Filter Results By:
Products
Applications
Manufacturers
-
product
Ultrasonic Fatigue Testing System
USF-2000A
The USF-2000A implements materials fatigue testing at 20 kHz. Consequently, it is possible to evaluate 109 to 1010 order fatigue strength, where it had been difficult to obtain data before. Also, data for 107 cycles can be obtained in about ten minutes.
-
product
Spring Fatigue Testing Machine
TPJ Series
Jinan Testing Equipment IE Corporation
Model TPJ Series Mechanical Computer Control Spring Fatigue Testing Machine is mainly used for the fatigue properties of all kinds of coil springs, disc springs, shock absorbers, and seal springs etc. The Spring Fatigue Testing Machine consists of motor, reducer on the connecting cams to drive the connecting rod and make reciprocating motion achieve the compression fatigue movement. The Spring Fatigue Testing Machine is efficient without any pollution to the environment. Equipped with different accessories, the Spring Fatigue Testing Machine can test springs of different sizes. Adopting the single-chip machine control, the Spring Fatigue Testing Machine realizes auto stop function when it reaches the preset test times. The Spring Fatigue Testing System is widely used in quality controls for spring, shock absorber production, and relevant applications.
-
product
Electromagnetic Resonance High Frequency Fatigue Testing Machine
PLG Series
Jinan Testing Equipment IE Corporation
The series of electromagnetic resonance fatigue testing machines are used for fatigue tests of metal materials and components under tension, compression or reversal loads. If relevant grips are provided, three-point bending test, four-point and circle test, gear wheat, bolt, connecting rod, roller chain, crackle expanding test can be available. The series of electromagnetic resonance fatigue testing machines feature an optimized design and a rational structure. The automatic controlled system adopts an advanced and wide-pulse-control system and a new-type of power amplifier to improve the reliability of the electric system. The electromagnetic resonance fatigue testing system is with high efficiency, easy and non-stop shake, low energy consuming, accurate control, and small fluctuation.
-
product
Torsional Fatigue Testing Machines
T Series
These testing machines test the torsional strength characteristics of engines, turbines, and motors, and of shafts, couplings and clutches that transmit rotational torque used in automobiles, aircraft, carriages, electric motors, and machines.
-
product
Life Cycle & Fatigue Testers
Switches can use all these operations. Membrane switches, keyboards and keypads will all require a push with a known force. On/Off switches will combine a push and a pull or possibly push on, push off. A rocker switch and toggle switches will require a push in two different places. Rotary switches (and volume controls, potentiometers) need to be rotated clockwise and counter clockwise The standard life cycle and fatigue tester the B886 Simon System has been designed for life cycle and fatigue testing of switches, membrane switches, keyboards and keypads. It contains all the components needed to life and fatigue test a products that need to be pushed. We can also supply different actuators for a push, pull, rocker, toggle, volume control or rotary switch.
-
product
High Temperature XY Planar Biaxial Extensometer 1200 C or 1600 C)
Model 7651
Jinan Testing Equipment IE Corporation
Model 7651 extensometers measure combined in-plane strains in flat cruciform specimens tested in machines capable of simultaneous X and Y (perpendicular) axial loading and on standard flat samples tested in pure tension. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7651 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to eliminate crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃(2900°F) high temperature option.
-
product
Compact Hydraulic Vibrator Force Simulator
JF Series
The JF Series Force Simulator was developed with the emphasis on light weight, compact size and ease-of-use as a general-purpose, compact jack for the Servopulser system. Testing systems installed with the Force Simulator can easily perform endurance, fatigue and simulation tests on small structural members and various other structural members, which helps improve the logical design and reliability of products.
-
product
Seat Seam Fatigue Tester
TF152B
TESTEX Testing Equipment Systems Ltd.
Seat Seam Fatigue Tester is mainly used to test the seam fatigue (dynamic or static) of automobile interior materials such as fabric or leather, this fatigue test is determined by simulating the real vibration when driving.Colorful touch panel is equipped to set and control tests, and displays the test cycles, time. etc.
-
product
CO2 Monitor
T5000
Although carbon dioxide is invisible and odourless, increased CO2 content in the room leads to fatigue and decreased mental concentration.
-
product
DIgital 3D Image Correlation System
Q-400
The Digital 3D Image Correlation System Q-400 is an optical measuring device for true full-field, non-contact, three-dimensional measurement of shape, displacements and strains on components and structures made from almost any material.The Q-400 system is used for determination of three-dimensional material properties in tensile, torsion, bending or combined tests. In addition, deformation and strain analysis can be applied to fatigue tests, fracture mechanics, FEA validation, and much more.
-
product
Zipper Reciprocation Tester
UI-FT34
Zipper Reciprocation Tester is used to test zipper fatigue resistance under lateral and longitudinal tension.
-
product
Velcro Tape Fatigue Tester
UI-FT35
Velcro Tape Fatigue Tester is used to test the velcro tape/ hook and loop fastener to repeated closing fatigue resistance ability. Touch and close fastener repeated closing fatigue test is one of the necessary step for velcro strength test no matter for peel strength or shear.strength
-
product
Electromagnetic Force Micro Tester
Micro-Servo
This is a multi-functional fatigue testing machine suitable for specimens, structures and full-sized parts. It is an overhead actuator type with a broad test space, so it is ideal for various types of environmental tests, such as those in corrosion tanks or constant temperature tanks.
