PD Monitor
-
Product
UHF PD Detector
-
Handheld online PD substation surveying system. The UHF PD Detector is the ideal tool for quick, non-invasive surveys in MV and HV substations and should be part of the toolkit for all maintenance and service teams. Due to its high measurement bandwidth, the UHF method provides accurate local online partial discharge (PD) measurements on HV components such as cable end-terminations, surge arrestors, voltage transformers and isolators.
-
Product
Linear Polarization Resistance (LPR) Monitoring
-
The electrochemical technique, commonly referred to as Linear Polarization Resistance, is the only corrosion monitoring method that allows corrosion rates to be measured directly, in real time. Although limited to electrolytically conducting liquids, the response time and data quality of this technique make it clearly superior, where applicable, to all other forms of corrosion monitoring.
-
Product
PD Measuring System
TEM
-
Partial discharge test system for laboratory or on-site measurement according to VDE 0434, IEC 60270 and EN50178 consisting of:*Partial discharge meter TMG*High-voltage coupling capacitors for decoupling of the PD pulses*Partial discharge calibrator TPK for determining the correction factor in the PD test circuit
-
Product
External Pyrometric Camera for Combustion Thermal Monitoring
PYROSCAN-U
-
Pyroscan-U is specifically designed to perform thermal monitoring and mapping of any object inside a kiln, furnace, boiler or reactor, while looking at the area of interest through a standard window, from outside the combustion chamber. This megapixel pyrometric camera captures both visible and infrared HDR (High Dynamic Range) images of the burning zone.
-
Product
Handheld Online PD Detector
PD-SGS
-
Quick identification of PD activities in switchgear and cable accessories. The BAUR PD-SGS handheld online PD detector is used to conduct rapid initial tests for PD activities on live switchgear. Potential weak points are immediately signalled acoustically and numerically.* Initial rapid condition evaluation of switchgear and cable accessories during mains operation* Ideal for quick checks of MV and HV switchgear* Two integrated sensors:TEV sensor records PD on the surfaces of switchgearsAcoustic sensor records PD inside switchgears* Greater safety for test personnel switchgear tested for safety risks before starting work
-
Product
Gas Monitor
Toxgard® II
-
Simply connect the convenient ToxGard II Gas Monitor to a power source and a remote sensor, and it's ready to detect toxic gases, combustible gases and oxygen deficiency. The indoor/outdoor unit is housed in a rugged NEMA 4X enclosure and features a large LED screen, three levels of alarm and a failsafe fault relay output.
-
Product
Surface Contamination Monitor
IMI Inspector Alert™ V2
-
The IMI Inspector Alert™ V2 measures alpha, beta, gamma and x-radiation using a 2-inch “pancake” GM detector with high sensitivity to common beta and alpha sources. The easy-to-read digital display shows readings in your choice of µSv/hr, mR/hr, CPM, or CPS. The Total/Timer feature allows timed readings from one minute to 40 hours for precise measurement of low level contamination. An audible alert sounds when the radiation reaches a user-adjustable level.
-
Product
Charge Plate Monitors
-
Our easy-to-use charge plate monitors allow you to accurately evaluate air ionization systems used to neutralize static charge accumulation. Benefit from our economical solutions and products that offer onboard data storage to automate ionization system testing.
-
Product
Dielectric Cure Monitor
LT-451
-
The LT-451 Dielectric Cure Monitor is a versatile instrument designed for research and development, quality assurance/quality control, and manufacturing applications involving thermoset materials such as resins, composites, and paints and coatings.
-
Product
Monitors
-
Whether you need a local display, alarm and shutdown capability, data recording, and the ability to communicate using Modbus over Ethernet TCP/IP; or you need to trend waveform and transient data to provide a predictive look at your machine’s condition, Metrix has a solution to meet your machinery monitoring requirements.
-
Product
Dissolved Oxygen Concentration Monitor Series for Semiconductor Manufacturing
HD-960LR
-
Ideal for measuring dissolved oxygen concentration in Wet Process from Front-end of Line to Back-end of Line.By adopting a chemical resistant sensor, it is possible to support a wide range of dissolved oxygen concentration measurements from facility to process usage.
-
Product
Heavy Duty Vibration Monitor
VUM-800
-
Features • Heavy-duty sensing probe • DPDT 10 amp relay • Optional 230 VAC operation • Control unit remotely mounted • Failsafe operation
-
Product
In-line Sensor & Auto Range Switching Concentration Monitor
HF-960EM
-
Measures a wide range of HF concentration from low concentration to undiluted liquid. The HF-960EM achieves high precision measurement by the auto-correction range switching function. Also has the capibility of cleanliness with all PFA sensors. Measurement range: 0 - 50%.
