V.35
-
Product
Bench Power Supply, Single, Adjustable, Fixed, 3 Output, 0 V, 30 V, 0 A, 10 A
72-7660
-
Compact, regulated constant voltage power supply for service field, hobby and telecommunication equipment. It provides three different voltage output for different usage.
-
Product
Electric Safety
PV-ISOTEST
-
PV-ISOTEST represents a real innovation in the panorama of PV verification and testing instrumentation. PV-ISOTEST measures the insulation resistance of a single module, a string or even an entire photovoltaic field up to 1,500 V DC according to IEC/EN62446 standard.
-
Product
Seismometers
3T-120 Pothole
-
120 s to 50 Hz frequency response (option to 100 Hz), 1500 V/ms-1 (2 x 750 V/ms-1) sensitivity, Covers the complete seismic spectrum with a single transfer function, Measured Self noise below the USGS NLNM from 166 s (0.006 Hz), remaining below the high frequency limit of the NLNM at 10 Hz, High linearity: >111 dB (USGS figures), Dynamic range of 167 dB at 1 Hz (Full octave width across 1 Hz), Cross axis rejection over 65 dB; sensor axes orthogonal to within ±0.05°, Remote, automatic electronic mass locking, unlocking and centring, Operating tilt range of ±5° with adjustable feet for off-horizontal installation bases, Low power consumption: 0.75 W from a 10–36 V supply, Stainless steel enclosure, 100 bar / 10 MPa waterproof connector, IP68 - protection against effects of permanent immersion under pressure to 350 m depth
-
Product
100W Dual Output Power Supply Two 35V, 1.4A or 60V, 0.8A
E3649A
Power Supply
Output ratings (@ 0C to 40C) 2 outputs Range 1: 0 to 35 V / 1.4 ARange 2: 60 V / 0.8 A Programming accuracy (@ 25C 5C), (% output + offset)Voltage: <0.05% + 10 mV (<0.1% + 25 mV for output 2 of E3646/47/48/49A)Current: <0.2% + 10 mARipple & noise 20 Hz to 20 MHz Normal Mode Voltage: <8 mVpp / 1 mVrms Normal Mode Current: <4 mArms Common Mode Current: <1.5 uArms Readback accuracy (@ 25C 5C), (% output + offset)Voltage: <0.05% + 5 mV (<0.1% + 25 mV for output 2 of E3646/47/48/49A)Current: <0.15% + 5 mA (<0.15% + 10 mA for output 2 of E3646/47/48/49A)
-
Product
DC Power Supply, 100 V, 0.4 A, 40 W
E36106B
DC Power Supply
The Keysight E36106B is an accurate, 100 V, 0.4 A, 40 W compact power supply for your bench or system.
-
Product
DC/DC Converter 10 W
EC6AW-110D15N
-
DC/DC converter with 10 W from Cincon | input ranges 43 - 160 VDC | outputs 15 V and -15 V | operates in temperature from -40 to +85 °C | according to EN45545-2 fire and smoke | negative control logic
-
Product
1100 HP Water Brake Chassis Dynamometer
TD-36
-
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 13,200 lb (5,987 kg)Capacity: 1,100 hp at 45 mph (820 kW at 72 kph)Rolls: 36 by 31 in. (915 by 787 mm) 4 fixed rolls to accommodate axle spreads from 48 to 74 in. (1219 to 1880 mm) tandem centersPit Required Depth: 35 in. (889 mm)
-
Product
AC/DC Clamp Meter
CM4374
-
• AC/DC Clamp • True RMS • 600/2000 A range • V, A, Hz, Ω, and other extensive measurement parameters • Inrush current • Max/Min/Avg/Peak • Wireless data download to a tablet or smartphone
-
Product
40W to 150W - Single Output
DT-D Series
-
*DoE, CEC and EISA Compliant*Energy efficiency level V and VI models*Wide Range AC Input
-
Product
Sound Level Meter
SM-2
-
Monacor International GmbH & Co.
Sound level meter (class 2), one-hand operation. Electret microphone capsule. Max hold and data hold function. A and C rating, slow and fast. Additional output for DC/˜V via 3.5 mm jack. Supplied with a practical nylon carrying bag.
