Light Fixture
-
Product
Mode-Conditioned Light Sources
-
Thorlabs' Mode-Conditioned Light Sources are fiber-coupled LED sources that have an output with a flat-top profile in the far field. Common applications include the testing of multimode fused fiber components as well as verification of modal behavior in fiber-based setups. Standard fiber-coupled LED sources can have a range of output profiles that are usually not uniform and vary from source to source. This can be dependent on emitter orientation, alignment with fiber tip, and connector assembly. These mode-conditioned sources have been engineered to distribute light evenly into all transverse modes, resulting in an equilibrium modal distribution at the output. The front panel includes an adjustment knob to control the power and an output port that accepts 2.2 mm wide-key FC/PC connectors. A DS15 15 V power supply with a location-specific plug is included with each device.
-
Product
Main Air Data Test Fixture for ADC's
TA-245
-
This is the Main Air Data Test Fixture as shown in the AZ-241 repair manuals and will allow by the book testing of the units.
-
Product
Noid Lights, IAC Test Lights & Ignition Spark Tester Kit
36330
-
Use to test electronic fuel injection signals, idle air control circuit and spark plug circuits. Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Includes 8 Noid Lights (for checking GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, BOSCH 2 and GM Multec 2; 2 IAC Test Lights (for straight and 90 applications); and Cat. No. 23900, In-line Ignition Spark Checker.
-
Product
Real Scene Lighting
LightSTUDIO
-
Image Engineering GmbH & Co. KG
Test charts are used to test digital cameras and to perform objective measurements. But there are certain aspects in testing a camera that require a real scene. One of these aspects is the correct white balancing for different types of illuminants. Another aspect might be the determination of the visual loss of detail due to noise reduction or the amount of noise in an image.
-
Product
Light Dependant Resistance Measurement Trainer
-
Unitech Scales And Measurements Pvt. Ltd
L.D.R. Trainer comprises of light dependent resistor (LDR) fitted to the shaft, which moves inside the tube where lamp is fitted at the other end. Variable DC voltage source is provided to vary the light intensity. Digital indicator is supplied to measure the light intensity in terms of distance moved between LDR and light source.
-
-
Product
Evaporative Light Scattering Detector
ELSD-LTII
-
The ELSD-LTII utilizes a high-efficiency LED and enhanced digital signal treatment to minimize noise and deliver optimum sensitivity for trace analysis. An innovative cell design also reduces band broadening and allows sensitivity levels below 200 picograms. The high-performance optical detection system can also be used for combinatorial chemistry and high-throughput screening applications. The new Low Temperature Evaporative Light Scattering Detector (ELSD-LTII) is an easy-to-operate, universal detector that identifies analytes with uniform sensitivity regardless of their spectroscopic properties. It is not a spectroscopic detector. Instead, it removes the mobile phase through evaporation and then makes a light scattering measurement of the dried analyte particles.
-
Product
Bench-top Optical Light Source
STC-BTOLS2201 series
-
Shanghai Stone Communication tech Co., Ltd
STC-BTOLS2201 series high stable Bench-top light source are microprocessor controlled laser diode sources which can support the variety of emitters such as: DFB,FP,PUMP,SLED etc. It is specially used in passive components testing, power meter calibration and general laboratory uses.
-
Product
LED Probe Clip Light
U1176A
-
Clip this 3-in flashlight on your test probes for great visibility when using your handheld DMMs in dark places
-
Product
MECHANICAL TEST FIXTURE KITS
TX-MT-SERIES
-
Test-X MT Series mechanical kits are an affordable solution to printed circuit board testing. With multiple configurations and available options, this product is sure to meet your testing needs. The MT Series features a hinged 3/8" FR4 probe plate, tooling holes for accurate drilling, and side handles for easy transportation.
-
Product
Module Type ASE Light Source
-
Module type ASE light sources are small in size and easy to integrate into equipments. The dimensions are different between models, and five sizes are available from the smallest MSA to S, M, M2 and L. All of them are operated on 5 VDC and the optical properties are the same as the corresponding bench-top models.
-
Product
Ambient Light Sensors
-
Renesas' ambient light sensors optimize display backlighting, enhance energy efficiency, and improve user experience with ultra-low light sensitivity, low power consumption, and precise spectral response. Our offerings include light-to-digital sensors with IR blocking filters and I2C interfaces, and light-to-analog solutions integrating photodiodes and amplifiers. Designed for automotive, industrial, and medical applications, these sensors deliver reliable performance even in demanding environments.
