Analog Input
measurable voltage value.received from a sensor.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 16 Channel
43-765-001
Analog Output Module
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
NI-9208, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module
780968-02
Current Input Module
500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The NI‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The NI‑9208 uses a standard D‑SUB connection for use with cables and connector blocks.
-
Product
sbRIO-9227, Non-Enclosed, 50 kS/s/ch, 5 Arms, 24-Bit, 4-Channel C Series Current Input Module
781118-01
Current Input Module
Non-Enclosed, 50 kS/s/ch, 5 Arms, 24-Bit, 4-Channel C Series Current Input Module - The sbRIO‑9227 was designed to provide high-accuracy measurements to meet the demands of data acquisition and control applications. It includes built-in anti-aliasing filters. When used with a C Series Voltage Input Module, the sbRIO‑9227 can measure power and energy consumption for applications such as appliance and electronic device test. You can not only measure and meter current and power but also look at quality factors such as noise, frequency, and harmonics. Non-enclosed modules are designed for OEM applications.
-
Product
PXI-6723, 13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module
778998-01
Analog Output Module
13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6723 delivers low-cost, high-density analog outputs to meet a wide range of applications, such as stimulus-response, signal simulation, waveform generation, and actuator stimulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6723 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-01
Counter Input Module
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
Product
REM-11120, 4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O
784750-01
Temperature Input Module
4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O - The REM‑11120 is a temperature input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11120 from a real-time controller such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM‑11120 also has an adjustable filter time for improved measurement quality and optional external cold junction compensation (CJC) or PT100 resistance temperature detector (RTD) measurements.
-
Product
NI-9201, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
779372-01
Voltage Input Module
±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected signals to the individual channels.
-
Product
sbRIO-9201, Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781114-01
Voltage Input Module
Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. In addition to the absolute protection from the isolation, the module features up to 100 V of overvoltage protection for errant signal connection or unexpected outputs to the individual channels. Non-enclosed modules are designed for OEM applications.
-
Product
Analog Oscilloscope
FS-404
-
*OSCILLOSCOPE: 40 MHz Dual Trace,Dual Trigger, 1mV Sensitivity, 10ns Resolution.*FUNCTION GENERATOR: 0.5Hz~5MHz Frequence, Sine,Square,Triangle,3 waveforms, Max output:20 Vp-p(No Load),10 Vp-p(50Ω? Load)., TTL Synchronous Output
-
Product
Analog DVR
-
Sylo Vision Technology Co., Limited
Security cameras capture an analog video signal and transfer that signal over coax cable to the Digital Video Recorder (DVR). Each camera may be powered by plugging in the power supply right at the camera or by using RG59 Siamese cable which bundles the video and the power cables. The DVR converts the analog signal to digital, compresses it, and then stores it on a hard drive for later retrieval. Intelligence is built into the DVR to handle such things as scheduling, motion detection, and digital zoom. Monitors for viewing the video are connected to the DVR, or it can be set up to publish over an internal network for viewing on PCs. The DVR can also be set up to broadcast over the Internet and can add password protection and other features. When broadcasting over the Internet, the video for all of the cameras is transmitted as one stream (one IP address). Therefore, it is very efficient.
-
-
Product
Analog Meter
-
Basic functions:DC current: 2.5/25/500mADC voltage: 2.5/10/50/250/1000VAC voltage: 10/50/250/1000VResistor: R x 1/R x 10/R x 100/R x 1000Special functions:Continuity buzzerLow battery displayMulti-protective circuitGeneral characteristics:Color: yellowNet weight: approximately 130gWindows size: 75x57mmSize: 123x84x34mmPower: 2 x 1.5V, 5#Packing contents:360Trx analog meterPacking cartonEnglish manualTest leadPacking:Carton size: 440x355x275mm
-
Product
Analog Oscilloscope
PS-205
-
*20MHz Dull Trace, Dual Trigger*Built-In Component Tesfer*X-Y Operation, Z-Mod Input, Y-Output*Beam-Finder, Hold-Off, Illuminate*With Delay Sweep*Two Sweep Mix Function
-
Product
NI-9216, 8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
783863-01
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9216 is a resistance temperature detector (RTD) input module. You can configure the NI‑9216 for two sample rate modes: high sample rate or high resolution. The NI‑9216 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3-‑or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9216 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
-
Product
Input Devices
-
Panasonic Automotive & Industrial Systems Europe GmbH
Panasonic's Electromechanical Components are used to convert mechanical movement into electrical signals. These products, including switches, encoders, and potentiometers, are used in everyday devices at the point of user interaction.
