Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
Pressure Measurement Accessories
-
Pressure subbers, connector bushings, grommets, pipe and tube fittings, tube by length, pressure cooling element, pressure and force cables and connectors, air line lubricators, and air filters.
-
Product
Connector and Breakout Box
ES4640
-
The ES4640 Connector Box offers a standardized wiring and connectivity for HiL testing systems in the powertrain domain. Its front panel provides connectors for the ECU, CAN bus communication, on-board diagnostics, and LEDs for ignition and injectors. Its rear panel connects loads, failure simulation, and other components. Sample applications of the ES4640 are closed loop HiL systems for 8 cylinder gasoline and diesel engine ECUs.
-
Product
PXI 50 x Normally Closed Relay 1A 60W
40-145-001-NC
Relay
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector.
-
Product
Cable Tester
LW3310
-
Dongguan Longwei Electronic Technology Co., Ltd.
LW3310 wire tester is designed for all kinds of electronic wire, electric wire and connector design, due to the various types of wire and connectors used in every field, this applies only to the commonly used wire detection instrument. Widely used in computer, communication, medical, electrical appliances, motor, automobile and other wiring test.
-
Product
LXI Microwave Multiplexer, SP4T, 7-Bank, 18GHz, 50Ω, SMA
60-803-107
Multiplexer Module
Our 60-803-107 is a 7 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-316-HI
Programmable Resistor Module
The 40-230-316-HI (PXI) and 42-230-316-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 1.8kΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Connector Test Tools
-
Yokowo Connector Test Tools - BtoB Clips, Interface Connectors, and Tools for FPC Connectors
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 50 GHz, 50 Ω, SMA-2.4, Remote Mount, Failsafe
42-780B-551-E
Relay
The 40-780B-551-E (PXI) and 42-780B-551-E (PXIe) are single failsafe SPDT 50 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
Cable, 96-Pin Female, Screwlocks To 100-Pin Male, Screwlocks, 1.27mm Pitch, 0.5m
A096SFR-100SMR-5A050
-
The 96-Pin to 100-Pin 1.27mm Pitch Adaptor Lead is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. M2.5 screwlocks are provided on the 96-Pin connector and 4-40 UNC screwlocks on the 100-Pin connector.
-
Product
RTM Sensor Signal Conditioning Board
MS 3631I
-
CPCI Rear IO Sensor Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on LAOA, RAOA, AOSS (2), DCM (3), PCS (3), RSA (5) & ASA (4) and TAT sensor interface. This card shall handle excitation, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
Product
High Power Combiner Divider, 100 Watts Way, N Type, IP67 Outdoor, 698 - 2700 MHz
PD9026
-
INSTOCK Wireless Components, Inc
PD9026 is an outdoor, waterproof and weather resistant, IP67 rated, 2 way, 50 ohm, broadband RF high-power power combiner furnished with type N female coaxial connectors. All wireless band frequencies in the range from 698 to 2700 MHz are covered with best in class RF performance. Max microwave input power levels to 100 watts can be handled in power divider splitter applications. For non-coherent signals, up to 20 watts can be handled through each port. With coherent signals, up to 50 watts can be handled through each port. See 2 way high power combiner input rating tables for more info.
-
Product
3U VPX 6 Slot Power & Ground 10G Pass Through
101VPX306P-9X12R
-
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
Product
ATCA Test Extender with Zone 3
114EXT8040-0XXX
-
The ATCA extender board extends both the power and IPMB signals. It is designed for the full populated fabric slot (5 ZD connectors, P20 thru P24) and the power connector J10.
-
Product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Unterminated, Tinned Ends, 2m
A025CFR-T-5A200
Cable Assembly
This 2m long female 25-Pin Micro-D to unterminated (with tinned ends) cable assembly is constructed from 18/0.1 (26 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connector to its associated product.
-
Product
Coaxial Switch, DC to 4 GHz, SPDT, 75 Ohms
8762F
-
The Keysight 8762F brings a new standard of performance to 75-ohm coaxial components. Designed for ATE switching systems, the Keysight 8762F offers the performance demanded by the cable television distribution equipment and communications equipment industries. It gives the ATE system designer of telecommunications and cable distribution equipment the tools to design reliable, high performance switching interfaces. The Keysight 8762F uses a mini 75-ohm SMB connector for the coaxial interface. The mini 75-ohm SMB connector is designed to terminate RG-179 75-ohm coaxial cable. The Keysight 8762F is designed to work in virtually any system due to the range of voltage options covering 4.5 V to 30 Vdc available for activating the switch solenoids. The standard configuration of the switch includes solder terminals.
-
Product
RF Connector
-
Electrical connector designed to work at radio frequencies in the multi-megahertz range. RF connectors are typically used with coaxial cables and are designed to maintain the shielding that the coaxial design offers.
