Vibration Control
A hardware/software product that generates one or more analog drive signals that are applied to a customer's amplifier / shaker / test device for the purpose of creating a specified vibration environment at one or more points on a test device. (dataphysics.com)
See Also: Vibration Controllers, Vibration Test
-
Product
Automatic Power Control system
-
The Automatic Power Control system cuts the incoming power supply to a traction unit for short periods. This is required where power supplied from one part of a power distribution system in separated from another by a neutral section. Its fitment prevents damage to the power distribution system or the vehicle.
-
Product
Controllable, Programmable Linear DC Source
LAB / S
-
*Linear laboratory power supply*High quality DC sources with the lowest residual ripple*CV / CC mode with LED display*Protection against short circuit, overload and overtemperature*Optional IEEE 488, RS232, analog interfaces*3-phase input optional
-
Product
Advanced 8/4-axis Servo & Stepper Motion Controllers with Modular Design
PCIe-8158
Motion Controller
The PCIe-8158 delivers high-frequency pulse rates up to 6.55 MHz and hardware-controlled emergency stop, software security protection, card index switching, and simultaneous linear/ circular run, exceeding industrial cost/performance requirements. Compatible with Mitsubishi, Panasonic and Yaskawa servos and any pulse-train controlled servo and stepper drives, the PCIe-8158 allows complex moving patterns through multiple axes that move with linear and circular interpolations using continuous contouring. Applicable for a variety of linear and circular trajectories, the PCIe-8158 delivers the smoothest motion control for a wide range of manufacturing applications. Modularized configuration accommodates ADLINK extension boards for distributed I/O control and high-speed triggering functions.
-
Product
Noise & Vibration Measurement Systems
BK8600
-
Rotation can produce noise and extraneous vibration for any number of reasons and could cause wear, discomfort, or other problems. The BK8600 series of testers are specially designed to test for these.
-
Product
Mass Flow Controller for Low Flow
HFM-200 / HFC-202
-
The HFM-200/HFC-202 is Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers. Featuring reliability and stability, the 200 Series is chosen by OEM's for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.
-
Product
SAFE-T-GROUND - Ground Continuity Monitor / Control
TR-7
-
Model TR-7 Safe-T-Ground provides continuous monitoring of a truck's ground connection throughout loading operations. Static electricity is often brought in by tank trucks entering the loading area. The Safe-T-Ground Model TR-7 instantly stops loading operations if a tank truck loses its ground.
-
Product
Batch Controller (pulse input)
-
A low-cost controller for repetitive fill operations. The typical application utilizes a flow meter input and two built-in relays: a Prewarn relay slows down the pump near a preset to avoid overshoot and a Batch relay stops the pump at the preset.
-
Product
NAND Controller IP
ONFI
-
Arasan is the leading supplier of mobile storage IP and its products are used by most first tier memory suppliers. Arasan's deep experience with NAND flash memory interfaces and mobile storage standards began in 2001 when it joined the SD Association and shipped industry first SD card IP in 2003. Arasan is a current member of ONFI and JEDEC.
-
Product
Versatile quality control testing system
QuickSun® 550Ei
-
QuickSun 550Ei is a versatile testing system for qualifying of PV modules with dimensions up to 105 x 205 cm2. Basic set up includes a top class solar simulator which measures modules in sunny side up position enabling e.g. soiling simulations. Several additional measurement methods can be integrated to the same system including high resolution EL imaging with analysis software from one of the most recognized EL system suppliers. Also hot spot revealing IR images can be recorded by applying either forward or reverse bias current, and true nA scale leakage current measurements can be performed with sensitive enough instruments.
-
Product
Vibrating Wire Peripherals
-
Many Campbell Scientific vibrating-wire peripherals enable dataloggers to read vibrating-wire sensors (also known as vibrating-wire or vibrating-strip transducers). These sensors measure strain, load, pressure, and water level, and they output a frequency signal generated by a vibrating filament. Campbell Scientific also offers vibrating-wire dataloggers that read the sensors directly.