-
Product
Ruggedized Field Deployable Tester
PUMA
-
- 18-slot PXI / 4-slot SCXI Chassis- 1.2 GHz Embedded Controller- 4-axis Motion Controller/Simulation- 8-port RS-232 Serial Module- 4-port RS-485 Serial Module- 48 bit Isolated Digital I/O- Reconfigurable multi-function I/O FPGA Module- 5 1/2 digit DMM- 200 MHz 2-channel Scope/Digitizer- Multi-function Data Acquisition (DAQ)- 8-channel Analog Input Module- 6-channel Analog Output Module- General Purpose Switching- RF suite (optional)
-
Product
16-bit, 400KHz, 4 Isolated Analog Differential Inputs, Simultaneous Sampling
APCI-3003
-
With the new fast A/D converter board APCI-3003, the user can achieve high data transfer rates by a simultaneous conversion of 4 channels at once. The board has 4 differential input channels. Each channel has its own A/D converter. The transfer rate can be set in a flexible way from 100 kHz for each channel, when 16 channels are set, to 400 kHz for each channel, when 4 channels are set. All 4 channels are optically separated from each other up to 500 V.
-
Product
PXI-6704, 16-Bit, 32-Channel, Static PXI Analog Output Module
777796-01
Analog Output Module
16-Bit, 32-Channel, Static PXI Analog Output Module—The PXI‑6704 is a static analog output device. You can use the PXI‑6704 to create software-timed voltage and current output applications. You can independently set the output voltage range on each channel. The PXI‑6704 also includes eight 5 V TTL/CMOS digital I/O lines.
-
Product
Analog Functions
-
Analog Devices designs amplifiers and linear products that deliver high performance and high value. We combine circuit design, manufacturing process innovation, and applications expertise to create products that simplify signal conditioning design.
-
-
Product
USB-TC01, 1-Channel Temperature Input Device
781314-01
Temperature Input Module
The USB‑TC01 is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take … temperature measurements with your PC. You can connect the USB‑TC01 to any USB port to use your PC as a display and monitor data in real time. The USB‑TC01 is compatible with J, K, R, S, T, N, E, and B thermocouples.
-
Product
NI-9207, 500 S/s, 16-Channel C Series Voltage and Current Input Module
781068-01
Current Input Module
500 S/s, 16-Channel C Series Voltage and Current Input Module - The NI‑9207 is a combination voltage and current input module designed with industrial systems in mind. It features eight current and eight voltage input channels, with built-in noise rejection.
-
Product
External Input Module
EIM-01
-
The EIM-01 external input module is used to safely isolate and input an external drive signal into the MAC-01, -02 or -03 AC Power Sources/Frequency Converters. The unit can accept various waveforms from laboratory or programmable oscillators or from a Titan MOS-01, -01A, -01B when used as a slave unit in multi-KVA systems. BNC input is completely isolated and floating with 1,500VAC breakdown and excellent common mode rejection. A recessed 8% gain adjustment control is also provided. The EIM-01 must be factory installed.
-
Product
Smart Analog to Digital
618/619
-
Supports thermocouples, RTD's, strain gauges, voltage in, 4-20mA, thermistors, and resistorsUp to 16 differential input channels plus sensor excitationEach channel is software programmable for sensor type, gain, low-pass filtering, scan rateAuto-calibration eliminates trimpotsLow power consumption
-
Product
Analog Multimeters
-
With easy to read, color-coded analog displays.They use a microammeter with a moving pointer to display readings.
-
Product
Digital-To-Analog Converter
DAC-200
-
Advanced Thermal Solutions, Inc.
The DAC-200 is a digital-to-analog converter designed to convert the output of the ATVS family of instruments to 0-5VDC. The device produces an output whereby the voltage is linearly proportional to both the air velocity and temperature for the ATVS product family, including the ATVS-Nxt, ATVS-2020, eATVS-4, eATVS-8, and iQ-200.
-
Product
Temperature Input Device
-
The Temperature Input Device is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take temperature measurements with your PC. You can connect the Temperature Input Device to any USB port to use your PC as a display and monitor data in real time. The device is compatible with J, K, R, S, T, N, E, and B thermocouples.The Temperature Input Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Analog RF Slot Downconverter: 1700-2100 MHz Input
Model 8111-004
-
The Bandit® Model 8111 provides a series of high-performance, stand-alone analog RF slot downconverter modules. Packaged in a small, shielded enclosure with connectors for easy integration into RF systems, the modules offer programmable gain, high dynamic range and a low noise figure.
-
Product
Complete Input Solutions
-
We can help your ideas to become reality. With extensive consultation and support, Hoffmann + Krippner can offer everything needed to design and produce your ideal input device, including beautiful designs, exact and reliable electronics, optimal mechanics, and software solutions. In cooperation with OKW (as a joint venture partner) and TES-Frontdesign (as part of the Hoffmann + Krippner Group), we can provide a wide array of beautifully-designed, cost-effective enclosures and corresponding components, including stainless steel or aluminum enclosures.
