Wiring
See Also: Wiring Analyzers, Trailer Harness Testers, Harness
-
product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends, 2m, Screwlocks
A068SFR-T-6B200
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
Load Cell Power Supply Module
MODEL PSM-F10
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
product
9050 Slide Mount
The 9050 Slide Configuration provides maximum test system versatility. This configuration allows for easy instrument wiring and chassis access which allows for shorter cable lengths and a flush rack mount to save valuable work space.Ordering has been simplified with packages offered that include the 9050 receiver, receiver mounting plate, flanges and instrument bracket. Slide kits are available in depths designed to fit most common racks. To determine the slide kit needed, measure rack depth between mounting rails. Slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures.
-
product
SoftLine
When connecting two Network Interfaces together over a network or over the Internet, a virtual four wire audio line is created. Along with the audio line you get an RS232 connection and some I/O-ports.
-
product
Signal/Micro Power/Micro Coax, Module, Receiver, TriPaddle, 90 Series, 20/20 Position
510104323
Signal/Micro Power/Micro Coax, Module, Receiver, TriPaddle, 90 Series, 20/20 Position.This hybrid module provides 20 TriPaddle Signal positions and 20 Micro Power or Micro Coax positions in a single wide module slot enabling consolidation of wiring and preserving valuable space in the Receiver.*Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
product
PCI RTD Simulator Card 6-Channel PT100
50-262-101
This RTD Simulator is a PCI card that supports 6 channels of RTD simulation. The card provides a setting resolution of <8mΩ (also available in <90mΩ - PT1000version) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
product
Continuity of Insulation Tester (High Voltage Method)
ZGQ-16B
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-5;Inspection standard: JB/T4279.13-2008Meet GB/T6109-2008 standard requirementsUsed to test the Insulation continuity (namely the pinhole number of enameled wire sample per unit length) of enameled round wires with nominal conductor diameter ranging from0.05mmto1.60mm;8 level test voltages can be selected by pressing button: 350V, 500V, 750V, 1000V, 1500V, 2000V, 2500V and 3000V;Test length ranging 0～99m;Application of SCM control.Automatically complete test process, display wire testing length and pinhole number;Brushless driving motor, guide pulley and take up pulley are equipotent.The electrode insulation to ground, using high resistance material of non-hygroscopic, no leakage, no tracking, easy to clean, Insulation thickness can ensure long-term 3000V voltage effect.Circuit board is subject to anti-static and moistureproof and long-time aging treatment, has more stable quality and higher durability;
-
product
Cable 96-Pin Micro-D Female to Unterminated, Ferrules, 1m
A096SFR-F-5A100
The 96-Pin SCSI Style Micro-D to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
product
Contactors
Mitsubishi Electric Automation, Inc
Compact dimensions, modular expansion options and a power-saving design are the key characteristics of the MS-N and MS-T series magnetic contactors. DIN rail mountable and standardized terminal covers make installation and wiring user friendly and cost effective.
-
product
Cable Length Meter
UEi Test & Measurement Instruments
An excellent tool to measure spooled cable/ wire.
-
product
4-Pin Power D-Type Female to Unterminated With Tinned Ends
A008PF4-T-6A100
The 4-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
product
Switch Probes
A switch probe is designed primarily for “presence/ electrical” test applications such as detecting the absence or presence of contacts within a wire harness connector. In this case, the switch probe provides electrical interconnection and verifies the connector has been manufactured properly. If contacts are missing or out of place, the part is rejected. If all the contacts are in place, the part is accepted and an electrical test is performed, verifying the electrical integrity of the connector and the wires within the harness.
-
product
High density, ESA approved PCB connector
KMC Series
Smiths Interconnect's KMC series is an ESA qualified, high density board to board and board to wire interconnect available in multiple configurations from 26 to 162 positions
-
product
Plugbord
4112-5
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.156"(3.96mm) centers.3-hole solder pads (0.28” x 0.080”) for interconnecting multiple components. Zig-Zag Bus Pattern on wiring side. Zig-Zag Bus Pattern provides access to voltage or ground at alternating hole positions.Continuous ground plane on component side with 0.085” etched clearance area around each hole. Row and column legends provided.
