Protection Relay
acts as a circuit breaker in the event of a fault.
-
Product
PXI Single Microwave SPDT Relay 18GHz 50 SMA
40-780A-521
Relay
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
Product
Optical Protection System ( Single Fiber Two-Way )
OPS-1000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OPS-1000 Optics Protection System product series, mainly applies to optical communication field of single fiber two-way for main, light path switching equipment. It makes up from light path switching unit, optical power monitoring unit and network management terminal. In optical communication networks, OPS-1000 real-time monitor the optical power of operating fibers and spare fibers, when monitor the optical light path’s optical power is lower than setting switching threshold, it will alarming prompt and switch to the spare fiber to realize the line protection of optical transmission system.
-
Product
PCI Reed Relay Card, 32xSPST
50-115B-021
Reed Relay
The 50-115B-021 is a 32xSPST PCI general purpose switching card and is part of our 50-110B/50-115B range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
Transmission Protection
-
Schweitzer Engineering Laboratories, Inc.
SEL transmission protection solutions provide complete primary and backup protection from all types of faults. Using these devices helps you avoid expensive equipment damage and failure while maintaining system performance and increasing availability.
-
Product
General Purpose Reed Relays, Dry and Mercury Wetted
Series 89
-
Mercury wetted relays - 0.1 inch x 1.0 grid. As series 80 and 88 but with alternative pin configuration
-
Product
Switch Modules - 16 Single Pole, Form C, Discrete Relays which are Wired & Controlled Individually
JX16/KC
Switch Module
This module has 16 single pole, Form C, discrete relays which are wired and controlled individually. The relays can be externally wired to make any configuration needed. Use as individual A-B relays or use them to drive external relays, solinoids, or any external device. It is available with Type S or M reed relays.
-
Product
PXI High-Density Multiplexer: 64-ch, 2-Wire, 100Vrms/1A, Reed Relays
M9101A
Multiplexer Module
The M9101A, a high-density, 64-channel PXI multiplexer routes many different channels to a single point. The switches operate in a break-before-make mode that ensures no two points are connected at the same time or, if needed multiple channels can connect simultaneously. Ideal for routing multiple analog signals to a measurement device in automated test environment (ATE) or data acquisition systems. Each channel switches a high and a low for 2-wire switching up to 100Vrms, with up to 10W of power. Connection options include the durable connector block or the standard cable connections.
-
Product
Protective Cover, G18, ITA
410112541
Protective Cover
The ITA Protective cover is made of aluminum making it very rigid to protect your contacts and modules when the ITA is not in use.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 18 GHz, 50 Ω, SMA, External Termination, Failsafe, Remote Mount
42-781A-122-E
Relay
The 40-781A-122-E (PXI) and 42-781A-122-E (PXIe) are dual SPDT failsafe 18 GHz microwave relay modules with external terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
32-Ch Isolated Digital Input And 16-Ch PhotoMOS Relay USB 3.0 I/O Module
USB-5855
-
USB 3.0 SuperSpeedDaisy chainable by built in USB hub32-ch digital input and 16-ch PhotoMOS Relay output (Form A) isolationWide input voltage range (10 ~ 30 VDC)1500 VDC optical isolation for relay outputsQuick removable European type connectorLED indicators for I/O statusSupported operating systems: Windows 10/11
-
Product
Relay Test Jumper Kit
56810
-
Set includes four jumpers to fit the most popular size relays on domestic and import vehicles. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using green four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on. Set comes in blow-molded case for storage.
-
Product
Pressure Relief, Gauges, and Relays
-
Durable and accurate with factory and portable test kits for Rapid Pressure Rise devices.
-
Product
PXI Mixed Configuration Relay Module - 9 Cells Populated
40-138-AA-BB-CC-DD (9 CELL)
Relay
The 40-138 2A Relay Module with 9 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
PICO SIL Reed Relays
Series 111
-
Requires a board area of only 0.15 x 0.4 inches (3.8mm x 10.2mm). Pins on 0.1 inch pitch as 110 & 112. 3 Watts switch in Mu-metal or Plastic package (not illustrated).
-
Product
High Voltage Dry Reed Relays
Series 60 & 65
-
High voltage relays - chassis mounted, up to 15kV. Tungsten switches with power rating of 50 Watts maximum. Series 60 has solder terminals and nylon chassis mounting studs
-
Product
Solid State Relays
-
As well as being slim and thus saving panel space, The relays are very strong, have a large contact area and non-bendable pins. Connection to a PLC is easy and achieved faultlessly in a few seconds via click connectors. In addition, power switching in G3RV relays with DC outputs is managed by a MOSFET in the output, which has ideal heat dissipation characteristics.
