Transmission
Measures the strength and integrity of a signal carried over wire, fiber or air.
See Also: Transmission Impairment
-
product
4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V
CPCI-7500
*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS
-
product
Rotating Dual Shaft Torque Sensors
RST SERIES
The RST- Series is our low range rotating torque sensors that are available in eleven full scale ranges of 10 through 30K inch pounds. The sensing element incorporates bonded foil strain gages of the highest quality along with coined silver slip ring and silver brushes for data transmission. The WR2, Flexural Natural Frequency, and Torsional Stiffness values as stated in the Dynamic Characteristics box below, are approximate and the tabulated data pertains to the torque pickup only, and does not include the effects of couplings or other rotating masses that would be part of a dynamic system.
-
product
Moisture Analyzer
5800
The 5800 is ideal for high-purity gas production, semiconductor gases, and the production, storage and transmission of olefins. It is suitable for use in industries including hydrocarbon processing, industrial gas and semiconductors.
-
product
Communications Module
CC02A
The CC02A Communications Card facilitates serial communications between each module in a Zero Two Series Flame and Gas Detection System and an external host computer, which allows fast access to operational and setup data registers. It supports a Burst Read feature that returns all registers of a module in a single transmission.
-
product
Universal, Dual Input, High Performance HART Temperature Transmitter
SEM310 MKII
The SEM310 is a universal programmable HART temperature transmitter which accepts most commonly used Pt100, thermocouple, mV and slide-wire sensors and generates an industry standard (4 to 20) mA transmission signal
-
product
ARINC-429 Multi-Channel Test & Simulation Module for Excalibur 8000 Family of Carrier Boards
M8K429
The M8K429 is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 8000 family of carrier boards. The module supports up to five ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word. The receivers allow for filtering and multi-storage modes of Data Words. The transmit channels operate via a transmit ‘instruction stack’ which allows scheduling of data transmissions and reduces the need for host computer intervention.The M8K429 comes complete with C-driver software library including the source code.
-
product
Impulse Current Test Systems
Fivestar HV Testing Equipment Co., Ltd.
Impulse current test systems are mainly used for testing transmission and distribution systems against the effects of direct or indirect lightning strokes or against electromagnetic interference effects. Primary application of impulse current test systems is the testing of surge arresters, nowadays mainly of the metal-oxide type (MOA) and surge protection devices (SPD). Now they are also widely used to test vehicles, aircrafts, and military applications.
-
product
Isolation Amplifier
Mornsun Guangzhou Science & Technology
An isolation amplifier is an amplifier that provides isolation between the input and output of the circuits, including isolation between their associated power supplies. MORNSUN offers different types of analog isolation amplifiers, such as acquisition type signal conditioning modules, output isolation signal conditioning modules, two-wire loop power supply signal conditioning modules and signal isolators, etc. These analog isolation amplifiers feature excellent temperature drift characteristics of less than 50PPM/℃ across the entire operating temperature range of -40 ℃ to +85 ℃ and achieve isolation transmission, signal conversion (programmable for some models), HART communication, signal amplification, port protection and other functions. SIP, DIP, SMD and DIN Rail packages are optional.
-
product
RF Switch
A microwave switch is a device to route high frequency signals through transmission paths.
-
product
Fiber Optic Tools
Shenzhen Sharingtek Communication Co., LTD
Are used to install, maintain, and test fiber optic cables, connectors, and networks. Fiber optic tools are essential for ensuring that fiber optic networks are installed and maintained correctly, so that they can provide reliable and high-speed data transmission.
-
product
Transmission
Since the beginning, we’ve partnered with international standards organizations to ensure our testing solutions not only adhere to the current standards but also to develop new standards. To this day, our instrument portfolio remains the only one in the world to cover full transmission measurements of all single-mode and multi-mode fiber types.
-
product
Value Series Industrial ATX Motherboard For 10th Gen Intel® Core™ I9/i7/i5/i3 Processors
IMB-C46H
The ADLINK IMB-C46H motherboard redefines efficiency, combining robust performance with cost-effectiveness. Designed specifically for industrial environments, this motherboard is built on the reliable H420E chipset, supporting 10th Generation Intel Core processors. It offers enhanced system stability and simplified integration, making it ideal for a variety of applications from warehousing and industrial automation to smart manufacturing. With features like PCIe 4.0 for faster data transmission, DDR4 memory support for optimal cost-performance balance, and comprehensive I/O capabilities including 2.5GbE LAN for superior connectivity, the IMB-C46H is tailored to meet the diverse needs of modern industries. Dive into a new era of industrial computing with the IMB-C46H, where performance meets affordability.