-
Product
Programmable Step Attenuator, DC to 40 GHz, 0 to 70 dB, 10 dB Steps
84907L
Attenuator
The Keysight 84907L programmable step attenuator offers coaxial measurements to 40 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life greater than 5 million switching cycles per section) and an attenuation range of 0 to 70 dB in 10-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with with only 2,4 dB of loss at 40 GHz. The compact size of the unit, 35% smaller than the Keysight 8495/7 (26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
Product
Universal Copper Qualifier
ELQ 30A+
-
200 Hz to 35 MHz selective/wideband Level Meter & Generator, with Spectrum Analyser with Z/RL/LCL and Fault Locator Bridge
-
Product
DC/DC Converter 3.5 W
REM3.5E-4824S/R6/A/SMD
-
DC/DC converter with 3.5 W from Recom | input ranges 36 - 75 VDC | output 24 V | operates in ambient temperature from -40 to +95 °C | SMT package
-
Product
Universal Multichannel System up to 500V
-
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 500 V output voltage (0 ÷ 250 V, A1519B and A1619 only)- Maximum Current 0.5, 1, 10 mA or 1 mA/100 μA (dual range boards)- Individual Enable (A151x only)- Either DB37, DB25, Radiall Multipin or SHV connectors- Available with either positive, negative or mixed polarity- Up to 20 nA, 100 pA current set / monitor resolution- Up to 10 mV / 1 mV voltage set / monitor resolution- Very Low ripple, down to < 5 mVpp- 3 different channel grounding - Common Ground (AGxxxx) - Common Floating Return (Axxxx) - Full Floating (A151x, A1612, A1619)- Independently programmable for each channel: - Output voltage - Current limit - Ramp up/down - TRIP parameter- Current generator operation in overcurrent condition- Specific design for double side silicon detector (A151x)
-
Product
Digital Output Board, 32 Isolated Channels, 24V
APCI-2032
-
32 digital outputs, 24 V or 5 V, 500 mA/channel Optical isolation 1000 V Overvoltage protection Short-circuit protection WatchdogAt power-on the outputs are reset to ì0î
-
Product
Digital Panel Meters And Modules
-
Measuring Method TRMS using Microcontroller1A / 5A Input in same Meter (User Selectable)High Accuracy Accros the Entire Range9999 Count High Resolution DisplayDual Aux. 110 V AC and 230 V AC in same MeterUser Programmable Display / CTR / PTRAuto Selection of Decimal PointAuto Indication of KV & KASetup / Programmable Protected by Password
-
Product
Digital Multimeter
MM-2
-
Our compact, low cost Model MM-2 Digital Multimeter with True RMS is ideal for general electrical testing and troubleshooting. This full function multimeter measures DC voltage to 1000 V and AC voltage to 750 V, DC and AC current to 10 A and resistance to 400 Ohms. In addition to volts, amps and ohms, this meter includes audible continuity, diode, LED and transistor hFE tests. The rotary switch allows you to select from any of the functions quickly and easily.
-
Product
PXIe-4082, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter
783131-01
Digital Multimeter
PXIe, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter—The PXIe‑4082 is a high-performance 6½‑digit, 300 V DMM that provides the measurement capabilities found in two common test instruments: a high-resolution DMM and a digitizer. As a DMM, the PXIe‑4082 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, frequency, period, and basic L and C measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXIe‑4082 can acquire waveforms at sample rates up to 1.8 MS/s.
-
Product
Amplifier, Switch and Test Box
CLIOQC Model V
-
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
Product
Low-Profile 16-CH Isolated DI & 16-CH Isolated DO PCI Card
LPCI-7230
Analog Input Module
ADLINK LPCI-7230 is 32-CH isolated input and/or card. It provides a 2,500 C optical isolation protection. Two wide input range of the LPCI-7230 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The LPCI-7230 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automations applications. The LPCI-7230 also provides two interrupt sources on digital input channels, which are easily user configurable.
-
Product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785648-01
FlexRio Digitizer
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset. The PCIe-5774 is ideal for time-domain measurements in areas such as scientific instrumentation, medical imaging, and particle physics. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
600W Bench Electronic Load, Dual Input 150V, 60A, 300W
EL34243A
-
Keysight’s EL30000 Series bench electronic loads consist of three models, all with a built-in data logger. The EL33133A basic performance electronic load offers an economical price, a limited range, and a single 40 A, 150 V, and 250 W input. Two performance models offer additional ranges, the EL34143A single input 60 A, 150 V, 350 W, and EL34243A dual input 60A, 150V, 600 W.
