Controllers
direct and or manage action.
-
Product
PXI Controllers
Controller
PXI Controllers are either embedded or remote. Embedded controllers contain everything you need to run your PXI system without an external PC, while remote controllers let you control your PXI system from desktops, laptops, or server computers.
-
Product
Ka-Band Silicon 5G Quad Core IC
AWMF-0108
-
The AWMF-0108 is a highly integrated silicon quad core IC intended for 5G phased array applications. The device supports four Tx/Rx radiating elements, includes 5 bit phase and 5 bit gain control for analog RF beam steering, and operates in half duplex fashion to enable a single antenna to support both Tx and Rx operation. The device provides 26 dB gain and +9 dBm output power during transmit mode and 28 dB coherent gain, 5.0 dB NF, and -28 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, Tx power telemetry, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 48 lead 6x6 mm QFN for easy installation in planar phased array antennas.
-
Product
RF Switch
DSW9-8R0-18G-2035
-
RF Switch, DC~18000MHz, SP8T, Programmed Switch, SMA Female, RJ-45, RS-232, GPIB Control
-
Product
WISE-71xx/WISE-72xx Modbus TCP Controllers
-
WISE (Web Inside, Smart Engine) are Modbus TCP based Data Acquisition Controllers that allow for remote monitoring and logic control through a web interface. They can trigger outputs based on inputs, send email alarms and can show the status through a web page. WISE Data Acquisition Modules can be configured through a web page to implement IF-THEN-ELSE control logic with just a few clicks; no programming is required.
-
Product
PXI BRIC8 FIBO Matrix Dual 93x4 2pin brkout
40-592A-113
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
IGBT For Inverter
-
IGBT product series for inverter for UPS, motor control, solar power generation, and welding applications, recommended for 1 to 50 kHz frequencies, and guaranteed against short circuit.
-
Product
BACnet / Modbus
-
BACnet™ MS/TP and Modbus RTU communicating sensors provide an easy-to-install and cost-effective means to measure temperature and humidity anywhere on your network. They’re especially effective where there is limited controller inputs or the application is for monitoring only. All BACnet™ sensors are BTL Certified.
-
Product
UV Aging System
-
King Design Industrial Co., Ltd.
*Comply with IEC 61215, IEC 61646 UV Preconditioning Test Specification *Radiation intensity is linear adjustable; the intensity deviation is guaranteed within ±15% on the testing surface *Test cabinet is equipped with timer controller in a time range of 0～9999 hr, as well as time accumulating and power-shutdown data-saving ability * Using the standard PT-100 membrane thermo-transmitter to accurately control temperature in testing process
-
Product
PXI Power Supply 1 Channel 40W 48V 2A
PS48401
Power Supply
The PS48401 is a programmable DC power supply in a 2-slot PXI/cPCI form factor. It features a fully isolated output capable of delivering 0-48VDC / 2A / 40W. It offers a programmable current limit and the ability to measure the output voltage and current under software or trigger control.
-
Product
Total Sulfur Process Analyzer
NEX XT
-
Applied Rigaku Technologies, Inc
Featuring third-generation X-ray transmission technology, the NEX XT represents the next evolution of process gauge for sulfur measurement (0.02% to 6% S) of crude, bunker fuel, fuel oils, and other highly viscous hydrocarbons, including residuums.The Rigaku NEX XT system is faster, more sensitive and far more compact than competitive systems, and provides continuous, reliable detection of sulfur at pressures up to 1480 psig. Rigaku NEX XT can operate as a stand-alone analyzer or provide real-time closed-loop control when tied into a blending or plant-wide automation system. Among its other key features are a simplified user interface, reduced standards requirement, automatic density compensation, password protection, and standard platform for communicating sulfur and density to a plant-wide DCS. Due to its unique design and robust construction, sample conditioning and recovery systems are typically not required.
-
Product
Countermeasures Amplifier
CMA-100
-
CMA-100 Countermeasures Amplifier is a high gain audio amplifier used to detect and identify certain types of surveillance devices attached to building wiring such as telephone wiring, LAN and server systems, AC power, and alarm wire. The CMA-100 Countermeasures Amplifier functions employ a sophisticated automatic gain control circuit that is superior to most audio amplifiers.