-
Product
Self-Powered Inductive Clamp Timing Light
130
-
The original battery powered timing light, built with quality to last. There is no need to connect to a 12 volt battery for power. This unit is powered by two “D” cell flashlight batteries. Great tool for marine, smowmobile, industrial, racing engines and other small engine timing. Don’t accept a copy.
-
Product
Light 0.75 (21.00) - 2.00 (57.00) Bead Probe
BTP-25HF-2
Bead Target Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Reading Lights
-
Our Carat® lights offer a wide range of fully customized reading light solutions crafted for your unique needs.
-
Product
SMD Test Fixture
16034G
Test Fixture
Perform impedance evaluation on a minimum SMD size of 0.6(L) x 0.3(W) [mm]
-
-
Product
Edge Connector Fixture
EDGE
-
An edge connector fixture can be a low cost alternative to a bed of nails fixture. The most important features of this Edge Connector Tester is its portablility, ease of use, intuitive control functions, and durability in a production environment.
-
Product
Light Logger Sesor
NUL-204
-
This sensor is very versatile with applications in many areas of the natural sciences. It can be used to study photosynthesis in biology, light-emitting chemical reactions in chemistry, the effect of changing voltage on a light-bulb's output in physics and more.
-
Product
3.4 MP Custom Lens Low Light Camera Module
e-CAM30_CUMI0330_MOD
-
e-CAM30_CUMI0330_MOD is a high performance, small form factor, 3.4 MP pluggable Low Light Camera Module with S-Mount lens holder. It is based on AR0330 - a 3.4MP CMOS Image sensor from ON Semiconductor®. It has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs the entire Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images, videos and the optional MJPEG compressions.
-
Product
ICT/FCT-Fixtures, Max UUT 370 × 300 mm (wxd)
CK-2 Medium (Hold Down Gate) / 230156
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
Light 0.83 (24.00) - 2.00 (57.00) Bead Probe
BTP-1HF-2
Bead Target Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Uniform Light Sources, Luminance Standards
-
Uniform light sources for the adjustment of pixels and intensity of image sensors and cameras as well as for the calibration of luminance and spectral radiance or in other words: Solutions for Imaging, Sensing & Remote Sensor Calibration.
-
Product
Lighting Reliability
-
LED/OLED package lifetime is highly dependent on thermal management, and LED lamp performance can be dependent on the luminaire in which it is installed. Lighting reliability test system for LED/OLED Products are widely used for normal /accelerated aging, lumen maintenance measuring, lifetime evaluation and temperature characteristic testing for LED/OLED products including LED package, array, module, OLED module and luminaires.
-
Product
Trailer Lighting System Tester
Scanner
-
A Scanner Trailer Lighting System Tester makes the job a lot faster and easier since it powers your trailer's lighting circuits in sequence. You check the operation of all lighting functions in a single walk-around instead of two or three.
-
Product
Uniform Light Sources - Unique And Specialist Configurations
-
We ware experts for custom integrating sphere light sources for specialist applications and for use in demanding environmental conditions. Please contact us with your specific request.
-
Product
Circuit Tester "Light and Sound" Hook Probe
TE6-0708C
-
Hangzhou Tonny Electric & Tools Co., Ltd.
*Tests 6/12 volt circuits with POWER ON.*Interchangeable tips allow tool to be used as a probe- or pierce-type tester.*Retains wire for perfect pierce with one hand.*Hook grabs hard-to-reach wires.*Durable insulated clip and heavy-duty cord for professional use.*Spring loaded strain relief prevents cord pull out and damage.*High intensity glow for under hood and under dash visibility.*Easy-to-hear buzzer provides quick circuit test confirmation.
-
-
Product
Universal Test Fixture
CAM/GATE
-
The Low Cost Solution for Accurate and Dependable Universal Functional TestThe CAM/GATE ® Universal Test Fixture System is your afforable, efficient solution for functional test. No need to have multiple fixtures in your test area...
-
Product
Light Source
UVF-204S
-
This is the ultra compact and light weight high power unit fully utilizing characteristics of the high stability and long life 200watt mercury xenon lamp.
