-Axis loop-thru connections: e.g. 8x4, 12x4, 16x4, etc. (with 4x4 matrices) or 16x2, 24x2, 32x2, etc. (with 8x2 matrices). This range is capable of switching up to 16 Amps and up to 300VDC/250VAC hot switching and 400VDC/250VAC cold switching. These PXI power matrix modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors, and solenoids.
-
Product
PXI 5A Mux 4-Bank 11-Ch Isolated COM
40-651-013
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Wire Harness Tester
Panther4HT Master- Slave DSU
-
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.
-
Product
PXI 8x4 Power Matrix, 2 Pole
40-550-002
Matrix Switch Module
Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current. These modules are fitted with electro-mechanical power relays, gold-flash over silver alloy. A spare relay is built onto the circuit board to facilitate easy maintenance with minimum downtime.
-
Product
Exerciser with SMBus Support
Summit Z3-16
-
The Summit Z3-16 with SMBus Support is a critical test and verification tool intended to assist engineers in developing and improving the reliability of their systems. The Summit Z3-16 with SMBus Support can emulate PCI Express root complexes or device endpoints, allowing new designs to be tested against corner case issues. In addition, it can emulate SMBus traffic as a master or slave.
-
Product
PXI Multiplexer, Very High Power DC, 4-Channel, 20A, 28V
40-664A-002
Multiplexer Module
The multiplexer is suitable for switching heavy loads or for slave switching large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of DC voltage at high current.
-
Product
LAN (2ch) Expansion Board (supporting EtherCAT)
OP-SB89E
-
OP-SB89G is an expansion board for Ethernet LAN which is to be inserted into a slot of portable communication analyzer (LE-8200A/LE-8200). It has 4 LAN measurement ports and you can sniff 2 Ethernet lines at the same time by tap connection to capture packets on the 2 lines. It also can monitor input/output of a EtherCAT slave and measure the time delay cased by the slave.
-
Product
PXI 5A Power MUX, 1-Bank, 48-Channel
40-651-001
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel 4-bank. 11-channel 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Local Bus Master & Target Bridges
PCI 9052
-
The PCI 9052 PCI I/O Accelerator provides low cost connectivity for PCI slave designs. It is specifically targeted at easing the transition of existing ISA designs to the more feature rich and performance oriented PCI bus.
-
Product
PXIe-8522, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module
787312-01
Ethernet Interface
PXIe, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8522 is a 1000BASE-T1 unshielded twisted pair (UTP) module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications that require Automotive Ethernet to test … and validate automotive electronic control units (ECUs). The PXIe-8522 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8522 also provides LEDs on the front panel to help you monitor the network link and activity.
-
Product
AT Command Master+Slave / Central+Peripheral
AT command module serie
-
Raytac's AT command module series comes with AT command firmware pre-programmed which helps developers enjoy a Design Saving & Time-To-Market journey.
-
Product
PMC Module
PMC-DA816
PMC Module
The PMC-DA816 is a slave Digital to Analog boardthat is managed by the host processor on the PMCbus. The card contains a state machine that performsmost of the work of outputting data, in order tominimize the impact to the HOST system.The PMC-DA816 is supported by ALPHI Technologyunder Windows NT by a Board Support Packagewhich is supplied with the card. Other documentationsupplied with the card will describe this support in fulldetail.
-
Product
Real-Time Ethernet Master/Slave Network
EtherCAT
-
EtherCAT is an open real-time Ethernet Master/Slave network developed by Beckhoff. Today, it is an open standard, managed by the EtherCAT technology group. EtherCAT sets new limits for real-time performance since it processes 1000 distributed I/O in 30 µs or 100 axis in 100 µs using twisted pair or fiber optic cable. Regarding topology, EtherCAT supports a simple low cost line structure, a tree structure, daisy chaining or drop lines - no expensive infrastructure components are required. Alternatively the classic more expensive switched star topology can be used.
-
Product
MTM-Bus Tester
PXIe-1149.5
BUS Tester
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
Product
16-CH Discrete Input 16-CH Discrete Output Daughter Board Module
HSL-DI16DO16-DB-NN
Strain/Bridge Input Module
- Slave ID consumption: 1 16-CH NPN sinking type sensor inputs or dry contact and 16-CH - NPN sinking type outputs- Photo couple isolation voltage: 2500Vrms- Input impedance: 4.7KΩ- Input current: ??10mA(Max), ??12.5mA(Peak)- Input voltage: ??40V (Max)- Output switching capacity:300mA/ch at 24VDC- Terminal Base:HSL-TB64 or HSL-TB32-DIN- LED indicator: Power, Link and I/O status
-
Product
Electrical Safety Test Scanner
19200
-
Support Electrical Safety Test Scanning Support High / Low voltage circuit insulation (Switch module)Support 8 slots for plug-in (removable)Max. 9 slaves for multiple scanners (master/slave interface)Standard RS-232 and USB interface Optional GPIB interface CE Mark19200 can be installed in Chroma Electrical Equipment ATS model 8900
-
Product
PXI 5A Mux 2-Bank 24-Ch Isolated COM + Ind Isolation
40-651-112
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
PXI 16 x SPDT Reed Relays
40-110-021
Relay
The 40-110/115 range of switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. General purpose reed relays are used for the construction of small switching networks or for slaving up to larger switches.To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
Product
PXI General Purpose 2A Relay Module 26xSPDT
40-131-201
Relay
These are low cost, general purpose electromechanical relay cards capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
Product
IVN-8561, Automotive Ethernet Interface Device
786169-01
Ethernet Interface
2-Channel, 4-Port, 100BASE-T1 to 100BASE-TX Automotive Ethernet Interface Device—The IVN-8561 is an interface that converts 100BASE-T1 unshielded twisted pair (UTP) automotive Ethernet to standard 100BASE-TX Ethernet. It is ideal for developing applications that require automotive Ethernet to test and validate automotive electronic control units (ECUs). The IVN-8561 provides two channels to convert data between 100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet. Each 100BASE-T1 port can be configured as master or slave, using switches on the front panel. The IVN-8561 also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