-
Product
Highly Precise Digital Manometer
LEX 1
-
KELLER AG für Druckmesstechnik
LEX 1 is a micro-processor controlled, accurate and versatile digital pressure measuring instrument with integrated Max.-/Min.-function for calibration and testing purposes.
-
Product
Moisture Meters
-
Precision Mastech Enterprises Co.
A handheld tool that measures the water content in materials like wood, drywall, concrete, and soil, typically as a percentage, to help detect hidden leaks, prevent mold, and ensure proper drying for quality control in construction, woodworking, and other industries.
-
Product
8-Ch SPST 20A-250VAC High Current
YAV90087
Relay
8 power relays Switching 20A 250Vac PNP Outputs para control or YAV90304 control CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
Power Quality
-
Schweitzer Engineering Laboratories, Inc.
SEL power quality controls increase power efficiency and reliability by improving a system’s power factor and voltage stability.
-
Product
SIGNAL & POWER ISOLATOR
EE301-ISOL
-
The EE301-ISOLATOR will completely isolate your electronic loads inputs & outputs signals plus ground returns from the main power input UUT (unit under test)... The module allows you to control the electronic load just as you would with any standard control signal. Input / Output & Power signals are fully isolated up to 350 VDC.
-
Product
New Link system Control and Image Capture Software
-
New uncluttered and intuitive user interfaceLive display of current status for easy monitoringFull control of heating and cooling rate, limit and hold time of up to 100 rampsRow by Row control of Vacuum, Humidity, Tensile Force and Shear modes controllable and synchronised with TemperatureParameters of connected Linkam sensors displayed and stored - e.g. Vacuum, Humidity, Force, XY position and Pressure (dependent on connected stage type)Real Time chart of temperature and other measured parametersTrigger I/O for synchronisation with other equipmentTriggers recorded and plotted row by rowAutomatic setup of controls and parameter limits based on stage type connectedFull five point temperature calibrationUSB 2.0 to T96 and CSS450 ControllersOptional modules including Linkam Imaging Systems with high performance camerasIncludes .NET Components for easy integration into 3rd party applications e.g. LabViewNative 64 bit application
-
Product
Remote Monitor Management Information Base
SNMP RMON MIB
-
For every control table in the MIB, create and delete rows with various combinations of SNMP requests (all variables in a single request throughall variables in individual requests).Determine which row of this table is modeling the ethernet interface connected to the agent (requires that we are using ethernet). Check that this is for the same interface discovered in the "interfaces" test. Check counters.Build a history control row pointing to the interface connected to the agent. Check validity and traffic reported.Test agent's ability to generate an alarm on an RMON variable, then on threshold condition. Test for support of alarms on failing events, and in the event of target variable vanishing.Set up agent to track hosts on the ethernet interface connected to the agent. Check that entry was added for Rmon device's own ethernet address.Generate various top N reports (hostTopN test) and check validity.Start a matrix capture and check that the src-dst and dst-src tables are in sync.Check a channel and check for event generation (filter test).Create a channel and start a capture. Test locking and wrapWhenFull operation.
-
Product
IC-3173, 2.20 GHz Intel Core i7 Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller
784227-01
Controller
The IC‑3173 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in extreme environments. The IC‑3173 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.
-
Product
Alternator Tester
ALTALYZER Tester
-
The Altalyzer tester is used to check the correct operation of alternators equipped with electronically controlled voltage regulators. In alternators of this type, the charging voltage is not constant, but varies depending on external factors such as: engine revolutions, number of current receivers, etc. The voltage at a given moment is determined by the motor controller by sending the appropriate information to the alternator.
-
Product
AC Test Transformer Products
-
Shanghai Guantu Technology Co., Ltd.
