Charged Device Model
See Also: Model, Human Body Model
-
Product
Charge Meter
NK-1001A/NK-1002A
-
Probe-type charge meter that can easily measure the amount of discharge charge that causes static electricity destruction in the manufacturing, inspection, and assembly processes of electronic devices.Many ESD phenomena that impair electronic devices are represented by the CDM ( Device Charging Model). The CDM is a model that represents a phenomenon in which a high peak current flows at high speed when the device itself is charged and its external electrode is grounded. The coulomb meter measures the amount of discharge charge, which is the integral value of the current, with high accuracy.
-
Product
ESD & Latch-Up Test Service
-
MASER Engineering has automatic test equipment for the most common ESD test pulse models. MIL - JEDEC - ESDA - IEC standards. IC level Human Body Model. IC level Machine Model. IC level Charged Device Model. System level IEC 61000 HBM. AEC-Q100 Field Induced Gate Leakage test. Static Latch-Up test. Dynamic Latch-Up test.
-
Product
ESD Testing & Latch-Up Testing Services
-
EAG is an industry leader in ESD testing (Electrostatic Discharge) and Latch up testing. Our highly experienced engineering team use their industry leading knowledge and years or real world experience of the latest semiconductor technologies, circuit design, and device physics to optimize our customer's ESD and latch-up results. Human Body Model (HBM) and Machine Model (MM), Charged Device Model (CDM), Latch-up, Transmission Line Pulse (TLP).
-
Product
Transmission Line Pulse Testing
-
Transmission Line Pulse testing, or TLP testing, is a method for semiconductor characterization of Electrostatic Discharge (ESD) protection structures. In the Transmission Line Pulse test, high current pulses are applied to the pin under test (PUT) at successively higher levels through a coaxial cable of specified length. The applied pulses are of a current amplitude and duration representative of the Human Body Model (HBM) event (or a Charged Device Model – CDM – event in the case of Very Fast TLP, or VF-TLP).
-
Product
USRP Software Defined Radio Device
-
The USRP Software Defined Radio Device is a reconfigurable RF device that includes a combination of host-based processors, FPGAs, and RF front ends. The USRP Software Defined Radio Device include options that range from lower cost options with fixed FPGA personalities to high-end radios with a large, open FPGAs and wide instantaneous bandwidth. These devices can be used for applications such as multiple input, multiple output (MIMO) and LTE/WiFi testbeds, SIGINT, and radar systems.
-
Product
Dynamic Power Device Analyzer/Double Pulse Tester
PD1500A
-
As an off-the-shelf measurement solution, the PD1500A delivers reliable, repeatable measurements of wide-bandgap semiconductors. The platform ensures user safety and protection of the system’s measurement hardware.
-
Product
USRP-2954, 10 MHz to 6 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
783153-01
-
The USRP-2954 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and shorten time to results. You can prototype a range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding. The USRP-2954 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) reference clock. The GPS disciplining delivers improved frequency accuracy and synchronization capabilities.
-
Product
USRP-2920, 20 MHz Bandwidth, 50 MHz to 2.2 GHz USRP Software Defined Radio Device
781906-01
-
20 MHz Bandwidth, 50 MHz to 2.2 GHz USRP Software Defined Radio Device - The USRP‑2920 is a tunable RF transceiver with a high-speed analog‑to‑digital converter and digital‑to‑analog converter for streaming baseband I and Q signals to a host PC over 1 Gigabit Ethernet. You can also use the USRP‑2920 for the following applications: white space; broadcast FM; public safety; land-mobile, low-power unlicensed devices on industrial, scientific, and medical (ISM) bands; sensor networks; cell phone; amateur radio; or GPS.
-
Product
USRP-2955, 10 MHz to 6 GHz, 80 MHz Bandwidth, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
785264-01
-
The USRP-2955 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless receiver systems. It is designed for over-the-air signal acquisition and analysis. It features a two-stage superheterodyne architecture with four independent receiver channels and shares local oscillators for phase-coherent operation. It also offers a Kintex-7 FPGA programmable with the LabVIEW FPGA Module. With these features, the USRP-2955 has the RF and processing performance for applications such as spectrum monitoring, direction finding, signals intelligence, wideband recording, and radar prototyping. The USRP-2955 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock, which improves frequency accuracy and synchronization.
-
Product
USRP‑2930, 20 MHz Bandwidth, 50 MHz to 2.2 GHz, Included GPS-Disciplined OCXO, USRP Software Defined Radio Device
781910-01
-
20 MHz Bandwidth, 50 MHz to 2.2 GHz, Included GPS-Disciplined OCXO, USRP Software Defined Radio Device - The USRP‑2930 is a tunable RF transceiver with a high-speed analog‑to‑digital converter and digital‑to‑analog converter for streaming baseband I and Q signals to a host PC over 1 Gigabit Ethernet. It also features a GPS-disciplined oscillator (GPSDO) with PPS accuracy of ±50 ns. You also can use the NI USRP‑2930 for the following communications applications: white space; broadcast FM; public safety; land-mobile, low-power unlicensed devices on industrial, scientific, and medical (ISM) bands; sensor networks; cell phone; amateur radio; or GPS.