-
Product
2-CH Pulse-Train Motion Control EtherCAT Module
EPS-7002
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
Control Electronics
-
Data acquisition and control electronics for optical radiation sources and measurement systems including precision current and voltage supplies for LEDs and tungsten halogen lamps.
-
Product
Test-Stand Software for TD6 Controller for QMax ATE
TD6 TestStand Software
-
Qmax Test Technologies Pvt. Ltd.
The TD6 TestStand will enable the users to sequence and execute their own test programs. The user can browse his/her test program and add it to the TD6 TestStand component. The test program can either be in the form of DLL ( Dynamic Link Library ) or EXE ( Executable ). And, the user can add any number of steps. As of now, we will support only the .Net based test programs. Each and every individual assembly or exe added in the TestStand component will be considered as a single step. All such steps on the whole added in the TestStand component will be considered as 'Sequence'. The same is priced at Rs. 8,42,520.00 plus GST @18% extra. For further details, pls contact sales@qmaxtest.com
-
Product
Software - for controlling Cleverscope
-
Cleverscope Windows Application Software. Note we have added the Frequency Response Analyser (FRA) and Streaming capability to our Cleverscope application and so now it is available with all variants of our products, including units you have already bought. For power supply and power plane measurements you do need the isolated CS701 signal generator.We also now have the CS448 with four 1kV isolated channels with CMRR > 100 dB at 50 MHz.
-
Product
Vibration Analyzers & Data Collectors
-
Wireless Vibration Analyzers and Data Collectors are replacing analyzers all over the world. Their easy connectivity and fast data collection timings make them the most convenient solution for vibration analysis nowadays. Digivibe products are the Vibration Analyzers with the largest number of functions in the market. They integrate advanced functions for Vibration Analysis and Dynamic Balancing with new Triaxial Wireless technology making them more portable and versatile. Furthermore, their compatibility with current mobile devices make them very easy to use and ultra-portable. ¡Meet our improved functions for bearing and gearbox analysis!
-
Product
Ku Band Gain Control Amplifier
-
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
Product
Dry Contact Control Unit
ZET 7161
-
The ZET 7161 is a three-channel control dry contact unit.
-
Product
Motor Control Resistors
-
Although these types of motor and control system are in many cases being supplanted by AC variable speed drives, it remains the case that many new installations make use of traditional resistor-based motor control on grounds of cost, simplicity and reliability.
-
Product
Control Unit
MX 62 TP
-
Teledyne Gas & Flame Detection
Bringing together the latest data logger and alarm unit for gas and flame detection systems, the MX 62 TP features an innovative HMI interface specifically designed to facilitate user-controller interactions.This interaction is simplified by a large, fully interactive 10" (up to 15") high-definition colour touchscreen, allowing for clearer visualisation of critical gas detection data.
-
Product
Automated Marking Quality Control System
Angara
-
The machine vision system ASKKM "Angara" is designed to detect and reject defects in the marking of labels, excise stamps, boxes, vials, ampoules, bottles, etc., which have visual manifestations in the field of permanent or variable printing. It is installed on a conveyor or mounted in a labeling machine. Labels are checked before being applied to the product or marking on the package.
-
Product
CNC Controls
-
HEIDENHAIN offers a full range of CNC controls for all common types of milling and turning machines. From simple three-axis CNC machines to highly complex machining centers with up to 23 axes, HEIDENHAIN controls are always the right choice. They are practical, versatile, and high-performing, delivering convenient initial setup and productivity. Controls from HEIDENHAIN stand for exceptional performance and ease of use.
-
Product
XMC Display Control Card
XM61002
-
LinkedHope Intelligent Technologies Co.,Ltd.
XM61002 is an XMC display control card independently developed by Linghao Intelligent®. It is mainly targeted at high-performance embedded graphics image processing and GPU general computing processing (GPGPU) applications.
