Wiring
See Also: Wiring Analyzers, Trailer Harness Testers, Harness
-
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, .025" Round Post
610138115
Primary mating contact 610138200. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body (RCV) – BeCu (Twin Female)BeCu/PhBrz (Crimp)Male (ITA) – BrassContact Plating Female (RCV) – 50µ” Au over 100µ” NiMale (ITA) – 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
8-Pin Power D-Type Cable, Female to Unterminated, Ferrules, 1m
A008PF4-F-5A100
The 8-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
product
Circbord
8019-1
VECTOR Electronics and Technology, Inc.
Single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges. 3U X 160mm Eurocard size will fit into 3U DIN Metric subrack.
-
product
Socket Tester c/w Buzzer
DL1090
Clear visual and audible indication of wiring status LED indication of a wide range of wiring conditions Designed to EN 61010 and IP30
-
product
Cable Assembly, 50-Pin D-Type, Male to Female, 1m, Exit Away From Pin 1
40-970-050-1m-MF
The 50-Pin Cable Assembly is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
8-Pin Power D-Type Cable, Male to Male, 0.5m
40-970-408-0.5m-MM
The 8-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Tinned Ends, 2m, HV
A009DF4-T-HA200
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
product
CMP
CMPs remove unevenness on wafer surfaces that occur during the production process. Applications are growing due to the increase of layers in semiconductor devices and the growing variety of wiring materials.
-
product
48-Channel High Performance Strain Gauge Measurement Instrument
EX1629
48-Channel High Performance Strain Gauge Measurement InstrumentSupports quarter-bridge (120, 350Ω or user defined), half-bridge or full-bridge24-bit ADCs, sampling rates up to 25 kSa/sBuilt in programmable differential excitation -8V to 8VBuilt in selectable bridge completionConfigure signal conditioning excitation and bridge completion on a per channel basisSimple, low-cost wiring using RJ-45 telecom connectorsSupports TEDS for easy transducer detection and setupRJ-45 input connector reduces setup cost and timeBuilt in self-calibration and shunt calibrationSupports voltage, ratiometric and linear measurements other than strain measurements.
-
product
Rope Tension Meter
RTM
The PIAB RTM Rope Tension Meter is very simple and handy to use. Simply hold and “clip” it to the rope to be tested and use the large hand screw to deflect the rope to a fixed angle. The resultant force will affect the load cell and measure the tension in the wire rope. The resultant signal is digitally processed and displayed in a selected pre programmed graduation. The PIAB RTM 20D can be graduated in kN, klbs or in ton.
-
product
Lever Handle Bed of Nails Testers
Automator Manual Family
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
product
Multifunction Installation Tester
ProInstall-75-UK
The Beha-Amprobe ProInstall-75-UK, with new advanced features, is the perfect installation testing tool for verifying the safety of electrical installations in domestic, commercial, and industrial applications. Ensure that fixed wiring is correctly installed and compliant with IEC 60364, HD 384 requirements and BS7671 17th Edition wiring regulation meeting local requirements. The ProInstall-75-UK is efficient to use by allowing the user to measure loop impedance without tripping RCDs, eliminating the need to bypass them.
-
product
Osprey Probe Card
The Osprey probe card is MPI’s solution to demand for ever finer pitch. It is designed for smaller Al pad, and is ideal for tiny pitch application with peripheral and full array pattern. With precise alignment and better planarity control, Osprey can reach higher productivity by multi-DUT design. The forming wire (FW) type needle produced with MPI’s own micro fabrication process not only delivers high-quality performance but also allows easy needle replacement and shortens maintaining cycle time.
-
product
TV Signal Generator
This device is equips with the simulator. The following condition can be simulated. Non Liner: Non-linear assumed the satellite repeater - AWGN: C/N assumed the rain attenuation.- Phase Noise: Phase noise assumed the LNB - Frequency Drift: Frequency drift assumed the LNB- Echo: Reflection by the reception wiring and so on The MPEG-2 TS and the TLV (Type Length Value) can be transmitted. The test stream generator is equipped. Thus, the files can be rewritten through the USB2.0 interface. A seven-inches WVGA touch-panel is equipped. Thus, an excellent operation ability is provided. The remote control through the Ethernet is possible.
-
product
PCIe-8431, PCI Express, 2-Port, RS485/RS422 Serial Interface Device
782124-01
The PCIe‑8431/2 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between … 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
Smart MUTT Updated Trailer Tester
#9007A
Innovative Products of America
The Smart MUTT is a portable trailer tester for the mobile and commercial trailer repair technician. It places a load on the trailer's electrical circuits to identify wiring problems while providing remote control operation for the lights. The Smart MUTT is powered by an (optional) internal 12v battery and provides an easy method to accessing trailer ABS blink codes.
-
product
1' Harness, 50-Pin Male D-Sub Connector on one end, loose wired (numbered) other end
GT97106
1' harness, 50-pin male D-sub connector on one end, loose wired (numbered) other end.
