Conductivity
-
Product
Outdoor Infrared Motion Sensor
ENVIROMUX-IMD-O
-
Outdoor weatherproof - high reliability against water and insects. Double conductive shielding to eliminate false alarms from light sources. Registers movement in the area covered: 40 ft (12 m) x 50 ft (15 m) - 120° wide. LED lights during detection. Selectable detection paterns: Multi-Level (40 zones) or Pet Alley (18 zones). Unwanted detection areas can be eliminated using the included area masking strips. Selectable Sensitivity: High, Mid and Low. Adjustable to the brightness of surrounding environment with the Day/Night Mode switch. Tamper switch opens when cover is removed. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: -4 to 122°F (-20 to 50°C). IP54 compliant. Powered by ENVIROMUX-2D/5D/16D.
-
Product
Thermitest
THW-L2
-
Designed with speed and operational simplicity in mind, the Transient Hot Wire (THW-L2) Liquid Thermal Conductivity Meter is an advanced measurement system for direct determination of the thermal conductivity of liquids and pastes in accordance with ASTM D7896-19. In less than 2 seconds, a single measurement of small volumes of liquids and pastes can be accurately and precisely measured for thermal conductivity. Using a non-stationary measurement approach, the THW-L2 uses rapid test times to limit convective effects for samples with a wide range of viscosities. The THW sensor consists of a 60 mm heating wire that is fully inserted into an isothermal sample. A constant current source (q) is used to heat the sensor wire and the temperature rise is recorded by monitoring the change in electrical resistance of the wire. The slope (m) is determined from the plot of temperature rise vs. logarithm of time and is used in the calculation of thermal conductivity (λ). Liquid samples of high thermal conductivity will have a lower slope, while liquid samples with low thermal conductivity will have a higher slope.
-
Product
VPX Extender 3U VITA67.1 Conduction Cooled
1940000519-9001R
-
3U VPX Extender for conduction cooled boards mounted in conduction cooled chassis VITA 67.1 (VITA 67.1 connectors not included)
-
Product
Automotive Supply Simulation System
-
Spitzenberger & Spies GmbH & Co. KG
The modularly constructed Automotive Supply Simulation System is a compact EMC-Test System for the execution of immunity measurements for pulse-shaped, line conducted disturbances at electronic equipment of motor vehicles. The high performance version enables tests of current-intense consumers or even complete vehicles
-
Product
Handheld Digital Thickness Gauges
HC-210
-
Shenzhen Chuangxin Instruments Co., Ltd.
HC series of coating thickness gauge is a portable thickness gauge with eddy current thickness method and electromagnetic thickness method. It can be used to quickly and accurately measure the thickness of coating or cladding material without damaging it. As an essential instrument for professional material protection, this coating thickness gauge is widely used in manufacturing industry, metal processing industry, chemical industry and commodities inspection etc., both in the laboratory and in the engineering field. It can measure the thickness of nonmagnetic layer on magnetic metal substrate condition (such as steel, iron, alloy and hard magnetic steel, etc.) and the thickness of conductive layer on nonmagnetic metal substrate condition (such as rubber, paint, plastic, anodic oxidation film, etc.).
-
Product
Emergency Conditions Testing
-
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
Product
Human Potential Measuring Instrument
KSD-4000 / KSD-4100
-
Electronic devices and metal tools carried by workers have individual capacitance to ground and are charged at human potential. When the charged electronic device touches the ground or a metal tool touches the electronic device, a transient current with a high peak current flows at high speed, Causing A Failure. By Using The Human Body Potential Measuring Device, The Potential Of The Human Body Can Be Measured Accurately, And It Can Be Immediately Determined Whether Or Not The Electronic Device Is Damaged By The Potential. You Can Also Find Out How Much Static. .. .electronic meters such as conductive floors, electrostatic mats, electrostatic shoes, and wrist straps reduce the human potential.
-
Product
8-Channel 250 MHz A/D with DDC, Kintex UltraScale FPGA - XMC
Model 71131
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Powerful Xilinx Kintex UltraScale FPGAs- Eight 250 MHz 16-bit A/Ds- Eight multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction cooled versions available
-
Product
Ultrasonic Sensors
-
Chemically resistant ultrasonic sensors measure fill levels without contact both under normal pressure and at an overpressure of up to 6 bar in tanks and containers. Through the combination of switching and analog output, you can even conduct fill-level and overflow protection simultaneously.
