Counting
-
Product
PXI Very High Density Multiplexer, 2A, 79-Channel, 2-Pole, Single Channel Mode
40-611B-002
Multiplexer Module
The 40-611B-002 (PXI) and 42-611B-002 (PXIe) modules are 79-Channel 2-Pole multiplexers. A 158-Channel 1-Pole configuration is also available. They use high quality electro-mechanical signal relays allowing switching up to 2 A and voltage up to 300 VDC/240 VAC.They are suitable for signal routing in high channel count ATE and data acquisition systems. Connections are made via a front panel 160-pin DIN 41612 connector.
-
Product
Automated Filter Tester
3140-1
-
The model 3140 filter tester uses the same aerosol generation technology as the model 8130A respiratory filter tester. It works with Emery oil, DOP, DEHS, paraffin and other oils. Two new generation CPCs simultaneously count upstream and downstream particles. This enables accurate, repeatable and fast measurements, for example a HEPA filter can be tested in less than 15 seconds.
-
Product
FREQUENCY DISPLAY UNIT
TYPE NFD-1
-
The National RF Type NFD-1 Frequency Display Unit was designed for use with vintage and classic communications equipment, to display the received or transmitted radio frequency. The unit incorporates an internal processor that allows the intermediate frequency (IF) to be counted out by the frequency counter. The resultant display is the actual frequency that the equipment is receiving or operating at.
-
Product
95 Ohm Coax Cable
RG180B/U
-
RG180B/U part number from Pasternack is a RG180 coax cable that is flexible. Pasternack RG180 flexible coax cable is 95 Ohm and has a PTFE dielectric. Our RG180 coax is constructed with a 0.141 jacket made of FEP. RG180 coax has a shield count of 1 and the maximum frequency for this Pasternack cable is 3 GHz. RG180 coax cable has a maximum power of 250 watts at 1 GHz.
-
Product
PXI BRIC4 FIBO Matrix Dual 31x4 2pin brkout
40-592A-011
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Microscope Cameras From ZEISS
Axiocam Family
-
In contrast to digital cameras for photography or industrial inspection, many aspects of the microscope cameras are optimized to meet specific requirements of applications in science, research and documentation. As each application has very specific requirements, there is a wide range of different digital camera models to choose from. Different pixel sizes, for example, regulate camera sensitivity and spatial resolution. Lower pixel count enables higher frame rates and larger sensors offer better coverage of the field of view.
-
-
Product
PXI High Density MUX BRIC, 64-Chan, 10-Pole
40-570-414
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
NI-9326, 6-Channel, 150 V, 128 kHz C Series Frequency Input Module
786999-02
Frequency Input Module
6-Channel, 150 V, 128 kHz C Series Frequency Input Module - The NI-9326 is a channel-to-channel isolated frequency input module for CompactDAQ and CompactRIO systems. This module includes six differential input channels with a 0 Vrms to 150 Vrms input range. The NI-9326 also features configurable thresholds for connection to a variety of variable reluctance sensors, single channel encoders, and hall-effect sensors. You can use the included embedded counters to perform frequency measurements or edge-counting for tracking total counts on a periodic signal. Additionally, the NI-9326 supports configurable Butterworth filters to help you perform low-noise frequency measurements.
-
Product
Palm Size Digital Multimeter, Calibrated, 1999 Count, Mean Value, Manual Range, 3.5 Digit
72-7770 CAL
-
The 72-7770 CAL from Tenma is a palm sized digital multimeter with 3 3/4 digit LCD. It is 3 1/2digits with steady operations, fashionable design and highly reliable hand held measuring instrument. The meter measures AC/DC voltage, AC/DC current, resistance, temperature, diode and continuity. It is an ideal tool for maintenance. The multimeter features square wave output, data hold, low battery indicator and display backlight, This meter complies with the standards CE, IEC61010, in pollution degree 2, overvoltage category (CAT I 600V, CAT II 300V) and double insulation.
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-01
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
COM Express Type 10
-
The COM Express Type 10 Mini (84 x 55 mm, credit card size) module is intended for low power platforms (TDP 12W and below), capable of entry level processing with ultra-low power consumption, while supporting graphics and optimized I/O count for mobile applications. Type 10 modules are targeted at handheld devices (smart battery) for industrial, medical, transportation, and controllers for outdoor applications.
-
Product
PXI 3A Power MUX BRIC, 9-Channel, 16-Pole
40-571-203
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Sensors
-
As traffic management challenges intensify, ITS strategies prioritize the multitasking capabilities of intelligent detection sensors. Econolite’s sensors exceed basic traffic detection by performing tasks like counting, classifying, tracking, and providing advanced detection for adaptive systems and dilemma zone safety. In modern multimodal intersections and roadways, advanced detection sensors are indispensable, featuring capabilities for bicycle and pedestrian detection and differentiation.
