Distribution
transmission's network array.
-
Product
TTESync For VxWorks 653
-
TTESync is a synchronization component that allows tight synchronization of VxWorks 653 partitions to the fault-tolerant system-wide cycle time of the TTEthernet communication network. All partitions executed on different modules can be “pinned down” within the overall system cycle time, thus enabling the lowest latency and minimum jitter in message exchange among distributed functions. At system level this results in clean layering, well-understood functional interactions and simpler application design, testing and system integration. System architects can reduce system complexity and further optimize system size, weight, power (SWaP) and life-cycle costs.
-
Product
Predicting Microwave and RF Designs Virtually
RF Module
-
The RF Module is used by designers of RF and microwave devices to design antennas, waveguides, filters, circuits, cavities, and metamaterials. By quickly and accurately simulating electromagnetic wave propagation and resonant behavior, engineers are able to compute electromagnetic field distributions, transmission, reflection, impedance, Q-factors, S-parameters, and power dissipation. Simulation offers you the benefits of lower cost combined with the ability to evaluate and predict physical effects that are not directly measurable in experiments.
-
Product
Off-Line Base Test Platforms
-
To configure your Base Test Platform, the following parts can be added to the 6TL-19 bare half-rack:– Test Rack Manager, to control the test station.– Power Distribution Unit.– Uninterruptible Power Supply– Industrial PC or NI PXI to control the platform– 19’’ Monitor and keyboard with trackball– VPC Mass Interconnect Receiver (6 or 12 slots)– YAV Modules– Accessories: Beacon, Air inlet Pneumatic kit…– Any 19’ Instrument
-
Product
Virtex UltraScale+ HBM FPGA Processor - SOSA Aligned 3U VPX
Model 5586
-
- Jade 5585 and 5586 FAQ- Co-processor for distributed FPGA processing tasks- High-Bandwidth Memory (HBM) delivers 20x more memory bandwidth than traditional DDR4 solutions- Board interfaces: 1 GigE, 10 GigE, 40 GigE, dual 100 GigE and PCIe- High-bandwidth memory, FPGA logic and DSP density make this board a single-slot 3U VPX proessing powerhouse- Features Xilinx Virtex UltraScale+ HBM FPGAs- 10 GigE Interface and 40 GigE Interface- Optional VITA 67.3C optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA 46, VITA 48.11, VITA 67.3C and VITA 65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled- Navigation Design Suite for software and custom IP development
-
Product
High Voltage Probes To Measure Primary Waveforms With A Power Analyzer
Volt Litewire
-
The Litewire is a true RMS meter designed for use by electric utilities to sense currents or voltage waveforms from the primary side of their distribution networks.
-
Product
Particle Size Analyzers
NanoBrook Series
-
Brookhaven Instruments Corporation
Rapid and accurate protein & nanoparticle size distributionsMultimodal & unimodal size distribution softwareISO 13321 and ISO 22412 compliant resultsRange: < 0.3 nm to 10 mThree measurement angles: 15, 90, and 173Ideal for fast, routine sizing applications in research or quality controlHigh power 35 mW diode laserDynamic light scattering at 173 and 90Temperature control, -5 C to 110 CCompact bench top unit, USB connectionMolecular weight determination (relative and absolute through Debye plot)
-
Product
POWER INTERFACE BOX
-
The POWER Box is in charge to provide power supply lines towards the UUT simulating the power distribution unit. The box has been designed to host, in any mixed configuration, two kind of plug in modules:
-
Product
Ocean Surveyor
-
Teledyne Marine RD Instruments
For decades, Teledyne RD Instruments has been the preeminent supplier of Acoustic Doppler Current Profiling (ADCP) instrumentation for open ocean applications. Teledyne RDI’s vessel-mounted Ocean Surveyor family of ADCPs continues to raise the bar, collecting detailed maps of the distribution of water currents and suspended materials through the water column and along the ship’s path - at depths and resolutions previously considered unattainable. In real time, the ADCP is also used to aid in situ decision-making, to adapt field operations, and to understand current regime characteristics.