-
Product
Additional Products: 500 Pin SEARAY Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
SCB-68A, Noise Rejecting, Shielded I/O Connector Block
782536-01
Terminal Block
68-Pin Female Screw Terminal to 68-Pin Female D-SUB, DIN-Rail, Shielded I/O Connector Terminal Block - The SCB-68A provides a shielded I/O connection for interfacing I/O signals to plug-in data acquisition devices with 68-pin connectors. This Terminal Block combines with shield cables to provide low-noise signal termination. The SCB-68A incorporates a completely redesigned mechanical enclosure with a magnetic removable lid, DIN-rail mount compatibility, and a resettable fuse. It is compatible with single- and dual-connector Multifunction I/O with 68-pin connectors. The SCB-68A also includes two general-purpose breadboard areas and an onboard cold-junction compensation sensor.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 0.5m HV, Exit Towards Pin 1
A050DF5-T-HA050
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-144-HI
Programmable Resistor Module
The 40-230-144-HI (PXI) and 42-230-144-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 1.5MΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V
CPCI-7500
-
*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS
-
Product
Calibration Kit
N611
-
*N611 Calibration Kit, * Frequency Range: up to 6 GHz, * Impedance: 50 Ohm. * Connector Type: N-type.
-
Product
PXI 8x2 RF Matrix 1.5GHz 50 SMA
40-750-521
Matrix Switch Module
The 40-750-521 is an 8x2 RF Matrix Module suitable for switching frequencies up to 1000MHz. It has a 50Ω characteristic impedance with front panel mounted SMA coaxial connectors. The matrix intended for the easy construction of high performance bidirectional switching systems.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 1-Bank 18GHz SMA
60-801-201
Multiplexer Module
The 60-801-201 is a 6-channel, 1-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
Mini Array+
DORC's ZX-1
-
Direct Optical Research Company
Used primarily to measure multi fiber (MT/MPO and MT-RJ) connectors, DORC's fourth generation "ZX-1 mini Array+" is the result of 18 years of hardware and software product development. Although optimized for mutifiber connectors, the ZX-1 mini Array plus also does an excellent job of measuring single fiber PC and APC connectors. DORC's patented design is based on a variant of the Michelson configuration, and provides BOTH 2D and 3D high resolution images of the sample under test in approximately 45 seconds for multi fiber connectors and just 3-4 seconds for single fiber connectors - from the time the connector is inserted.
-
Product
1Gsps, 18 Channel, Logic Analyzer with Protocol Analyzer plugins and Hardware Compression
DigiView™ DV518
-
- Physical Channels: 18- Sample rate: 4ch@1 Gsps or 9ch@500Msps or 18ch@1Gsps (4 ch. are sampled every 1ns or 9 ch. are sampled every 2ns or 18 ch. are sammpled every 4ns)- Typical capture: 100M transitions (> 1B samples)- Hardware based triggers with 8 universal match circuits, and partitionable 16 stage sequencer- Adjustable Threshold (± 4V)- Real-time, Hardware-based, Adaptive Compression- Channels protected to ± 20V- Ground leads protected to ± 12V- High-quality test leads: 66 strand soft copper wires, flexible insulation, and gold plated connectors. Fit .025 square posts as well as the included clips.- Extra ESD protection- Streaming storage with auto fall-back to Store & Forward mode ensures large storage and reliability.- USB 3.0 (SS) or USB 2.0 (High Speed)- USB powered- Each DigiVIew includes all avialable Protocol Analyzer plugins (including: I2C, SPI, CAN, Async, Sync, 1-wire, I2S, TDM)- Free Plugin Developers' Kit- Requires Windows 7 or greater OS (32bit or 64bit)- Free Lifetime sofware updates.- 1 year warranty
-
Product
Universal Multichannel System up to 15 kV
-
- Up to 16 high voltage channels- 15 kV maximum output voltage- Maximum Current 1 mA- CPE, Radial Multipin or Kings connectors- Available with either positive, negative or mixed polarity- Up to 1 nA /100 pA current set / monitor resolution- Up to 200 mV/10 mV voltage set / monitor resolution- Low Ripple, down to < 10 mVpp- 2 different channel grounding - Common Ground (AGxxxx) - Common Floating Return (Axxxx)- Independently programmable for each channel: - Output voltage - Current limit - Ramp up/down (1 ÷ 500 V/sec) - TRIP parameter- Current generator operation in over current condition
-
Product
96-Pin 1.27mm Pitch Connector Backshell Kit
C096SGR-4BO-5A
-
This backshell is designed for use with the 96-Pin 1.27mm pitch connector. For use with connectors that make a direct connection to a corresponding Pickering Switching Module.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 36", 8 20-Pin Ribbon Cable Connectors
540160010240
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 36", 8 20-Pin Ribbon Cable Connectors
-
Product
Enclosures
-
VPC offers a variety of options to customize standard enclosures to meet any application need. Use VPC's Customer Wirelist Template to quickly communicate your overall requirements. VPC can provide options such as cutouts, secondary connectors, silk screening, engraving, and much more. Contact a Field Application Engineer for assistance designing a custom enclosure to meet your test needs.