-
product
Pure Bending Fatigue Teesting System
PQ-6
Jinan Testing Equipment IE Corporation
PQ-6 Pure Bending Fatigue Testing Machine is suitable for testing the fatigue strength of metals and other materials under bending & rotating.
-
product
Optical Fiber Cable Testing Equipment
Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide. This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers then have a tough resin buffer layer and/or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications Optical fibers are very strong, but the strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging.
-
product
Flexural Damage Tester
DRK242A-II
Shandong Drick Instruments Co., Ltd.
It is used to test the dynamic anti-torsion and flexural fatigue performance of coated fabrics.
-
product
Cyclic Durability (Fatigue) Testing
Today’s products are very complex and designed to minimize costs with the use of FEA software that can project fatigue hot spots. Using your analysis results, we can create a test plan that includes mechanical cyclic durability and environments that will best test your design.
-
product
Instrumented Indentation Tester
With Anton Paar’s versatile indentation testers you can precisely determine the mechanical properties of thin films, coatings, or substrates such as hardness and elastic modulus. The instruments handle almost any type of material, whether soft, hard, brittle, or ductile. You can also conduct creep, fatigue, and stress-strain studies on surfaces in the nanometer range.
-
product
Electrical Creep and Rupture Testing Machine
ECR Series
Jinan Testing Equipment IE Corporation
This series of computer control electronic creep and rupture testing machine is newly designed with full-digital measuring control system to meet the standards of GB/T2039, GB//T20120, EN ISO 204-2009 and ASTM E139 etc. The electronic creep and rupture testing system can perform not simply creep. stress-rupture test and stress relaxation test on metals under room or high temperatures, but also low cycling test & creep fatigue test. The electronic creep and rupture testing machine is widely used for quality control in factories, material research in R&D department and teaching in universities,
-
product
High Force DMA
DMA 3200
The DMA 3200 combines decades of cutting-edge fatigue and world-leading Dynamic Mechanical Analysis technologies into a unique and highly versatile testing platform. The patented, frictionless Electroforce® motor technology, superior mechanical design, efficient environmental control, and wide variety of clamping systems deliver superior data accuracy for the broadest range of applications.
-
product
Electric Vertical Test Stand
WDW-L series
Jinan Testing Equipment IE Corporation
Electric Vertical Test Stand is a tensile compressive test stand especially designed to match push-pull force gauge. This series pf electric vertical test stand has good stability, wide application range and is convenient to use. The electric vertical test stand has stepless speed-adjusting uniform motion, digital display of the testing speed and converting mode between manual and automatic operation. The vertical test stand is specialized for tension/compression test, insertion/withdraw test, fatigue test and fracture test.
-
product
Standard Electromagnetic Vibrator
KD-9363-EM
King Design Industrial Co., Ltd.
The purpose of vibration testing is to make a series of controllable vibration simulation in lab, no matter generated by natural or man-made vibration environment; such as waves, tidal flaps, wind, earthquake or rain and so on. It is to test if the product is capable of sustaining the vibration environment exerted from transporting or usage along its effective life cycle; and certify the standard of design & functional requirement of product. The value of vibration testing is to confirm the reliability of products and effectively screen out the bad products in factory; avoiding damages occurred at arrival; and to assess the failure analysis on the non-performing products; expecting to reach a high standard, high-reliability products. The vibration test stresses on the continuity and fatigue; and contributes to the understanding of product’s status under vibration circumstance in a normal environment; and avoids the product’s unpredictable damage caused under certain vibrating frequency for a long time.
-
product
Fatigue Test Machine
JINAN PRCISION TESTING EQUIPMENT CO., LTD
Built to evaluate the strength of raw materials, components or finished products.
-
product
Load & Fatigue Testing
DATASYST Engineering & Testing Services, Inc.
Due to variations in types and levels of load and fatigue exposure, DATASYST works with each client to determine the best possible test plan to capture the information and issues that may be present in application.
-
product
Mechanical Tester
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
product
Folding Tester
FOT-01
Jinan Leading Instruments Co., Ltd.
FOT-01 Folding Testeris designed according to relevant standards and adopts modern mechanicalphilosophy and computer processing technology. Folding tester complies with relevant standard. It is suitable to test fatigue strength of paper, paperboardand other sheet material, which thickness is less than 1mm.
-
product
Handheld Thermal Cameras
Handheld thermal cameras are designed for a variety of industrial applications. They are ergonomically designed which minimizes fatigue when used for long periods of time. This series of products use high-performance Vox infrared detectors for extensive temperature measurement range and accurate measurement data, suitable for professional analysis work.
-
product
PHOTOMASK INSPECTION MACHINE
NEGATIVE FILM
Negative film and photomask inspection originated from the extensive use of printed circuit boards. Negative films and photomasks are used in large quantities. The early detection method is to use the "inspection light table" for inspection, which requires too much manpower and material resources, and manual testing may be due to eye fatigue and negligence.
-
product
Terahertz Spectroscopy Solutions
STRIPP Control IM
Teratonics offers innovative solutions for contactless non-destructive testing and imaging inside dielectric materials and on coated metallic surfaces. Based on the patented technology and our profound know how on its application, we offer: ► Instruments for product and process control as well as for inspection with automated evaluation ► Laboratory services for industrial R&D, fatigue tests, maintenance, end of life studies
-
product
Zipper Strength Tester
TF149
TESTEX Testing Equipment Systems Ltd.
Zipper Strength Tester, used for testing zipper strength or zipper fatigue test for puller attachment, closed-end, top stop, open-end fastener box, slider locking device.