-
Product
Power Management & MMI Module
H73000700
Interface
This module, named “6TL-MMI”, is designed to be the interface between an operator and a SYSTEM as well as being a metered power distribution unit (PDU) for it. The module is providing also safety controls, data bus interfaces, temperature control and timers. The 6TL-MMI is suitable for any ATE, and specially for those based on CAN bus controlled devices, because in addition to the above functionalities, this module is also providing galvanic isolation up to 1500V for the CAN bus. This isolation will block potential disturbance towards the DUT.
-
Product
3U OpenVPX 2 Slot Profile BKP3-DIS02-15.2.8-3
1OVX302CZ3-1X11R
-
Distributed mesh, no expansion or control planes 3U, 2 Slot.
-
Product
L-Band RF Tuner and 2-Channel 400 MHz A/D with Kintex UltraScale FPGA - 3U VPX
Model 54891
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Two FPGA-based multiband DDCs (digital downconverters)- Xilinx® Kintex® UltraScale™ FPGA- Five GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Optional optical interface for data streaming- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Pulse Laser
-
Is a variable, pulsed high power laser source, a building block ideal for MOPA, LIDAR, OTDR laser systems development and applications. This fully integrated compact module contains a Distributed Feedback (DFB) laser and built-in optical amplifier stage, and a variable nanosecond pulse generation circuits. It provides up to 200 mW optical peak power in 1064 nm wavelength region, with a programmable pulse width from 10 ns to 1000 ns, and a selectable pulse repetition rate from 100 Hz to 1 MHz The optical pulse generation can alternatively be controlled via an external electrical trigger. In a compact design, NPL-CWDM-M is applicable for OEM integration or as a stand alone pulsed laser source. Contact Optilab for more information.
-
Product
6-Ch 200 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - 6U VPX
Model 58721
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three or six 200 MHz 16-bit A/Ds- Three or six multiband DDCs- One or two DUCs- Two or four 800 MHz 16-bit D/As- Multiboard programmable beamformer- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
DC Power Systems
-
Allow efficient distribution of your telecom and data center power utilizing these reliable, scalable and flexible DC power products.
-
Product
Water Distribution Monitor
TW-100
-
HORIBA’s TW-100 is a process water quality measurement system designed for drinking water and water distribution plants. The TW-100 monitors turbidity, color, free chlorine and pressure. This chemical free method reduces operating costs as it requires minimal maintenance and improves process control.
-
Product
Standards
7X
-
WENS series Frequency / Voltage / Wave / Carrier Standards is an ideal and smart solution for distributing signals from Quartz or GPS receivers. Designed to multiple output for multiple applications.
-
Product
Disciplined OCXOS
-
GPS Disciplined OCXOs (Oven Controlled Crystal Oscillators) are a range of advanced clock modules which provide electrical timing functionality for distributed network systems. These units primarily revolve around the 1PPS (pulse per second) timing synchronisation signal produced by a GPS frequency receiver which is derived from transmitted timing information received from GPS satellite systems.
-
Product
FPGA Mezzanine Card
FMC407
-
The FMC407 is a low noise clock generation and distribution module with eight clock outputs and eight trigger outputs that are fully synchronized.There are two configurations: 34.375MHz-200MHz or 34.375MHz-4.4GHz. The FMC407 is ideal for applications that require synchronous A/D or D/A sampling across multiple cards or systems.
-
Product
Centralized Management of Distributed Voice & Radio Systems
CERTIUM MANAGEMENT
-
Easy-to-use centralized management of VCS and radios provides a real-time view of the system and enables central system configuration and software management.Using multiple configurations, the system can be easily switched over to new parameters but also rolled back if needed. Central monitoring and reporting make the work of the system administrators much more efficient.In the CERTIUM® portfolio there are two management systems available, R&S®RCMS II and R&S®VCMS. The R&S®RCMS II allows monitoring of the entire ecosystem and provides the entire radio management and configuration. the R&S®VCMS provides the monitoring of the entire ecosystem and integrated the management of the CERTIUM® VCS and GATEWAYS components.
