VME Chassis
-
product
LS-28-1U Chassis Cable Assembly Set
28U-CBLSET
Cable assembly set for LS-28-DRSM 1U Rack Mount Unit
-
product
VME J1J2 Monolithic 6 slot
101VMEM106-0500R
VME J1J2 Monolithic backplane 6 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
Chassis Mounting Kit
63-924-001
This chassis mounting kit is designed for use with the our 8-slot PXI chassis (40-924) and our 7-slot LXI modular switching chassis (60-102D), allowing installation into a standard 19" rack.
-
product
Module for VME & VXI Systems
EXC-4000VME/xx / EXC-4000VXI/xx
The EXC-4000VME/xx and EXC-4000VXI/xx cards for VME & VXI systems supports up to eight dual redundant MIL-STD-1760 channels using the M4K1553Px(S)-1760 module and is compatible with all common variations of MIL-STD-1760 (A, B). Each channel can operate simultaneously as a Bus Controller and up to 32 Remote Terminals and as a Triggerable Monitor. In addition, Checksum, SRQ bit and Header Words are supported on each channel.
-
product
Chassis, Carriers And Controllers
Automated measuring systems based on the open standards AXIe, VXI, LXI and PXIe have enclosures (base units or chassis) in which modules of a given standard are mounted. Informtest Holding manufactures a wide range of chassis in open standards AXIe, VXI, LXI and PXIe.
-
product
64-Channel VME Relay Module
V210
The V210 is a single-wide, 6U VME module that includes 64 SPDT relays and drivers. User-settable DIP switches set the A16/A24 VME address mode, VME address, and select whether the relays are statically operated or operate in latching mode, where relay states are sustained when VME crate power is off.
-
product
Chassis Dynamometer Smoke Testers
A chassis dynamometer smoke tester (CDST) is used to test diesel emissions when the engine is under load. This is of course a much more realistic test than the commonly used free acceleration test. It is also better for the diesel engine.During a CDST test an automatic test cycle is performed, whereby the emission is measured at different engine loads. The monitor shows checks and actions to perform before the test, shows real-time measuring data and instructions for the driver during the test, and the end results after the test.
-
product
VME J2 3 slot
101VMEJ203-0900R
VME J2 backplane 3 slot, compliant with ANSI/VITA 1-1994. The A+C rows are bussed in all slots. Also, row B has onboard, inboard termination.
-
product
VME to USB 3.0/Ethernet/Optical Link Bridge
VX4718
The VX4718 is CAEN New Bridge with enhanced data rate and extended interfacing capabilities, thanks to the on-board MPSoC (including an ARM processor running Linux). The board is a VME Master which can be controlled by an external PC via USB 3.0 and Gigabit Ethernet connections.
-
product
6U Single VME Slot Intelligent Interface Card
IIB-3910-VME-2C
The IIB-3910-VME-2C is a 6U single VME slot intelligent interface card providing complete STANAG 3838 andSTANAG 3910 test, simulation and bus analysis capability, for two 3838 dual redundant and two 3910 buses, which support optical dual redundant and electrical single redundant 3910 protocols.
-
product
VME Modules
VME is a high speed and high performance bus system with powerful interrupt management and multiprocessor capability. It was created by combining VERSA-bus electrical specifications (1979) with the Euro-card format resulting in the VME-bus Revision A - 1981 specification.
-
product
2U Rackmount Chassis For ATX/Micro ATX/Mini-ITX Motherboard
AX61223TM
*Supports ATX/Micro ATX/Mini-ITX motherboard*Supports ATX power supply*Internal one 3.5" HDD drive bays*Front-accessible one 3.5", one 5.25" HDD drive bays and one slim CD-ROM bay
-
product
VME Module
ICC-8-xxx
The ICC-8-xxx is the second generation of the ICC-8 board. Enhancements includes true RS-485 communications with jumper configurable I/O by the user. The ICC-8-xxx is a VME based, 8 channel intelligent and versatile solution to serial data communications designs.
-
product
VME J1 8 Slot with ADC Connectors
101VMEJ108-0590
VME J1 backplane 8 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
2U Rackmount Chassis with 1U ATX Power Supply
cPCIS-6230R/ 6240R Series
The cPCIS-6230R and cPCIS-6240R Series sub-systems are designed for 6U cPCI boards with 80mm RTMs and are suitable for computer telephony applications. The chassis is 2U height and standard 19" rack mount width.
