Radio
Transmission of modulated electromagnetic waves whose frequency falls below light.
See Also: Software Defined Radio, Radio Frequency, Ham Radio, Mobile Radio, Radio Analyzers
-
product
Microwave Switch RF Switch - 26.5G AXIe
RF Switch-26.5G AXIe Module
The RF Switch-26.5G AXIe module is designed to work as part of information measuring systems as a radio frequency signal switch (one input to six outputs for each of the eight input lines).
-
-
product
FREQUENCY DISPLAY UNIT
TYPE NFD-1
The National RF Type NFD-1 Frequency Display Unit was designed for use with vintage and classic communications equipment, to display the received or transmitted radio frequency. The unit incorporates an internal processor that allows the intermediate frequency (IF) to be counted out by the frequency counter. The resultant display is the actual frequency that the equipment is receiving or operating at.
-
product
Monitors
Off-air monitoring and + demod/metering equipment for AMFMHD-Radio DBA+ Internet Radio.
-
product
6-24V Heavy Duty Circuit Tester
1652
Peaceful Thriving Enterprise Co Ltd
Check on 6-24V systems. For use on lights, starters, alternators, cooling and heating components, radios and relays.
-
product
AERINOS Sigfox IoT
Infinite Industrial Informatics Lt
Sigfox is a communication protocol that is used to read data from sensors through a fixed network of base stations. It works like a low cost “SMS” service. As an end-user, you only need to buy a subscription to connect to the data network operated by SIGFOX. Sigfox employs a proprietary Ultra Narrow Band (UNB) radio technology that enables communication using the Industrial, Scientific and Medical ISM radio band, which uses 868MHz in Europe and 902MHz in the US. It has the advantage of covering larger areas than other fixed local systems.The overall Sigfox network topology has been designed to provide a scalable, high-capacity network, with very low energy consumption, while maintaining a simple and easy to rollout star-based cell infrastructure. The density of the cells in the Sigfox network is based on an average range of about 30-50km in rural areas and in urban areas, where there are usually more obstructions and noise is greater, the range may be reduced to between 3 and 10km.According to the latest numbers, Sigfox has a nationwide live coverage in 6 countries and in 14 other countries it is deploying and rolling out ts network. By end 2018, the ambition is to cover 60 markets.
-
product
Aerospace
Radiometrics Midwest Corporation
Working with the Radio Technical Commission for Aeronautics, Radiometrics staff has not only been involved with EMC testing of aircraft and aircraft components, but has also been involved with development of the RTCA/DO160 "Environmental Conditions" standard and RTCA/DO-199 investigation for "Potential Interference to Aircraft Electronic Equipment from Devices Carried Aboard".
-
product
EMC Tests
Electromagnetic compatibility (EMC) must be demonstrated for all devices with integrated radio components for approval in almost every country in the world. EMC tests examine whether the electromagnetic emissions from your product are within the specified limits and whether your product and its functionalities themselves are not negatively influenced by electromagnetic emissions. We offer EMC tests for modules and end products with integrated radio technology as well as IT and IoT products. Our accredited EMC test laboratories are equipped to test almost all modern radio technologies, and our EMC experts have many years of experience in this area. With us, your modern radio products are on the safe path to the global market.
-
product
Benchtop Communication Test System
ATS3000A
The ATS3000A is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23 instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000A also includes the sophisticated IF and baseband I/Q Digital Signal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easy-touse graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets areavailable for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
product
4-Channel 200 MHz A/D with DDC, Virtex-6 FPGA - XMC
Model 71661
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs- Multiboard programmable beamformer- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Antenna Switch
SixPak
The SixPak has two components: a relay matrix and a control box, there are several options for the controller.The relay matrix allows the selection of any 6 antennas by 2 radios or feedlines. Its lockout circuitry prevents both radios from selecting the same antenna. (The 6x1 type of SixPak is now replaced by our RatPak remote 6 way antenna switch.)The usual set-up has one SixPak dual rotary control box, which is manually operated from the radios positions. The control box for the 6x2 contains two rotary switches and 12 LEDs, so the operator can see which antennas are selected.
-
product
2-Ch 500 MHz A/D w/ DDC & 2-Ch 800 MHz D/A w/ DUC, Virtex-6 FPGA - 3U VPX
Model 52651
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- Two 800 MHz 16-bit D/As- One DUC (digital upconverter)- Multiboard programmable beamformer- Up to 2 GB of DDR3 SDRAM or 16 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
1-Ch. 6.4 GHz or 2-Ch. 3.2 GHz A/D, 2-Ch 6.4 GHz D/A Kintex UltraScale - XMC
Model 71141
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- One-channel mode with 6.4 GHz, 12-bit A/D- Two-channel mode with 3.2 GHz, 12-bit A/Ds- Programmable DDCs (Digital Downconverters)- Two 6.4 GHz, 14-bit D/As- Programmable DUCs (Digital Upconverters)- 5 GB of DDR4 SDRAM- µSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction cooled versions available- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
Multicoupler
Receiver (RX) multicoupler by novotronik are used whenever a common signal from antennas, signal generators or reference clocks has to be distributed to several radio receivers, spectrum analysers or radio scanners. Incoming signals are transmitted without attenuation losses. In addition to our standardized RF devices, we also know to convince in the realization of your individual requirements.
-
product
EMF Measurements Antennas
An isotropic antenna that allows to carry out radiated emission and environment exposure measurement (elettrosmog) to the radio frequencies in proximity of radio and television stations and repeaters for mobile telephone.