-
Product
2-Channel 200 MHz A/D with 766 DDCs, Kintex UltraScale FPGA - XMC
Model 71865
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete software radio receiver solution for extremely high-channel-count applications- Uses Xilinx Kintex UltraScale KU035 FPGAs- Two 200 MHz 16-bit A/Ds- Four wideband DDCs (digital downconverters)- Up to 762 narrowband DDCs- Sample clock generation and synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Imaging Luminance Meter
CX1000
-
Hangzhou Hopoo Optoelectronics Technology Co., Ltd
CX-1000 imaging brightness meter is used to measure the brightness, brightness distribution and uniformity of LED modules, lamps, lamps, displays, street brightness and other light sources.
-
Product
8-Channel 200 MHz A/D with 64-Channel DDC, Virtex-6 FPGA - 6U VPX
Model 58662
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Eight 200 MHz 16-bit A/Ds- 64 channels of multiband DDCs (digital downconverters)- Up to 4 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Remote Intelligent Pod
ScanTAP
-
The test patterns generated by the PCI-1149.1/Turbo controller are distributed to the target system either directly through ScanTAP 4 and ScanTAP-8 pods. The ScanTAP-4 and ScanTAP-8 pods can apply test vectors and/or ISP patterns to target boards with a variety of JTAG chain topologies. In the simplest case, the ScanTAP-4 and ScanTAP-8 will provide the interface between the PCI-1149.1/Turbo controller and a target system consisting of a single JTAG Test Access Port (TAP). This would be the case where the target system consists of one JTAG chain and its single associated TAP.
-
Product
Data Record Adaptor and Correlator
Joiner
-
nTh Network Technologies to Help
Joiner is a data record adaptor and correlator for mobile and core networks management. The ideal partner for big data architectures with data lakes and analytic applications. Distributed as Docker component, it may be orchestrated in line with the network virtualization function concepts.
-
Product
4-Channel 200 MHz A/D with DDC, Kintex UltraScale FPGA - 6U VPX
Model 57861
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
MultiStandard Advanced Monitoring Probe
EdgeProbe Advanced MultiStandard
-
The ideal tool for accurate & cost-effective monitoring probe for:DTV terrestrial transmission (DVB-T/T2, ISDB-T/Tb)DTV cable transmission (DVB-C/C2)DTV distribution over satellite (DVB-S/S2, T2-MI, OneBeam, MPTS)DTH uplink and reception (DVB-S/S2, MPTS)Digital Radio transmission (DAB/DAB+/T-DMB)Combine any two RF standards in one single 1RU device.Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing Digital TV & Radio network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor the RF signal, through its RF inputs (up to 4 in 1RU), as well as the baseband transport before modulator, through its ASI and IP inputs.
-
Product
WinstonCones
-
Our Winston Cone condenser is a field optic designed for maximum concentration of far infrared and sub millimeter radiation. Its principal functions are to:*Concentrate the radiation onto a detector smaller than the field aperture*Restrict the field of view of the detector*Distribute the incoming energy uniformly across the detector
-
Product
NI-5791, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782510-01
RF Adapter Module
The NI‑5791 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5791 modules. For higher frequencies or a greater number of devices, you can use an external LO distribution amplifier.
-
Product
LED626/620 Goniophotometer For LEDs
-
Hangzhou Everfine Photo-E-Info Co., LTD
It can measure the luminous intensity data and automatically plot the luminous intensity distribution curve and luminous flux, and the test conditions meet the CIE condition A (far field) or condition B (near field).In addition, the software can provide customers with 3D luminous intensity distribution graphic.
-
Product
DOUBLE FREQUENCY DOUBLE VOLTAGE TEST SET
-
International Biological Laboratories
This test set provides a continuously variable output voltage at double frequency to test the insulation between turns of coils, layer to layer, terminals of windings with either uniform or graded insulation and also between the windings and earth, with graded insulation of both Distribution and Power transformers.