-
Product
Shaker Controllers
ZET 017-U Series
-
Shaker Controllers of ZET 017-U series are represented by a software and hardware complex solutions based on FFT spectrum analyzer ZET 017 with task-specific software ZETLAB VIBRO for the control of shock and vibration impact produced by electrodynamic shaker systems. The modular principle of the system structure allows to increase the number of measuring channels from 4 up to 24.
-
Product
Motion Control
-
Welcome to Thorlabs; below you will find links to our selection of Motion Control products, a subset of our entire line of photonics products. Thorlabs’ motion control products are separated into manual and motorized linear and rotation stages, multiaxis platforms, actuators, and controllers. The manual and motorized stages can frequently be configured into 1-, 2-, or 3-axis solutions. Since many of the stages are available in either manual or motorized versions, creating a custom system is easy. For nanopositioning applications like waveguide and fiber coupling, our line of multiaxis flexure stages are ideal. Both the motorized stages and the multiaxis platforms are supported by a complete line of controllers for the various motors and piezoelectric actuators. In addition, we support custom and OEM motion control applications with an extensive line of manual, motorized, and piezo actuators as well as threaded adjustment screws.
-
Product
Control and Monitoring of Machines
Millenium 3
-
Easy to program and to implement, it enables the control and monitoring of machines and automation installations with up to 50 I/O. It is positioned right at the heart of the Crouzet Automation range.
-
Product
Galvo-Resonant Scan Head and Controller
-
Our LSK-GR08(/M) Galvo-Resonant Scanner contains one resonant scan mirror and one galvo scan mirror that deflect an incident laser beam in X and Y, respectively. Identical to the galvo-resonant scanner used in our Bergamo® II multiphoton microscopes and complete Cerna®-based confocal systems, the 8 kHz resonant frequency of the resonant scan mirror enables much higher-speed scans than a galvo-galvo system. In our Bergamo system, the scanner can achieve 30 fps at 512 x 512 pixels image resolution.
-
Product
Human Vibration Monitor
HVM200
-
The HVM200 is a small rugged vibration meter with built in Wi-Fi that can be used to measure hand-arm, whole body and general vibration. It includes the metrics and frequency weightings needed to measure human vibration. This 3 channel meter meets the requirements of ISO 8041:2005 and it is designed to measure per ISO 2631-1, 2 & 5 and ISO 5349 in support of the American Conference of Governmental Industrial Hygienists (ACGIH) Threshold Limit Values (TLVs) and the directive 2002/44/EC. This makes the HVM200 an ideal choice for an instrument used to demonstrate compliance with human vibration requirements and regulations worldwide.
-
Product
Teaching-use Portable Vibration Tester
KD-9363-ED-4S2R
-
King Design Industrial Co., Ltd.
Vibration testing is applied to confirm the reliability and screen out of the non-performing products prior to ship out of the factory; and to assess the non-performing failure analysis;expecting to become high standard, high reliability products.
-
Product
Predictive Vibration Monitor Solutions
VMU
-
Vibration Monitor Units (VMUs) from Astronics employ proven vibration analysis to predict the failure of fans and other rotating equipment on passenger and cargo aircraft. Accurate prediction allows maintenance to intervene before a failure can occur, eliminating the resulting smoke or smoke smell event that can result in costly flight delays, diversions, emergency landings, or cancellations.
-
Product
Complete TAP Signal Isolation for Corelis Boundary-Scan Controllers
ScanTAP IsoPod
-
The Corelis ScanTAP IsoPod™ is an add-on accessory that provides a galvanic isolation barrier between the target system and the boundary-scan (JTAG) controller hardware. While the Corelis boundary-scan controllers are highly robust and reliable, the complete electrical isolation helps prevent damage to the controller from harsh electrical environments where over-voltage and over-current can damage components.This Corelis ScanTAP IsoPod was designed to add an additional layer of protection with minimal cost and effort. Open the box and plug it in; everything just works.