-
product
Sensor Device for Developers
Waspmote
Libelium Comunicaciones Distribuidas S.L
Ultra low power (7µA)120+ sensors integrated on 10 Sensor Boards15 radio technologies:Long range: 4G / 3G / GPRS / LoRaWAN / LoRa / Sigfox / 868 MHz / 900 MHzMedium range: ZigBee / 802.15.4 / DigiMesh / WiFiShort range: RFID/NFC / Bluetooth 2.1 / BLEOver the Air Programming (OTA)Encryption libraries (AES, RSA, MD5, SHA, Hash)Certified encapsulated line (Plug & Sense!)Industrial Protocolos: RS-232, RS-485, Modbus, CAN Bus, 4-20mA
-
product
IPD RF Components – LTCC
Pulse’s complete offering of LTCC based Band Pass Filters, Balun’s, Diplexer’s and Couplers used in conjunction with our wireless antenna products will enhance your devices performance keeping attenuation and noise to a minimum. Many of Pulse’s IPD components are already qualified or referenced on various radio designs, so please contact us about the components already qualified on the radio you are using. From Wifi Networking devices, to smart phones and tablets, Pulse’s offering of IPD Components has you completely covered. Using the table below you can search our complete IPD Component offering.
-
product
Remote Indicator System
LineTroll R110CQ
The fault indicator use a 2.4GHz ISM band short-range radio to communicate with the collector mounted on the pole. The collector communicates with up to 9 fault indicators. Both the indicators and the collector are powered by long-life lithium batteries for long and maintenance free operation.
-
product
USB-Mini Type B (Extended With Shielding) Test Connector
Test connector for Mini USB type B extended with shielding (5 pole) for contacting Mini USB Interfaces. Application in smaller Mini-USB devices like cameras, mobile phones, radios, hard disks etc. Comes in two versions.
-
product
Low Noise Amplifiers for Radio Amateurs
Our Low Noise Preamplifiers are remarkable for extremely low noise, excellent SWR, high efficiency and a high IP3. The Low Noise amplifiers are especially selective and absolute stable therefore oscillation is avoided. Even if you have a bad SWR. This is the reason why radio amateurs and club-stations all around the world trust in Kuhne electronic equipment. The products are perfect for use in contests, EME, MeteorScatter, Aurora and Tropo DX. Small mechanical measurements and technical innovations from the professional sector, e. g. milled aluminium cases, enable high temperature stability and tower mounting. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Don't compromise and get technology from Kuhne electronic!
-
product
Tunable Notch Filters
The Ranatec Tunable Notch Filters are critical tools for adaptation to stringent new ETSI/3GPP conformance test specifications for mobile device radio properties, that covers all sub-6 mobile bands and channel bandwidths for 2G/3G/4G/5G. Designed for formal conformance testing performed by accredited test houses, as well internal verification by mobile device vendors. A flexible and easy to use test automation platform to support almost any ambition level, tailored to your demands.
-
product
Microwave Radio
The transmission of signals via radio waves using a series of radio wavelengths measured in small numbers of centimeters.
-
product
Channel Replicator
Series 7000
The Series 7000 System is a multi-radio test network which replicates the propagation path of real-world applications. With complete bi-directional capability radios may operate in full duplex mode at distances up to 150 nautical miles.
-
product
ICE 4000 Series
ICE4003
The ICE4003 is a dual channel filter that provides two independent UHF TX/RX channels in a single package. Each channel can operate autonomously into a dedicated antenna or both channels can be combined into a single antenna. Furthermore, the combiner used in the ICE4003 is capable of combining any combination of TX/RX signals while minimizing path loss. Currently, supported radios include the ARC-225 and ARC-210. The ICE4003 is designed with a flexible interface to support future radio requirements, such as JTRS. A mounting tray is available as an option for easy incorporation on your platform. Cost-effective modifications are available on the ICE4003. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.
-
product
RF & Microwave PXI Switch Modules
These switching systems are used for design validation, reliability and production test including 5G, SD radios, S parameter testing for RF cables, antennas, radar and semiconductor verification.
-
product
8-Channel 250 MHz A/D with DDC, Kintex UltraScale FPGA - PCIe
Model 78131
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Eight 250 MHz 16-bit A/Ds- Eight multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized versions available
-
product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - 3U VPX
Model 52751
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional user-configurable gigabit serial interface- Optional LVDS connections to the FPGA for custom I/O- Optional 400 MHz 14-bit A/Ds- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Radio Transmission
ARF868 MR
Increase the range of radio transmission, for broadcast over long distances.
-
product
MIPI Radio Front-End
RFFE
Mobile phone radios have developed into highly complex, multi-band and multi-standard designs that often have multiple radio frequency (RF) signal chains. The MIPI Alliance Specification for RF Front-End Control Interface (RFFE) was developed to offer a common and widespread method for controlling RF front-end devices. The RFFE Master IP core typically resides in the RFIC in a mobile platform, and utilizes the RFFE bus to identify, program and monitor the registers in RF front end Slave devices through programmed IO. It is designed to support existing standards such as LTE, UMTS, HSPA and EGPRS, and is usable in configurations ranging from single Master/single Slave to multi-Master/multi-Slave.
-
product
CPRI Interface Panel Kits for Connectivity Testing
RFS’ CPRI Interface Panels are used to test fiber connectivity between Optical Base Band Units (BBU) and Remote Radio Heads (RRH), allowing cell operations and system performance engineers to ensure the best performance without having to disconnect the fiber optical system or disrupt service. In addition, the CPRI panel enables easy RF over CPRI testing at the bottom of the tower, reducing the need for unnecessary tower climbs, thus minimizing maintenance cost and overall OPEX for customers. The RFS CPRI panel is bundled with RFS’ high-quality fiber optic jumpers, providing an end-to-end solution that includes HYBRIFLEX® fiber-to-the-antenna DC and F/O solutions.
