Stepper Motors
A device that translates electrical pulses into precise mechanical movement. The output shaft may deliver rotary or linear motion. (www.seanet.com)
-
product
Production Test Stands for Electric Motors
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
product
Electric Servo Motor Type 1 Axis Vibration Tester
In Addition, The System Configuration Requires At Least 3 Main Units, A Control Panel, And A Controller, And Does Not Require Hydraulic Units Or Blowers. The Exciter Can Perform Standard Tests And Performance Tests Required For Automobile Seats Based On An Electric Servomotor Type Multi-Axis Vibration Tester.
-
product
Motorized Force & Torque Measurement Test Stands
Mark-10 offers a wide and unique range of motorized force measurement and torque measurement test stands. Motorized stands offer a significant advantage over manual test stands by providing constant test speed. Some models can be programmed for advanced test sequences to accommodate demanding applications. All motorized test stands carry the CE mark. A test stand is an integral part of a testing system, typically also comprising a force gauge or torque gauge, grips, software, and accessories.
-
product
Motor Starting & Control Resistors
Motor Starting Resistors are used to reduce the voltage at the motor terminals and also decrease the starting current. Motor Starting Resistors are necessary because the self resistance of a motor armature is very low. When the voltage is first applied, excessive current will flow. For limiting this current, since there will be no resisting back electromotive force (emf),some series resistance can be added to the armature windings.
-
product
Control Board for Motor, Pump & Valve
F1V04
Beijing SANKI Petroleum Technology Co., Ltd.
The main board issues a start signal and a low voltage signal (12v) for opening the electromagnetic valve, which are converted into strong voltage signals (220 VAC) to drive the electromagnetic valve (380 VAC) and the motor in our fuel dispensers system, thus completing the function of conversion from weak voltage power to strong voltage power. The control board circuit isolates high voltage interference signals via photoelectrical isolating components.
-
product
Motors and Resolvers
We design, manufacture and test highly reliable motion control devices for extreme environments that range from vacuum and the extreme cold of outer space to high pressure and temperature applications many miles under the earth's surface.
-
product
Brushless Motor Tester
Shanghai Aoboor Electric Co., Ltd.
Applicable for testing general properties of DC brushless motors.
-
product
Safety Rated Servo Motors And Drives
Advanced motion safety functions including SLS, SLP and SS2 allow to complete a risk reduction strategy, and reduction in machine downtime while improving maintenance and changeover efficiency.
-
product
Saluki SFS-2000 Fusion Splicer (4 motors)
SFS-2000 series is the new standard 4 motors fusion splicer. Light Weight, Touch Screen, Friendly UI, Fast Fusion and Heating, makes it very popular and hot.* 7s fast splicing, 14s highly efficient heating* 320/88 times image magnification, 5mm fusing for ultra-short cleave length* 10000 groups of fusion records storage* 300 groups of splice modes, 100 groups of heating modes* 220 counts of splicing and heating cycles with build-in 6800mAh Li-on battery
-
product
Static Electric Motor Analyzers
Baker Instruments’ static motor test equipment is the industry-leading suite of products for detecting weaknesses and faults in the insulation systems of electric motors, generators and coils. Employing both low-voltage and high-voltage tests – such as Baker’s signature surge test - these essential troubleshooting and predictive maintenance tools allow maintenance professionals to assess any need to maintain or replace specific motors and generators that support their business. Equally at home in the motor repair shop or on a plant floor, these testers ensure that the electrical condition of your rotating machinery is understood.
-
product
High & Low Temperature Impact System for ATF Cooling Motor
EVTP-30
Shanghai Dean Electrical Co., Ltd
This test system provides the most direct life evaluation of ATF cooling based EV motor by simulating the temperature impact from ultimate self- heating of the motor and severe cold condition from environment.
-
product
Saluki SFS-2000H Fusion Splicer (6 motors)
SFS-2000H series is the core-to-core alignment (6 motors) fusion splicer. Light Weight, Touch Screen, Friendly UI, Fast Fusion and Heating, and more intelligent. The rich functionality and ultra-low splice loss make the splicer adaptive to fiber splicing in various environments.* Core to core alignment (6 motors)* 7s fast splicing, 14s highly efficient heating* 320/200 times image magnification, 5mm fusing for ultra-short cleave length* 10000 groups and 100 images of fusion records storage* 300 groups of splice modes, 100 groups of heating modes* 300 counts of splicing and heating cycles with build-in 6800mAh Li-on battery
-
product
Motor Quality Control Test Systems
SKF Condition Monitoring Center
These rack-style motor quality control units are rugged, field-proven systems for testing stators and armatures in high-volume manufacturing environments. They combine the most common electrical tests into an efficient automated solution.
-
product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,200mm
C_MBT C 4.0 W220 | VP 210156
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and Vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,200 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes with high vehicle throughput and increased loads.
-
product
Modular Low Voltage Motor Protection
LM10
The GE Multilin LM10 Low Voltage Motor Protection System is a modular device for low voltage motor protection. The compact design of the LM10 is ideally suited for Low Voltage Motor Control Center applications but can also be used in standalone applications. The LM10 comes standard with the DeviceNet protocol that allows the user to control and monitor the relay over a network. The relay also has an interface port to communicate with the optional LM10 Programmable Display Unit (PDU).