-
Product
Mill & Silo Monitoring System
MSM-100
-
MSM-100 is a monitoring system specifically designed to continuously detect carbon monoxide(CO) in pulverizing mills. The high level of CO produced by any incomplete combustion process, is used by the MSM-100 system as advance warning of a mill fire. It is suitable for any coal or peat system where advance warning of spontaneous combustion is required. MSM-100 is intended for operation in the electricity, metals, cement, steel and processing industries.
-
Product
Helicopter Reducer Vibration Monitor
-
The complex is built on the basis of the measuring platform NI PXI and provides measurement and calculation of vibration parameters. The software of the complex is two-level: the lower hardware level and the upper level of the user interface. The hardware level software provides the following functions:interrogation of measuring modules;signal processing in the time domain;calculation of measuring parameters;spectral analysis;recording the signal to the hard disk.
-
Product
Medical Monitor
-
ADLINK Surgical Monitor (ASM) series of surgical monitors is designed to easily integrate with medical imaging systems, like endoscopic, laparoscopic, microscopic, fluoroscopic, and multi-modality. They can be used to visualize videos and still images in operating theaters, intensive care units, and emergency and examination rooms.
-
Product
Continuous Surface Current Mapping & Wave Monitoring System
SeaSonde
-
The SeaSonde HF radar system by CODAR Ocean Sensors is your solution for making continuous, wide-area ocean observations. The SeaSonde will provide you with years of real-time data over large coverage areas, with ranges up to 200 km — This is not possible with any other technology!
-
Product
Power Supply and Current Monitor
DC Connect
-
DC Connect enables measurement of current consumption of battery operated and other low voltage devices such as hearing aids
-
-
Product
Load Monitoring Units (LMUs)
-
Magtrol's Load Monitoring Units are used for measuring load, force and weight from signals generated by strain gauge transducers. Specifically designed for use with Magtrol's Load Measuring Pins and Load-Force-Weight Sensors, the LMU Series provides excitation voltage while conditioning the bridge output signal. Each unit contains DIP-switches and jumpers for greater flexibility and complete adaptability
-
Product
Optical Channel Monitor
-
Optoplex Optical channel monitor (OCM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical channel monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controling network elements so as to optimize operational performance. In particular, Optoplex Optical channel monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength, power, and optical signal-to-noise ratio (OSNR). See the following schematic diagram for OCM working principle.
-
Product
Monitoring Devices
-
TDK Monitoring Devices - rf shielded hd video camera, rf shielded hd mini video camera, camera controller
-
Product
A Serial Data Link Monitor for Windows
Listen
-
Listen is a Data Link monitor designed to assist debugging & troubleshooting serial communications links. Listen utilizes standard Windows COM port drivers to tap into RS-232 transmit signals for monitoring bi-directional communications between two devices.
-
Product
Online Noise Monitor
AWA5636-3
-
Hangzhou Aihua Instruments Co., Ltd.
Complies with IEC 61672 Class 2. Uuse in Noise On-line Monitoring, Connect to Noise Screen
-
Product
NIBP Simulator for Testing Patient Monitors
SECULIFE BP PRO
-
The SECULIFE | BPPRO is the high-end product from the new range of NIBP simulators and is distinguished by a great variety of functions. It includes functions such as NIBP, IBP, ECG, temperature, arrhythmia, respiration, leak detection and much more. Specially developed to cover a great diversity of functions and nevertheless to ensure a compact design, the SECULIFE | BPPRO fulfills the requirements of modern medical technology. It makes no compromises with regard to functionality and input diversity. There's hardly another product with a similarly large range of features.
-
Product
Electrostatic Dust Monitor
201LP
-
The Redkoh Model 201LP is a three wire particulate monitor that measures particulate levels in air ducts on a real time basis. The Model 201LP is powered by an external 24V dc supply and its continuous 4-20 ma output can be connected directly to a PLC, recorder, or digital readout. Changes in the 4-20 ma output are directly related to changes in the concentration of particulate in the gas stream.
-
Product
H2O2 Monitor
HZ-960HPO-M
-
High stability measurement H2O2 concentration. The repeatability: FS +/- 0.2%. Can select 4 types of measurement range in-line detectors.
-
Product
Vibration Monitoring
-
Encore Electronics offers a full line of vibration monitoring equipment, ranging from DIN-rail mounted accelerometer signal conditioners to complete multi-channel monitor / alarm cabinets. Most are equipped with a 4mA power source for IEPE (Integral Electronic Piezo-Electric) transducers.
-
Product
Gas Monitor
S5000
-
The General Monitors S5000 Gas Monitor is the ultimate gas detector for extreme environments needing to detect oxygen, toxic and combustible gases.
-
Product
Machine Condition Monitoring
-
Machine Condition Monitoring and Predictive MaintenanceSpace-grade measurement technology brought into machine condition-based monitoring. Accurate, highly reliable, easy to use and cost-effective real-time condition monitoring solution. Our condition-based monitoring solution is ideal for any kind of rotating machinery such as electric motors, gearboxes, pumps, etc.