-
Product
Electronic DC Load, 80V, 80A, 400W With/without Remote Interfaces
LD400 Series
-
Versatile solution for testing dc power sourcesConstant current, resistance, conductance, voltage and power modesWide voltage and current range, 0 to 80V and 0 to 80A400 watts continuous dissipation at 28°C (360W at 40°C)600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of <1V at 40AHigh resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminals (front terminals 30A max.)Full bus control via USB, RS232 and LXI compliant LAN interfaces (LD400P)GPIB option (LD400P only)
-
Product
Monitoring
-
Parker offers a broad range of onsite and laboratory solutions for monitoring, evaluating, and testing a wide variety of substances, from water and hydraulic oil to fuel and various gases, for conditions ranging from insolubility and viscosity levels through flow rate, conductivity, and pressure. They are suitable for use in industrial, marine, and numerous other applications.
-
Product
Electromagnetic Interference Test
-
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
Product
Aluminum PCB
-
The heat dissipation afforded by this construction is dramatically superior to standard FR-4 constructions. The dielectrics used are typically 5 to 10 times as thermally conductive as conventional epoxy-glass and a tenth of the thickness resulting in thermal transfer exponentially more efficient than a conventional rigid PCB. This is so effective that lower copper weights than suggested by the IPC heat-rise charts can be used.
-
Product
Specialist Inline Inspection
-
NDT Global treats each pipeline individually from the offset. Before a project even begins, a feasibility study of the pipeline detail is conducted by NDT Global, to determine the appropriate tool and required modifications to complete the inspection. NDT Global has an extensive engineering capability in this regard and has a proven track record in providing tailored solutions to deal with a wide variety of pipeline characteristics.
-
Product
Software Compatibility Testing Services
-
ImpactQA uses compatibility testing to ensure interoperability between your business-critical systems to discover important modifications or additions required. Following functional necessities, we offer solutions so that our clients could avoid loss of reputation and financial risks caused by poor system compatibility. Testing conducted before the product releases identify compatibility glitches and controls project budget over the prescribed limits. ImpactQA offers an end to end compatibility testing services and infrastructure to make sure your apps deliver for your users and your business.
-
Product
2-Channel Front End
BEQ II.1
-
*Binaural, digital equalizer with 24 bit technology and USB interface.*The digital equalizer BEQ II.1 combines the characteristics of an equalizer, a two-channel front end and an A/D converter into one mobile and very versatile measurement tool.*Binaural, aurally-accurate recordings can be conducted easily with BEQ II. The AES/EBU interface allows a quick and easy expansion into a four-channel system, e.g. with the HMS III or HMS IV. Via the ADAT interface, up to four BEQ II units can be connected, allowing for eight-channel recordings.*Integrated signal conditioning allows common measurement sensors (Microphone, Line, ICP�) to be directly connected to the front end. In addition, separate pulse inputs are available e.g. for RPM data acquisition.*Thanks to the high-performance built-in battery - external DC power supply is also possible - and its low weight, BEQ II.1 is the ideal tool for either mobile or stationary operation.
-
Product
PRO 3-in-1 pH, EC, TDS Combo Meter
MW802
-
This Milwaukee 3-in-1 combo meter allows you to measure pH, EC (conductivity) and TDS with a single meter and one single probe.
-
Product
Conductive Anodic Filament Testing
AutoCAF2™
-
AutoCAF™ is able to measure up to 256 individual measurement sites under conditions of high humidity and temperature in accordance with IPC-TM-650 2.6.25 Test Method & IPC 9691 CAF Test Users Guide.
-
Product
Glow Wire Test Apparatus
GWT A2
-
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
Product
Interface
RQVME2-1553
Interface
The RQVME2-1553 provides new levels of performance and flexibility for MIL-STD-1553A and B Notice II on the VMEbus. Available in commercial, industrial and conductively cooled versions with one, two or four dual-redundant channels, the RQVME2-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
Seismic Transducers Calibration System
-
Calibration of the seismic sensors should be conducted in the low-frequency domain, which means, that the relative method used for calibration of the vibration transducers is not applicable since it does not guarantee the required accuracy level. The problem is that the reference accelerometers have uneven AFR characteristic in the low-frequency domain. Thus, calibration of seismic transducers requires implementation of a different approach.