-
product
MS-M 3-Pin RF Cable Assembly, Female to Unterminated, 0.5m, RG178 Cable
40-979A-503-0.5m-FU
This 0.5m long MS-M RF 3-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with FEP insulation and an attenuation of 102dB/100m at 500MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
-
product
Advanced Diagnostic Load Cell Tester
LCT-U
The Advanced Diagnostic Load Cell Tester Model LCT-U is a stand-alone hand-held device specially designed for fast, comprehensive troubleshooting of strain gauge load cells. The LCT-U can quickly diagnose problems with all common types of load cell available today, including 6-wire load cells (with sense wires).
-
product
Cable, 10 Pos Combicon to Pigtail, 2 Meters
190656-02
The SH10M-10F Cable, sometimes referred to as SH10F-P, connects C Series DAQ devices with a 10-pin screw terminal to open signal wires. The SH10M-10F Cable is offered in different lengths.
-
product
Split type AC Current Sensor
CTF-200A
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of feeder. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
-
product
High Voltage (Hipot) Cable Tester
CH2
The easy-wire CH2 was designed for commercial, military, and aerospace applications. Running on powerful Windows-based software, the CH2 offers unrivaled testing capabilities at an unparalleled price. Compact, easy-to-use, and FAST (shorts/mis-wires detected in <1 sec for 20,000 points), the CH2 is positioned to become the ''''tester of choice'''' for high-end users.
-
product
Pull-Thru Adapter, Wired, TriPaddle, 68 Pin ML VHDCI, f/ AIT PXI-C1553
510140197
Pull-Thru Adapter, Wired, TriPaddle, 68 Pin ML VHDCI, f/ AIT PXI-C1553.
-
product
PXIe-4357 , 20-Channel, 24-Bit PXI Temperature Input Module
782118-01
20-Channel, 24-Bit PXI Temperature Input Module—The NI PXIe‑4357 input module provides integrated data acquisition and signal conditioning for 2‑, 3‑, or 4‑wire resistance temperature detector (RTD) measurements. It offers both high-speed and high-resolution modes. It provides per channel software-programmable configurations and automatically scale measured data into engineering units.
-
product
2 Pole 12 X 4 Low Thermal Relay Matrix Module
DP-cPCI-4113
A matrix is the most versatile switch topology. It is made up of rows and columns that connect any input to any output. With matrix switching system, it is easy to connect a number of instruments or sources to various test points of the UUT. The benefit of matrix switching is simplified wiring with which the overall test system can easily and dramatically change the internal connection paths without any manual intervention.DP-cPCI-4113 offers switching matrix in a single slot 6U sized cPCI module with flexibility to configure for 48 cross-points or 72 cross-points on factory selectable basis.
-
product
LanCaster
4402700
Indicates all common wiring faults including split pairs Shows which end the installed link contains the fault Cable Length Meter, Tone Generator & Service Indicator Instant digital display gives unambiguous fault indication Rugged Palm-Top design weighs less than 350g (12oz) Complete with 1 Active Remote unit and test leads Up to 16 unique Active Remote units / Office Identifiers
-
product
Fixed Gas Detectors
DG7 Series
Teledyne Gas & Flame Detection
All DGi-TT7 are constructed from a common housing and electronics with the detection properties being determined by the type of sensor (cartridge) used. A wide range of cells are available, these cells are intrisically safe protected, and may be replaced with the detector powered which minimises the system down time. The intelligent, microprocessor driven unit is fully configurable using a wireless hand-held terminal (TLU) or by using the hard wired HART option giving true flexibility to the installer and reduced service costs.Elements such as relay operation and alarm levels are all set via the TLU, a hazardous area approved hand-held unit. The unit may be interfaced directly with a wide range of panels, controllers and PLC’s etc. Its integral daylight readable alphanumeric display indicates local status and alarm level.
-
product
Automatic Battery Testers
T100BT is an innovative, modular battery testing equipment able to combine, on a single test platform, all the tests required to detect any possible defect on battery cells and modules: from defective cell wiring, to geometrical or surface irregularities, to out-of-specs performances.The battery tester is designed for the high-volume production test of battery modules composed by prismatic, cylindrical, or pouch cells, as well in a Lab/NPI version for engineering, prototypes and low-volume battery testing. The complete configurability allows you to equip the tester with the modules and tools you need to test your products, reaching the desired throughput.
-
product
Cable Assy 9-Pin D-Type, F/F, 1m
40-970-009-1m-FF
The 9-Pin Female connector option of this cable assembly is suited for direct connection to corresponding Pickering Interfaces products, and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
product
CHEK 3-in-1 Electrical Tester
GT 3100GAM
Cable test monitors line continuity, shows completed circuits. Lamp test indicates the lamp and fixture continuity. Circuit tester checks if power is available, if polarity is correct, if wiring is correct.