-
product
Cable Locator (LCD type)
5501 CB
Standard Electric Works Co., Ltd
● The 5501 CB transmitter is a great tool for locating and identifying cables and individual conductors● Locates both powered and unpowered cables ● Voltage measurement for cables: ACV 12V~450V DCV 12V~450V● Signal transmission • Transmission power level selection (includes 1, 2, 3) • Transmission signal code selection (includes F, E, H, d, L, C, O, A)● Flashlight & backlight function● Silent mode (disable button beep)● Level bar display on LCD screen (transmission power level indication)● Action wave display on LCD screen (when signal is transmitted)● Auto power-off function
-
product
Satellite Communications
Honeywell Aerospace Technologies
Our satellite communications solutions offer passengers and flight crew reliable voice, fax and high speed data communications throughout the world. Our multi-channel satellite communications systems offer 2 to 7 classic Inmarsat (Aero H, H+ and I) connection to the ground providing simultaneous, independent voice calls, faxes and/or modem transmissions worldwide. These systems provide first-call connection with the clarity and uninterrupted signal of a digital office telephone.
-
product
C-Band Single Channel Booster EDFA (SBA)
HSA4100 (With SNMP)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4100 series is a booster EDFA designed specifically for single wavelength optic transmission system. It is installed in the output end of optical transmitter, used for improving the output power of the optical transmitter, and extending the signal transmission distance.
-
product
Pogo Connectors
Battery and charging contacts are often also called pogo connectors or simply short travel probes due to their compactness and their short travel.They are particularly suitable as charging contacts and as interfaces for data transmission. But Pogo Connectors are also used in many end products where low-wear electrical contacts are required. Wherever quick-release electrical connections are needed, pogo connectors can be a clever solution. From charging rechargeable batteries, to applications in medical technology, all the way to use in the furniture and lighting industry.
-
product
Interceptor Metal Detector
Interceptor metal detectors are custom manufactured to achieve superior results in challenging applications. The Interceptor uses a simultaneous multi-frequency operation that effectively processes the transmission and reception of multiple frequencies continuously over a broad spectrum. This revolutionary operation facilitates an improvement in detection capabilities of up to 100% with stainless steel, especially when inspecting traditionally difficult “wet” products.
-
product
Gateway Inverse Function
InverTS
InverTS is ENENSYS’ DVB-T2 Gateway inverse function that de-encapsulates a T2-MI stream into one or several MPEG-2 Transport Streams over ASI and IP.The InverTS is designed to receive a single PLP or Multiple PLP T2-MI stream over ASI or IP in order to de-encapsulate the T2-MI stream into one or several MPEG-2 TS over ASI and IP. It outputs the MPEG-2 TS encapsulated by a DVB-T2 Gateway.The InverTS can also apply to a lot of use cases wherever applications require to retrieve the genuine and multiple MPEG-2 TS that are carried over the T2-MI stream. It can be operated for re-multiplexing a DVB-T2 stream with regular TS content or for simulcasting the same content over different networks.The InverTS is the ideal product to help monitoring a T2-MI stream either using its optional internal advanced monitoring tools or by connecting it to existing monitoring tools through ASI or IP. The Advanced monitoring option enables to supervise in real-time PLP bandwidth allocation, DVB-T2 transmission parameters and the MPEG-2 TS encapsulated within the T2-MI stream.
-
product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
Military Monitoring Systems
Antenna Technology Communications, Inc.
ATCi provides several products and services designed specifically for Military/ Government applications. Package offerings include our all inclusive Warrior Package, encrypted data, video and voice transmission solutions as well as mobile trucks and trailers that allow ubiquitous satellite and cellular field services.Call ATCi today for a Capabilities Presentation.
-
product
Laser Turbidity Meter
HU-200TB-EH
HU-200TB-EH is a laser-type turbidity meter that can measure turbidity of membrane filtered water, etc. with a resolution of 0.0001 degrees. A high-sensitivity turbidty meter with a minimum resolution of 0.0001 degrees at a measurement range of 0.0000 to 2.0000 degrees, which uses a long-lasting semiconductor laser as the light source and employs a transmission 90-degree scattering light method.This is best suited for sensitive measurement of turbidity on surface water.