-
product
LED Driver Automatic Test System
ATE-2
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection. •It can test 4 LED drivers input and output at one time. •The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer. •Enable to print out the series number and parameters of sub-quality products by working with a micro-printer, •Enable to achieve the bar-code record function by working with a bar-code scanner. •The test report can be saved as Excel file for consult, statistic and analysis purpose. •Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
-
product
Utility Locator
VM-810
Using the correct frequency makes a world of difference when locating buried utilities. The depth of the utility, size, material, and amount of congestion (proximity of other utilities) all need to be taken into consideration for the correct frequency selection. Large diameter, direct buried pipes with bell housing ends that use insulators and rubber gaskets, such as water or gas require a higher frequency while smaller diameter, well-grounded direct buried or long distance in conduits work, better with a lower frequency. The VM-810 operates at 83.1kHz which is ideal for water and gas utilities which generally are larger pipes with bell housings and gaskets. The VM-810’s higher frequency is also good for locating ungrounded small diameter drop wires and inducing signals through the soil, onto services when direct connecting is not an option.
-
product
Rear Cover, S6, Tabletop Configuration, For Part # 310 122 100
310113431
The Rear Covers are designed to enclose the wiring that runs from the S6 Receiver on the tabletop to the instrument cards below. This rear cover is used with the S6 Receiver Part # 310 122 100.
-
product
Wire Crimp Pull Tester (Manual)
WT3-201
The WT3-201 wire crimp pull tester is designed to measure the pull-off force of crimped wire and tube terminations. An ergonomic lever allows for easy application of up to 200 lbF (1,000 N) of crimp pull force. Adjustable wire terminal grip contains multiple slots for wire diameters up to AWG 3 (0.25 in [6.3 mm]). The tester accommodates most insulation types. Samples can be sent to Mark-10 for evaluation prior to purchase.
-
product
Super MUTT Deluxe Edition Electrical Circuit Tester
#9008-DL
Innovative Products of America
The Super MUTT places a load on the trailer's electrical circuits to identify wiring problems while providing remote control operation over both air brakes and lights. Built to facilitate a one-man testing operation, the Super MUTT reduces guesswork and inspection time to prevent failures that lead to expensive road calls and citations. The remote control allows for repetitive air brake actuation at each axle to reveal developing problems often missed by normal testing procedures.
-
product
6 Ft Harness, 78 Pin Male Connector On One End, Loose Wires (numbered) On Other End
GX96105
6 ft harness, 78 pin male connector on one end, loose wires (numbered) on other end.
-
product
Eurocard Plugbord
E160-3U-2
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Voltage and ground buses around board perimeter on both sides. Bus surfaces solder coated for user convenience.For solder, Wire-Wrap or mixed wiring methods. Row and column legends provided.
-
product
Belt Tension Tester
BTT2880
Main used in belt tension measurement, can also be applied to measure the tension of objects such as tapes, wires. Widely applied in industries of automobile, textile, cables, wires, plastic films, paper, printing.
-
product
Interior Temperature, Humidity Transmitter
T3318
For exacting interiors in building energy management and HVAC systems. Are designed for easy installation on ordinary KU68 wiring boxes for household switches and sockets.
-
product
Plugbord
4112
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.156"(3.96mm) centers. 3-hole solder pads (0.28” x 0.080”) for interconnecting multiple component leads. Zig-Zag Bus Pattern on wiring side. Zig-Zag Bus Pattern provides access to voltage or ground at alternating hole positions. Continuous ground plane on component side with 0.085” etched clearance area around each hole Row and column legends provided
-
product
Chassis - Control Relays Greater than 8x1 or Control Multiple Relays in Series Forming Larger Switches than Normally Possible Such as 16x1 to 32x1 Sections.
CXM/256-MF
These Chassis are typically used to control relays greater than 8x1 or control multiple relays in series forming larger switches than normally possible such as 16x1 to 32x1 sections. Or control mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 256 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
product
Wire Trackers
This product is a multi-functional handheld cable testing tool. It has wide application with reinforced cable types and multiple functions, which is a necessary testing tool for telecommunication engineering, wiring engineering and network maintenance personnel
-
-
product
Scanning Vibrating Electrode Technique
VS-SVET
The Scanning Vibrating Electrode Technique uses a single wire to measures voltage drop in solution. This voltage drop is a result of local current at the surface of a sample. Measuring this voltage in solution images the current at the sample surface. Current can be naturally occurring from a corrosion or biological process, or the current can be externally controlled using a galvanostat.
-
product
Pneumatic Flat Grips
For tensile testing rubbers, plastics, elastomers, textiles, cloth, and paper, in specimen geometries such as plates, films, and wires, a good option is pneumatic flat grips. Quick clamping and a repeatable clamping force are advantages of pneumatic flat grips.
-
product
Cables Testing Equipment
Quality control in the cable and wire production industry requires high voltage testing of the insulating coating just after it has been applied.