Manufacturing scope:Output voltage: 0~200kVOutput capacity: 0~20kVATechnical features of AC test transformer:Light weight; adopting oil-filled and air-filled structures reduces weight by 20% year-on-yearStatic noise; uniform electric field design and special fastening structure, no discharge and no mechanical noise at rated outputHorizontal iron core structure reduces the center of gravity of the equipment to a low pointMulti-flange combination with high structural strengthKey parts are cushioned with advanced elastic materialThe control box has complete protection functions and strong overload capacity
-
Product
150W Electronic Load
EL63150B
-
Features:*Number operation and control*LED display with high definition and high contrast, rich display information*Easy operation of knob encoder switch*Basic load function: constant current, voltage, power and resistance*Multi units used to multiple load ability*Short-circuit test*Battery test*Dynamic test*Multi parameters measured in the list*Remote voltage measurement*Panel and exterior trigger function*Protection function: over-voltage, over-current, over-power, over-heat, polarity connection in reverse*10 sets of parameters memorized and loaded, and automatically loaded on turning on the instrument*Intelligent fan control*Key lock and knob lock functions
-
Product
Trace Level Portable Gas Calibrator
Model T750U
-
Teledyne Advanced Pollution Instrumentation
The Model T750U is a portable, microprocessor based calibrator for precision trace-level gas analyzers. Using highly accurate mass flow controllers combined with compressed sources of standard gases, calibration standards are provided for multipoint span and zero calibrations. The T750U is housed in a high-density, molded travel case which includes an integral handle and wheels for durability and ease of use in the field.
-
Product
Remote Controller
Remote Control Interface
ADLINK Bus expansion is a technology that increases the number of slots of the same or different bus type for a host computer system. ADLINK bus expansion product provides variety of interface options, including PCI, PCI Express, PXI, and ExpressCard to increase bus slots and leverage the latest computing power of both desktop and server-grade computers for a variety of applications. The interoperability of different bus interface devices, such PCI, PXI and PCI Express, is also a great benefit for those facing complicated system integration tasks. ADLINK bus expansion products also provide complete hardware and software transparency, without the need for additional drivers or software.
-
Product
Reconfigurable Automatic Tester
-
Quick-Start Reconfigurable Automatic TesterCompact, Efficient Desktop Tester with Customer-Configurable PXI/PXIe Insert PXI/PXIe Insert – 8 Slots: 1 Controller, 7 Customer-Configurable PXI/PXIe Slots.
-
Product
CameraLink module
CAML-MOD3
-
Curtiss-Wright Defense Solutions
Even for simple applications, getting data into an FPGA structure can be critical. CAML-MOD3 simplifies CameraLink interfaces through a simple adaptor directly into and under control of a host FPGA, such as an XMC-FPGA05D.
-
Product
Thermal Conductivity Transmitter
Model 2000XTC
-
Teledyne Analytical Instruments
The Model 2000XTC Transmitter resets the standard for thermal conductivity detector based applications with the process control industry. As an intrinsically safe transmitter, packaged within a rugged, weatherproof housing, the 2000XTC is suitable for use in harsh, hazardous outdoor environments. Using a novel, solid-state thermal conductivity sensor, this cost effective transmitter can be configured to detect H2, He, N2 Ar, CO2 a number of other gases of or a number of other gases of interest in binary or multi-component interest in binary or multi-component sample gas mixtures.
-
Product
Electronic Speed Controller
AFI-ESC610
-
AFI-ESC610 is an Electronic Speed Controller designed to drive BLDC motors. It meets the industrial requirements of high voltage and high power motor application for electrical vehicles, airplanes, boats and medium duty industrial machinery. It is rated at 6KW.
-
Product
Engine Test Systems
Dynas3
-
Dynas3 Machines are specially suited for use in engine test stands. The AC machine, variable frequency drive with test stand controller and safety module are tuned to one another to form a system that has proven itself many times over. It can be used in any type of development and function test stand. The applications range from simple test stands for steady state operation up to sophisticated test stands for dynamic test cycles. Nearly every application in the field of engine testing can be performed on a test stand with DYNAS3.
-
Product
Wind Transmitters
-
Comptus wind speed and direction transmitters convert the sensor signals into electrical outputs suitable for connection to displays, computers, dataloggers, wireless transmitters, or other controls. Output options include: 0-1 mA, 0-1 V, 0--5 V or 4-20 mA. Power options include: 24 VAC, 120VAC, 230VAC, 12-24 VDC. Comptus transmitters come standard in a track mount for installation in existing enclosures. They are also available in NEMA rated enclosures. Please contact us for enclosure options.