-
product
Corrosion Inhibitor Evaluation
ASTM G202
Metals Samples provides solutions to study the performance of corrosion inhibitors in the laboratory. The Rotating Cage is helpful in selecting corrosion inhibitors for use in oil and gas production pipelines and facilities, transmission pipelines, as well as in oil refineries. It simulates aggressive field flow conditions that cause localized pitting corrosion in a simple laboratory setup. The precision, i.e., repeatability and reproducibility, of the rotating cage has been established (ASTM G202).
-
product
6U VPX Board
VP62003
LinkedHope Intelligent Technologies Co.,Ltd.
VP62003 is a 6U VPX board based on Intel® Xeon® D-15xx processors, with more than 7-year lifecycle. Supporting up to Intel® Xeon® D-1577 (16x 1.3GHz) processor, VP62003 is able to perform vector operation and floating point arithmetic that require high throughput. Besides, VP62003 supports Intel® Turbo Boost, with the processing speed of CPU up to 2.7GHz. The high-performance CPU and the Turbo Boost technology leave no worries for extra cost and complexity of system settings.VP62003 provides 4x Rapid I/O (SRIO) x4 for VPX Data Plane communication, 2x 8 PCIe for VPX Expansion Plane communication, 4x GbE for VPX Control Plane communication, and 2x 10Gb SFP+ in front I/O for remote data transmission and communication. Rich data exchange interfaces on VP62003 make it easy to build box-level or system-level solutions.
-
product
Plus Radio Ethernet Receiver
ACSRF-4040
The Plus Radio Ethernet receiver is required as part of the Tinytag Radio Data Logging System. It controls the transmission of data to and from the radio loggers: data received from the loggers is then sent to the computer for viewing with Tinytag Explorer radio software. If power to the computer running the system is lost, the receiver has a battery back-up which will maintain the mesh network until power is restored. This receiver plugs directly into a LAN removing the need for a computer in the area where monitoring is to take place. The receiver is powered using a plug-in Power over Ethernet adaptor (ACS-0041) which is supplied with the unit.
-
product
Industrial Ethernet Physical Layer Devices
The ADI Chronous™ Industrial Ethernet physical layer (PHYs) portfolio includes solutions for standard 10 Mbps, 100 Mbps, and 1 Gbps. It also features the new 10BASE-T1L technology for single-pair Ethernet.Our industry-leading low latency and low power PHY technology maximizes data transmission and signal integrity in deterministic applications by reducing cycle times and system power consumption. It enables superior synchronization of signals across the industrial network and supports the development of TSN.
-
product
Ethernet Tester
Shanghai Grandway Telecom Tech. Co., Ltd
Datacom tester including 2M Transmission Analyzer, TV Signal Tester, Cable & Antenna Analyzer, 1G(1000M) Ethernet Tester, 10G Ethernet Tester, etc.
-
product
GigE And 3x ASI Ports For PCIe
DTA-2160
DekTec's Gigabit Ethernet adapter with three ASI/SDI ports, allowing zero-jitter transmission and reception of Transport Streams over IP networks; the additional three ASI ports allow easy conversion between the two interface types.
-
product
LXI 2.4GHz 50ohm 8x4 Matrix
60-772-004
The 60-772 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 4 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
-
product
Vista Spectrophotometer
Hunter Associates Laboratory, Inc.
Determining the purity of raw materials ensures both safety and quality. Hunterlab’s Vista is the right instrumentation for quantifying the color range and meeting standards and regulations. Vista captures both visible-range transmission color, as well as haze with a single measurement, and exports data with ease in minutes.
-
product
Directional Source
BAS003
The BAS003 Source is designed to generate homogeneous sound fields using random noise in compliance with the following standards: Building acoustics (insertion loss, acoustic absorption area, etc: ISO 140-3, ASTM E90, ISO 140-5, ASTM E966). The BAS003 is typically used to generate a noise in a free-field for the evaluation of the transmission loss index of a façade. The available high-efficiency power amplifier, BAS002, is light and can be remotely controlled for easy use in the field.