-
product
2-Axis High-Resolution Laser Axis Board for VME
10898D
The 10898D 2-axis high-resolution laser axis board provides the same resolution as the Keysight 10897D high-resolution laser axis board with increased slew rates and reduced noise. The increased stage velocity limits and low noise compared to previous laser systems offer premium positioning repeatability and accuracy for advanced applications such as IC fabrication equipment.
-
product
VME J2 12 slot
101VMEJ212-0900
VME J2 backplane 12 slot, compliant with ANSI/VITA 1-1994. The A+C rows are bussed in all slots. Also, row B has onboard, inboard termination.
-
product
Chassis - Built as 60 or 75 ohm Matrix Configuration Switch Modules for High Bandpass
CXG Matrix
These Chassis are built as 50 or 75 ohm matrix configurations of 4x8 or 8x8 using tree switch configuration switch modules for high bandpass. The internal matrix block is wired out to BNC, SMA or other 50 or 75 ohm connectors. LEDs on the front panel show switch and power status. Add a Control Module to complete the system.
-
product
NI-9157, 14-Slot, Virtex-5 LX85 FPGA, MXI-Express CompactRIO Chassis
781316-01
14-Slot, Virtex-5 LX85 FPGA, MXI-Express CompactRIO Chassis - The NI‑9157 is a rugged MXI‑Express chassis for high-performance, high‑channel‑count applications. With the NI‑9157, you can add C Series I/O modules to your PXI system or industrial PC. You can daisy chain up to six NI‑9157 chassis in a single chain and connect up to eight chains to a single controller.
-
product
96 Channel I/O and 64 Channel I/P VME Module
DP-VME-3132
The DP-VME-3132 provides 96 channel RS422 differential digital I/Os and 64 channel RS422 differential isolated inputs on the front end and rear side. On the rear side, it is interfaced with the VME 64x backplane.
-
product
VME Test Extender 6U/220mm J1/J2
111EXT6122-012X
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
VME Processor Cards
Curtiss-Wright Defense Solutions
We believe upgrading VME systems with the latest processing technology and security capabilities shouldn't require a complex and costly redesign. That's why our VME single board computers (SBCs) are designed with contemporary processors, Trusted Computing features, and pinouts that are compatible with older VME boards.
-
product
6 Channel 4 kV/3 mA VME HV Power Supply Module
V6533
The V6533 is a 1-unit wide VME 6U module housing 6 High Voltage Power Supply Channels 4 kV, 3 mA (9W max). The board is available with either positive or negative output polarity; mixed version with 3 positive and 3 negative channels is also available.
-
product
VME Controller With USB-2 Interface
VM-USB
The VM-USB is a VME master with high speed USB2 interface. Enhanced functionality is given by the programmable internal FPGA logic which provides a VME command sequencer with 4kB stack and 28kB data buffer. Combined with the 4 front panel I/O ports this allows VME operation and data acquisition / buffering without any PC or USB activity.
-
product
Chassis Rugged Slide Rail Size 7
CAE016384
Securely locked in extended position. The chassis/cabinet mounted slide rails are ultra rugged and hold significantly more weight and can withstand shock and vibration in harsh environments.
-
product
CompactPCI Chassis 2 Slots
Hartmann CompactPCI 1U system platform provides an intelligent, practical packaging solution for high-performance processors. The full width rack mount model provides a 2 slot 5V I/O 6U cPCI backplane for horizontal mounting of boards. This system is designed with enhanced EMC features.
-
product
Chassis Dynamometers
Is a device used for vehicle testing and development. It uses a roller assembly to simulate a road in a controlled environment, usually inside a building.
-
product
PXIe-1090, Thunderbolt™, 2-Slot (1 Hybrid Slot), Up to 2 GB/s PXI Chassis
787040-01
PXIe, Thunderbolt™, 2-Slot (1 Hybrid Slot), Up to 2 GB/s PXI Chassis - The PXIe‑1090 features a high-bandwidth backplane to meet high-performance test and measurement application needs. This PXI chassis features one hybrid connector, 58 W power and cooling, and an integrated. Thunderbolt 3 MXI-Express controller. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the US and/or other countries.
-
product
CompactPCI Chassis
CompactPCI is a standard in computer bus technology for industrial computing that utilizes a Eurocard type connector combined with PCI signaling and protocols. cPCI boards come in 3U and 6U variants and are typically interconnected through a passive backplane. The connector pin assignments are standardized by PICMG , allowing for eight boards in a PCI segment with multiple bus segments being allowed with the use of active bridges.
-
product
EtherCAT Chassis with EtherCAT Bus-Coupler
EPS-9905 with EPS-6000
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