-
Product
Charge Amplifier
CH-1200A
-
CH-1200A is a high-performance charge amplifier to convert charge signal to voltage signal. Built-in integration function allows optimization of the signal which is input to the vibration data analyzer connected.Changing into a multi-channel amplifier is easy by connecting multiple units.
-
Product
Charge Converter
CH-6130/6140
-
The CH-6130/6140 charge converter is a simplified type of charge amplifier converting charge signal to voltage.It can be connected directly to an input BNC connector of a CCLD applicable equipment such as FFT analyzer or vibration comparator, enabling direct connection of a charge output pickup without suing a box type amplifier.
-
Product
Charge Integrator Amplifiers
AD8488
-
Analog Devices’ charge integrator amplifiers convert the charge acquired by X-ray or photodiode detectors to a voltage. The channels are composed of CMOS transistors, using typical high input impedance CMOS gates. The integrators generate charge dependent voltages using a range of selectable capacitance values that accommodate a broad range of input charge values. The integrators are followed by single-ended input to differential output voltage amplifiers where offset and low frequency noise voltages are subtracted from the input voltages.
-
Product
Charge Pumps
-
Renesas offers monolithic CMOS voltage conversion ICs that perform supply voltage conversions from positive to negative for an input range of 1.5V to 12V, resulting in complementary output voltages of -1.5V to -12V.
-
Product
Model Based Testing
RTT-MBT
-
Verified Systems International GMBH
The RT-Tester Model Based Test Case and Test Data Generator (RTT-MBT) supports model-based testing (MBT), that is, automated generation of test cases, test data, and test procedures from UML/SysML models. Moreover, it generates traceability data relating requirements, test cases, test procedures, and results.
-
-
-
Product
Charging Sets(AP)
-
The Parker Charging kit is an indispensable instrument for checking, adjusting or filling nitrogen into most of the hydraulic accumulators available on the market.
-
Product
Test Line • Devices for measuring electrostatic charges
-
HAUG offers a wide selection of easy-to-use gauges. These are field charges with which electrical charges, fields and potential can be measured. The measured values show how strongly a surface is covered with an electrostatic charge.
-
Product
System Modeling
-
Mentor Graphics SystemVision is a mixed-signal modeling and simulation environment using the power of VHDL-AMS and SPICE to verify your control and mechatronic systems. SystemVision includes graphical design entry, VHDL-AMS modeling and library tools, leading-edge simulation technology and powerful waveform viewing and analysis tools
-
Product
Accumulator Charging Kits - (Europe)
-
The Parker Charging kit is an indispensable instrument for checking, adjusting or filling nitrogen into most of the hydraulic accumulators available on the market.
-
-
Product
Auto Charging System Analyzer
TE6-0606
-
Hangzhou Tonny Electric & Tools Co., Ltd.
This unit simply plugs into your car's cigarette lighter socket and will present you with alternator and battery status. On the left side is the alternator status indicating if it's charging the battery at too high a voltage, normal or too low. On the right is the battery status green LED charged 12.4-12.6V, yellow LED recharge 11.8-12.35V, and red LED dead<11.75V indicators.
-
Product
NF-Series Standard Models
-
The E-DRIV® NF-Series standard models feature an adjustable RPM setting on the tool and a selectable Soft Start mode. Engineered for high volume manufacturing applications the brushless motor design ensures durability and reduces the standard maintenance costs associated with brush type electric screwdrivers. The NF power tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management assures product quality, cost savings and a reduction in overall ESD failures.
-
-
Product
Devices
-
Aegis Industrial Software Corp.
Eventually your MES system needs to interact with the physical world and that means hardware is necessary. Aegis offers pre-certified devices such as scanners as well as line control devices of its own design. The benefit for customers is a successful implementation that comes from Aegis' experience of 1600 installations dealing with thousands of identification challenges and process control challenges.
-
Product
Interference Modeling And Simulation
-
The CAST Navigation Jammers are designed to facilitate and support the testing, verification, and integration of single element Fixed Reception Pattern Antenna (FRPA) systems as well as multiple-element anti-jam antenna sub-systems such as Controlled Reception Pattern Antennas (CRPAs). These systems are an ideal solution for military and commercial laboratories where interference signal capability is required. CAST Jammer sub-systems provide precisely controlled signals for use in most types of GNSS testing applications, emulating interference conditions and threats that can occur in both urban and hostile environments.
-
Product
Model Vector Network Analyzer
DZV-1
-
Digital Signal Technology, Inc.
DZV-1 is the vector network analyzer which can be measured the impedance and VSWR of the antenna, S Parameter of RF component and devices. It is small and low-priced. So, it is suitable for the production line, laboratory use, various testing applications, and the educational use. The communication between the DZV-1 unit and PC is done via USB, which is also used for power supply. The LOG-MAG characteristic, the phase-characteristic, the group delay frequency characteristics, the Smith chart, the polar coordinates, the SWR characteristic can be displayed on PC.
-
Product
Wireless Devices
-
Schweitzer Engineering Laboratories, Inc.
Wireless devices use radio signals to communicate and pass data over the air, eliminating the need for traditional cabling.
-
Product
Location Devices
-
Flash Pinger is a small battery powered acoustic transmitter as well as an optical flashing recovery device. Multiple settings allow for selection of flashing, timing, and frequency options for use in a variety of different applications.
