Product

2-18GHz Digitising Receiver

DR068-M1

-

Teledyne Defence & Space

DR068-M1 - Teledyne Defence & Space

Teledyne Defence & Space (TDS) DR068-M1 Digitising Receiver combines a state of the art broadband frequency measurement receiver with a high dynamic range successive detection log video amplifier to realise a high probability of intercept receiver. Digital signal processing techniques are utitlised to derive pulse parameters which are packaged into a PDW and transferred via a low latency Gigabit Ethernet interface. The DR068-M1 enables new and existing systems to incorporate a wideband high POI pulse detection capability with minimal integrating effort.

Product

Attenuators And Pulse Limiters

-

Schwarzbeck Mess Elektronik

Schwarzbeck Mess Elektronik

A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.

Product

60 GHz Noise Figure Test Set

-

Noisecom

Noisecom

The Noisecom 60 GHz Noise Figure test set has 4 separate systems designed to perform Y-factor noise figure measurements using a high performance Spectrum Analyzer or a dedicated receiver. Each system contains a highly stable V-band noise source, isolator(s), optional waveguide to coaxial transitions and an optional pre-amplifier for use with a spectrum analyzer. The two standard calibration tables have ENR data points at 1 GHz intervals.* System ENR is measured before the DUT connector and at the final output stage allowing for pre-test calibration of the system.

Product

Antenna, Loop Sensor

EM-6873 | 20 Hz – 100 KHz

-

Electro-Metrics Corp.

EM-6873 | 20 Hz – 100 KHz - Electro-Metrics Corp.

The EM-6873 Loop Sensor Antenna uses passive circuits to transform magnetic field components between 20 Hz – 100 kHz to an equivalent open circuit two-terminal voltage on the receiving instrument. Use of the conversion Factor Chart, supplied with each antenna, will yield the strength of the magnetic induction field referenced to a uniform field. The loop is electrostatically shielded and therefore is sensitive only to the magnetic component (B-field) of the electromagnetic fields.

Product

2-Port RS/232/422/485 Async Serial Communications Adapter PMC

2901

-

Technobox, Inc.

2901 - Technobox, Inc.

The 2-port Async Communications Adapter is a costeffective solution for providing additional RS232/RS422/ RS485 based serial ports for a host processor. Using configuration switches on the PMC board, each port is independently set-up at either RS232 or RS422 levels. In the RS422 case, an additional option is provided to transmit data on the receive data line in an RS485 fashion.

Product

Gateway

CODA-4780

-

Hitron Americas Technologies Inc.

CODA-4780 - Hitron Americas Technologies Inc.

The CODA-4780 has the capability to receive 5Gbps based on 2 x OFDM + 32 QAM over its DOCSIS 3.1 interface. The integrated Wi-Fi 3×3 2.4 GHz 802.11n and 4×4 5 GHz 802.11ac Wave 2 dual band MU-MIMO Access Point significantly improves customer experience extending range and coverage with blazing speeds. For wired clients, the four Gigabit Ethernet ports offer ultra-fast connections. Its switchable upstream (5~85/5~204MHz) offers the possibility of flexible integration to existing networks.

Product

Vector Finders with InternalAttenuators

VF-145 LA AND VF-145 LMA

-

National RF, Inc

VF-145 LA AND VF-145 LMA - National RF, Inc

The VF-145 LA and LMA models are functionally the same as the VF-145 L and LM on both electrical performance and mechanical specifications. However, the LA and LMA models include an internal PIN diode attenuator that provides up to 12 dB of attenuation (measured at 150 MHz, attenuation decrease slightly as operating frequency increases) to the incoming radio signal. This attenuation occurs after the signal is received by the unit and phase shifted for processing, but before it is placed on the coax feedline to the receiver. In addition, the PIN diode utilized will absorb short burst of RF should transceivers be keyed accidentally by the user. This feature aids in very strong signal DF operations but will not totally guarantee against system overload under very strong RF emissions.

Product

Analog Receiver / RF Tuners

-

Mercury

Mercury

The Bandit™ family of analog receivers or RF tuners provide a series of high-performance, stand-alone RF downconverter modules. These products offer a low noise figure, programmable gain and a high dynamic range and ensure there are no gaps in the RF spectrum coverage.

Product

Attenuators

-

AC Photonics, Inc.

AC Photonics, Inc.

Optical attenuators reduce the intensity of  transmitted light uniformly across the spectrum. Applications include preventing too much light from overloading a receiver.

Product

Economical Type Self-heal Circle AGC Optical Receiver

HR8236, HR8253

-

Hangzhou Huatai Optic Tech. Co., Ltd.

HR8236, HR8253 - Hangzhou Huatai Optic Tech. Co., Ltd.

HR8236, HR8253 are economical type forward path AGC optical receivers. Their technical performance and index are the same as HR9236, HR9253, except without 20-segment output level indication and network management interface.

Product

AMIDA 2020XP Tester

-

Amida Technology, Inc.

Amida Technology, Inc.

AMIDA 2020XP CIS tester is the latest generation of CMOS image sensor-specific measuring instruments from Metatech. In addition to the original true and accurate measurement, the high-throughput mass production solution designed for the high-throughput inspection of image lens modules and camera lenses has been well received after nearly 20 years of mass production experience. First-class factories at home and abroad import production. AMIDA 2020XP CIS testing machine not only meets the customer's testing time and high output and accuracy requirements. Within the range of functional flexibility, users can customize their measurement requirements according to the definition of various sensors. AMIDA 2020XP CIS tester is a new generation of CMOS Image Sensor dedicated tester, which integrates DC open/short/leakage test, AC Pattern test and image test. It uses 180 Pin high-speed cable to connect to the test end

Product

Synchro/Resolver Boosters

-

North Atlantic Industries

North Atlantic Industries

NAI offers a variety of multi-channel Synchro/Resolver Boosters that accept Synchro/Resolver inputs, and they deliver isolated outputs capable of driving passive and active loads such as Control Transformers or Torque Receivers. These amplifiers can be used stand-alone or in conjunction with Digital-to-Synchro/Resolver Converters.