-
Product
PXI BRIC4 FIBO Matrix Dual 60x4 3pin brkout
40-592A-003
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Dual Display Auto-Ranging LCR Meter
LCR 459
-
Kusam Electrical Industries Limited
• Dual Displays provide quick tested results readouts, with L.C.R. display values up to 19999 counts and Q.D.R. display values up to 9999 counts • Test 4 parameters : Ls+(Q,D,Rs), Lp+(Q,D,Rp), • Cs+(Q,D,Rs), Cp+(Q,D,Rp) • RS-232 PC Interface • External DC Adapter functions • Set Hi / Lo limits using absolute values or percentage limits.
-
Product
PXI-2533 , 256-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-33
Matrix Switch Module
256-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2533 is a high-density 4x64 PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring solid-state relays (SSRs), the PXI‑2533 offers unlimited mechanical lifetime and the ability to route 55 W simultaneously on all channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
PXI/PXIe High Voltage Multiplexer, Dual 4-Channel, 2-Pole
42-321-120-HI
Multiplexer Module
The 40-321-120-HI (PXI) and 42-321-120-HI (PXIe) are dual 4-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
sbRIO-9213, Non-Enclosed, 16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module
781210-01
Temperature Input Module
Non-Enclosed, 16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module - The sbRIO-9213 is a high-density thermocouple input module that is designed for higher-channel-count systems. With this module, you can add thermocouples to mixed-signal test systems without taking up too many slots. The sbRIO-9213 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The sbRIO-9213 features NIST-traceable calibration and a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. Non-enclosed modules are designed for OEM applications.
-
Product
General Purpose Manual Ranging 1000V Multimeter
DL9101
-
Double moulded housing with an oversized high contrast 2000 count LCDdisplay. Manual ranging with current range up to 20A, temperature and frequency test.
-
Product
Bench Power Supply
E3630 Series
-
When your requirements demand more power, the E3630 Series power supply offers up to 200 W per output. This linear power supply meets the requirements of the most demanding applications in R&D design verification, production testing, and quality assurance (QA) verification with reliability you can count on.
-
Product
ScanBridge
JT 2154
-
The JT 2154 is an experiment board based on National Semiconductor’s STA111 device, aimed at users looking to utilise addressable bridge/multiplexors within their designs, and thus set-up ‘system level’ JTAG access. The unit can also be used in semi-permanent installations to expand the TAP (Test Access Port) count on JTAG Technologies controllers in order to address highly segmented designs. Built-in support for ScanBridge-type devices within ProVision allows easy set-up of TAP assignments and device addressing.
-
Product
Torque Screwdrivers
-
From better product quality to a lower total cost of ownership to guaranteed regulatory compliance, you can have it all with market leading Mountz torque screwdrivers. Built-in cam-over mechanisms prevent over and under-torque conditions so you can count on the quality of your work. Assembly and repairs performed with Mountz torque screwdrivers allows any user to deliver precision torque control with confidence regardless of task and operator skill level. And when it's time for compliance inspections or audits, equipment calibration records provide clear documentation. In short, Mountz torque screwdrivers keep your operation tight.
-
Product
VME 32X 5 Slot 6U
-
ANSI/VITAV 1-1994 VME32 Backplane, 6U 5 Slot Including J1 & J2.Benefits:• Standard VME backplanes are available also in other slot count configurations• Surface Mount Technology – Excellent high frequency performance, high reliability and reduced cost due to SMT
-
Product
LabMaster Modular Oscilloscopes
LabMaster 10 Zi-A Series
-
The LabMaster 10 Zi is the world's highest bandwidth real-time oscilloscope - 100 GHz at 240 GS/s. LabMaster 10 Zi-A is also modular - it breaks channel count barriers and provides more "bandwidth density". The modular design provides the simplest upgrade path in bandwidth and channel count, with one acquisition module providing four channels at 36 GHz or two channels at 65 GHz, with capability for up to 20 acquisition modules
-
Product
PXI High Density MUX BRIC, 80-Chan, 10-Pole
40-570-415
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Radioactivity
-
Higher than the natural ambient/background radiation, it originates from building materials or is inhomogeneous at geological faults and underground watercourses. It causes cell damage (tumors), cell death, etc. Radioactivity (=ionizing radiation) is measured in sieverts per hour (Sv/h) or simply as a count rate (pulses/second [Ips] or pulses/minute [Ipm]).
-
Product
Ground Resistance Testers
-
Whether you are doing a simplified 2-Point, a more complete 3- or 4-Point Fall-of-Potential test, a soil resistivity test or a touch potential test, AEMC has the right instrument for you. Our revolutionary clamp-on ground resistance tester will save you both time and money. Whichever AEMC ground tester you choose, you can count on it to be the highest quality, the most complete package and the simplest to learn to use.
-
Product
Geofob™ Mobile Panic Button
-
The Geofob™ connects with our Know When It Counts® application. It integrates with our existing network of smart sensors and uses a patented industry-leading localization method.
-
Product
PXIe-4141, 4-Channel, ±10 V, 100 mA, Precision PXI Source Measure Unit
781743-01
Source Measure Unit
PXIe, 4-Channel, ±10 V, 100 mA, Precision PXI Source Measure Unit - The PXIe-4141 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4 wire) sensing for accurate measurements. The fast sample rate of the PXIe-4141 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4141 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