-
Product
NI-9470, 5 VDC to 30 VDC, 8-Channel (Sourcing Output), 2 kHz C Series Digital Module
787089-01
Digital Module
5 VDC to 30 VDC, 8-Channel (Sourcing Output), 2 kHz C Series Digital Module - The NI‑9470 is a digital output module that features proportional valve drive control. You can use the NI-9470 to perform pulse width modulation (PWM), dither control, and current readback. The NI‑9470 features eight output channels compatible with signals from 5 V to 30 V and transient overvoltage protection between the output channels and the backplane.
-
Product
Standard Class AAA Solar Simulator
TriSOL TSS
-
Essential for testing virtually any material or product that is exposed to sunlight for long or short periods of time, OAI’s low-cost, Standard Solar Simulators deliver highly collimated, uniform light. Depending on configuration, output on these Solar Simulators is rated at 350W -5,000W.These Class AAA Solar Simulators feature OAI’s Advanced Uniform Beam Optics and are available with a choice of air mass filters to reproduce a wide range of solar spectra. For added flexibility, OAI’s proven lens and collimating mirror technology allows for a variety of exposure area sizes. A Class AAA Solar Simulator is an essential tool for manufacturing as well as R&D; it is indispensable in test labs, industry, and in universities. OAI Standard Solar Simulators are used in photobiology, biomedical, solar cell testing, cosmetic testing, and paints & coatings analysis. Based on 35+ years of proven UV light technology, OAI Solar Simulator Systems deliver repeatable, reliable, constant output, and measurement uniformity.
-
Product
Regenerative Power System 1000 V, ±90 A, 30 KW, 400/480 VAC
RP7982A
DC Power Supply
The RP7982A regenerative power system is a single output, bi-directional, regenerative DC power supply with safety features to protect your people and your DUT.
-
Product
Waveguide Gunn Oscillators
-
2 Models with Popular K and Ka Band Center frequencies of 24.125 GHz and 35 GHz. Designs feature mechanical tuning capabilty ranging up to + 3 GHz. Excellent Phase Noise Performance as low as -98 dBc/Hz typical. +10 dBm Output Power with Frequency Stability as low as -0.2 MHz/°C. Models have an Operational Temperature Range of -40°C to +85°C. Compact Aluminum Packages have Precision Machined Cavities that exhibit Optimum Performance. Fully Integrated Mil Grade WR-28 and WR-42 Waveguide Ports.
-
Product
SA2500X, 2.5 GHz, ±8 V, 10X Attenuation, Single-Ended Active Oscilloscope Probe
784257-01
Oscilloscope Probe
The SA2500X is single-ended, active voltage probe that is used for many different high-speed measurement applications. The probe is powered by an included auxiliary power supply that is internationally compatible and certified. You can use it with oscilloscopes that provide 50 Ω input impedance.
-
Product
8-CH Relay Output Module
ND-6063
Data Acquisition Module
- 8-CH relay outputs- Output Type: 8 Form A- Contact Rating: AC: 0.5 A / 125 V; DC: 1 A / 30 V or 0.3 A / 110 V; ON/OFF Interval Time: 3 ms- Breakdown Voltage: 500 VAC (50/60 Hz)
-
Product
SiC Diodes
-
ST’s silicon carbide diodes range from 600 to 1200 V – as single and dual diodes – and feature unbeatable reverse recovery characteristics and improved VF. Available in a wide variety of packages, from D²PAK to TO-247 and the insulated TO-220AB/AC, they offer great flexibility to designers looking for efficiency, robustness and fast time-to-market. ST’s SiC Schottky diodes show a significant power-loss reduction and are commonly used in hard-switching applications such as high-end-server and telecom power supplies, while also intended for solar inverters, motor drives and uninterruptible power supplies (UPS). ST’s automotive-grade 650 and 1200 V SiC diodes – AEC-Q101-qualified and PPAP capable – feature the lowest forward voltage drop (VF) on the market, for optimal efficiency in electric vehicle (EV) applications.
-
Product
PXI 32-channel High Voltage Data Acquisition
M9216A
Data Acquisition Module
The M9216A is a high voltage data acquisition module that allows simultaneous measurement of eight channels of positive voltages ranging from 1 mV to 100 V. Each channel comes with a concurrent 5 V and 100 V measurement range, with every channel capable of acquiring very low and very high voltages without the need for switching ranges.