-
Product
Test Adapter
cPCI/VME/VME64x
-
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly. Usually the test adapter includes fields for voltage and amp, current measurements and in some cases also some pins for wire wrap to conduct custom connections.
-
Product
Immersion Fittings
-
Specialized, rugged holders designed to secure sensors (pH, ORP, conductivity, dissolved oxygen) directly into tanks, open vessels, basins, and channels for real-time monitoring.
-
Product
Oxygen / Nitrogen / Hydrogen Analyzer
ELEMENTRAC ONH‑p 2
-
The new ELEMENTRAC ONH-p 2 is a powerful and robust elemental analyzer for measurement of oxygen, nitrogen and hydrogen concentrations in inorganic materials like steel, iron, copper or ceramics. The highly sensitive NDIR and thermal conductivity detectors reliably detect element concentrations from low ppm content to high percentages.
-
Product
Syscal Deep Marine
-
In fresh water environment, the standard Syscal Pro can be used for marine resistivity profiling. However, in highly conductive environment, a modified variant with higher current output is required.
-
Product
Starter Pen Meters
-
precision is now available in a line of pen meters that provide accurate measurement of pH, oxidation-reduction potential (ORP), conductivity, salinity, and total dissolved solids (TDS).
-
Product
PCB Systems Vibration and Acceleration Simulation Solution
Xpedition
-
As the industry’s market share leader in PCB design software, the Mentor Graphics® Xpedition product augments mechanical analysis and physical testing by introducing virtual accelerated lifecycle testing much earlier in the design process. This is the industry’s first PCB-design-specific vibration and acceleration simulation solution targeting products where harsh environments can compromise product performance and reliability, including the military, aerospace, automotive and industrial markets. Traditional, physical HALT (highly accelerated lifecycle testing) is conducted just before volume manufacturing, and requires expert technicians, which can result in costly schedule delays. Bridging mechanical and electronic design disciplines, the Xpedition product provides vibration simulation significantly faster than any existing method. This results in increased test coverage and shortened design cycles to ensure product reliability and faster time to market. The Xpedition component modeling library is the most extensive in the industry, comprised of over 4,000 unique 3D solid models which are used to create highly defined parts for simulation. The 3D library allows users to easily match geometries to their 2D cell database. Designers can assemble the parts models on board and automatically mesh them for performance analysis, including stiffeners and mechanical parts. The system modeling tool is ultra-fast since it can model over 1,000 components per minute.
-
Product
TDS/Conductivity And PH Testing Instruments
DS & pDS Meters™
-
No water supply is completely pure. Every industrial, commercial, or natural source contains dissolved solids or salts. These impurities contribute to scale, corrosion, poor taste, and environmental pollution that endanger animal and plant life. Myron L® Company has two proven ways to measure such impurities. Our DS Meters™ provide fast, accurate, on-the-spot measurements of total dissolved solids (TDS) or conductivity. pDS Meters™ test conductivity or TDS, plus pH. Readings from their highly stable circuitry help assure product quality, prevent equipment damage and verify in-line instrumentation in a wide range of applications.
-
Product
Battery Conductance Tester
FST-8000
-
Foresight Electronics Co., Ltd.
Profsional battery conductance tester for Lead-acid stationary (wet, flooded, gel, AGM, VRLA) battery cells/blocks, to measure actual capacity and aging for UPS, telecom, industrial, vehicle, solar or other applications' small and large battery banks.Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds.
-
Product
Surface Resistance Meter Kit - Test Anti-Static, Static Dissipative and Conductive Surfaces
PRS-812RM
-
- Surface Resistance Tester from 0.10 Ω to 1 Teraohm- Constant Voltages 10 volts and 100 volts- Automatic Electrification Period- Determines if a surface is Dissipative, Conductive, or Insulative- Measures resistance point-to-point(Rtt) and resistance to ground (Rtg)- Measures resistance of ESD Flooring, ESD Worksurfaces and Packaging- Conforms to all ESD Association Standards for Resistive Characterization- Includes 2 each Surface Resistance Probes- Packaged in a hard shell Carrying Case- Certificate of Calibration Traceable to NIST included- 2-year Limited Warranty on Main Instrument