-
product
Fully Automatic Full Load (Routine) Testing Panel For Induction Motor
Aarohi Embedded Systems Pvt. Ltd
Aarohi introduced fully automatic routine testing panel. The primary purpose of the routine test is to insure freedom from electrical and mechanical defects, and to demonstrate by means of key tests the similarity of the motor to a “standard” motor of the same design. this panel also help to enhance productivity, Work efficiency & reduces need for skill operator. More then 500 Indian pump manufacturer ware installed this system & satisfied with performance.
-
product
Laser Spectroscopic Motor Exhaust Gas Analyzer
MEXA-ONE-QL-NX
The MEXA-ONE-QL-NX is an analyzer for the direct, simultaneous real-time measurement of the four relevant nitrogen-containing exhaust gas components NO, NO2, N2O and NH3.The analyzer combines a light source based on the new quantum cascade technology (efficient lasers in the mid-infrared spectral region) with a precisely adjusted dual path cell to measure low concentrations with maximum sensitivity. The detection limit complies with current European legal requirements.Furthermore, the MEXA-ONE-QL-NX offers wide measuring ranges of up to 5000 ppm (for NO). By using extremely narrowband light sources and measuring under reduced pressure the cross-sensitivity to other exhaust gas components can be drastically minimized.The complete measuring system - including filtration - is specifically developed for the measurement of NH3 and thus guarantees a very fast NH3 rise time (T10-T90) of less than 5 seconds. The MEXA-ONE-QL-NX can be operated as a stand-alone analyzer or integrated into the MEXA-ONE software interface for user-friendly and simplified system operation.
-
product
Motor Starters
Mitsubishi Electric Automation, Inc
A type of starter for AC motors that combines a magnetic contactor and an overload relay. The MS-T (10-32 amps) and MS-N (35-400 amps) series motor starters offer a compact design and provide reliable protection for your motors against overload and short-circuit conditions in any industrial application.
-
product
Motor Protection Meter
MPM
The MPM provides additional metering capabilities such as three phase voltage, pf, real power, reactive power, Wh, and frequency for the 269 or 269 Plus Motor Management Relay.
-
product
Motor Tester and Analyzer
ITIG
The iTIG III is the industry’s most advanced electric motor tester and winding analyzer. Bringing confidence to motor repair companies, industrial end users, OEMs, and manufacturers of rotating equipment, the iTIG III features over 20 high- and low-voltage tests including high frequency surge and partial discharge.Choose multiple tests to run automatically in a sequence or select single tests. Report results with the easiest to use instrument available. Manually operate voltage dial or set up for automatic operation. Carry the iTIG III in the field or use it as a benchtop device. Connect to an external portable power pack for testing up to 40kV. The iTIG III is the most versatile and easy-to-use tester available.
-
product
Hall Motor Tester
Shanghai Aoboor Electric Co., Ltd.
Applicable to no-load test and any DC motor with internal hall elements.
-
product
Development Test for Electric Motors with Power Electronics
Test bench for electric machines and inverters in hybrid applications*Control of mechanical parameters*Verification of electrical properties*Checking the LL characteristics*Short circuit measurement*Recording the performance process*Noise measurement*Temperature measurement
-
product
Motor Vehicle Headlight Testers
Foshan Analytical Instrument Co, Ltd.
It can be used to promptly and accurately measure the luminous intensity and the illuminating position(or the optical axis deviation amount) of the high/low beam of vehicle headlight. With the lamp image alignment techique the single-machine high/low beam testing needs only 30-odd seconds.It is also used for the dual-lamp test at the testing station,the dual-machine test at the same time needs only 20-odd seconds.
-
product
Motorized Test Stands
The Chatillon motorized test stands are optimized for production floor operation.
-
product
Motorized Test Stands
AMETEK Sensors, Test & Calibration
Our motorized test stands are optimized for production floor operation. They provide a constant test speed and require a force gauge to be integrated with the test stand.
-
product
Motor Octane Testing
DewTrak II MO
DewTrakII MO dew point/humidity transmitter is an optical chill mirror hygrometer designed to continuously measure the moisture content and Barometric pressure in the motor octane testing process. It is used to monitor and ensure compliance with test
-
product
Direct Drive Motors And Motion Systems
HEIDENHAIN offers the largest direct drive motor range on the market via ETEL. Solutions range from high-end motion systems with nanometer precision to industrial applications requiring high torque. And like HEIDENHAIN, ETEL builds its linear and torque motors, along with motion systems, on a foundation of superior knowledge and technical expertise, disruptive technology and tireless quality control. Customers reap the benefit: the most cutting-edge, reliable and precise motion control solutions available.
-
product
AC And DC Motors
Omega's AC and DC motors are built to deliver reliable long-term performance. With a variety of models available, we have motors for all your application's needs.
-
product
Drivetork ST motorized torque tester for safety cap
DRIVETORK ST
Besides having all the functions of the Drivetork Easy, the Star version can also carry out the rupture test when the cap has a security ring. It measures both the break (first peak) and the opening torque (max torque), and it displays the test curve.
-
product
Terminal Board With 100-Pin SCSI-II Connector For General Purpose Servo & Stepper
DIN-825-4P0
- Supports specific servos & steppers by cable selecting- On-board connector type: 100-pin SCSI-II- Dimensions: 300 mm x 107 mm x 44 mm (W x L x H)