-
Product
Electromechanical Relay Switches
-
SMA SPDT electro mechanical RF relay switch features Indicators, Failsafe, Normally Open with an isolation minimum of 60 dB. SPDT electromechanical relay radio frequency switch PE71S6052 is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. Our SPDT SMA coaxial RF relay electromechanical switch can ship worldwide the same day that it is bought as with our other available RF parts.
-
Product
80 Channel Relay Switch
DP-VXI-4503
-
DP-VXI-4503 is a 80 channel, one Form C (SPDT) relay switch designed as a C size VXI module. This high density switch module is designed with a register based interface occupying only one VXI slot. This module uses two Form ‘C’ relay switches. Out of the two contacts in each relay, one is used to provide the status of the relay through read back and the other is used for switching purpose.The user can write the command for the selected channels on to the primary latch of the FPGA section. Readback is available to confirm the selected commands. On command, the data from the primary latch is transferred to the secondary latch. The relay driver section provides the necessary drive to switch ON the relays. The buffers in this section drive the relay coils.This module features a back plane trigger for VXI triggered operation. On receipt of the back plane trigger the programmed relays will be energised/de-energised. Alternatively, software trigger can be used.
-
Product
Time-of-Flight 3D Camera with IP67 Protection Class, Sub-Millimeter Precision
LUCID Helios2
-
Time-of-flight camera with IP67 protection class;Dust and water resistant; HDRmodel available ! Sony DepthSense IMX556 CMOS sensor; Resolution 0.3 MP 640 x 480; Frequency: 30 frames / s; Price: $ 1,645.00.
-
Product
Optical Protection System ( Double Fiber Two-Way )
OPS-2000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OPS-2000 Optics Protection System product series, mainly applies to optical communication field of double fiber two-way for main, light path switching equipment. It makes up from light path switching unit, optical power monitoring unit and network management terminal. In optical communication networks, OPS-2000 real-time monitor the optical power of operating fibers and spare fibers, when monitor the optical light path's optical power is lower than setting switching threshold, it will alarming prompt and switch to the spare fiber to realize the line protection of optical transmission system.
-
Product
PCI Express 16 Reed Relay Output Digital Interface
8003e
-
The 8003e PCI Express digital I/O interface provides 16 Reed relay outputs. The outputs provide high quality, long-life, dry contact switch closures suitable for low-current applications up to 10VA. Reed relays are normally open and close when energized. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
Product
Diagnostic Relay Buddy 12/24
192
-
Relay Buddy 12/24 is a quick go / no-go tester for the most common automotive relays. This new version Relay Buddy tests both 12 and 24 volt relays. If the relay fails the test, 3 different trouble codes will advise you of the possible causes for the failed relay. The red LED will flash once, twice or three times to indicate the problem. Trouble code definitions are printed on the back of the tester for your convenience.
-
Product
Single-in-Line (SIL / SIP) Reed Relays From Pickering Electronics
Reed Relay
The SIL / SIP reed relay is the industry standard when high reliability and consistent performance are desired in a compact package. Pickering Electronics Series 100 - 110 SIL / SIP reed relays feature the highest quality instrumentation grade reed switches making them suitable for the most demanding application
-
Product
Protected & Intelligent Power Switches
-
Single/Dual high-side output with optimized protection function and analog current feedback for body, lighting and heater applications.
-
Product
Single-in-Line Reed Relays
Series 116
-
SIL relays - Smallest board area. 1A version requires 0.15 x 0.27 inches .(3.8mm x 6.8mm). 1 or 2 switches with 10 Watts rating. 5 or 12 Volt coils with optional diode
-
Product
Built-In Relay Self-Test Diagnostic Test Tool
BIRST
-
Verification and diagnosis of complex switching operation in a test system has always been an issue. BIRST (Built-In-Relay-Self-Test) diagnostic test tool provides a quick and simple way of finding relay failures available on some of our LXI and PXI switch matrices.
-
Product
Four Channel Relay Board for Power Supply Isolation
FXA-113 PSU Relay 4CH
Power Supply
The FXA-113 is a four-channel relay board designed as an output disconnect option for laboratory power supplies. Especially in ICT applications it’s important, that the power supply is completely isolated from the DUT during measurements. Therefor each channel features two high current relays for the power path and two reed relays for the sense path. All four channels are equipped with a status led and can be switched independently. In addition, it is delivered with an installed DIN rail carrier.
-
Product
Relay Tester
-
Beijing GFUVE Electronics Co.,Ltd.
Assists in the inspection, installation, and repair of assigned electro-mechanical controls and equipment systems.
-
Product
Radiant-Heat Protective Performance Tester (RPP)
-
Sataton Instruments Technology CO., Ltd
Radiant-heat protective performance tester which is normally called as RPP tester is to determine the radiant-heat protective performance of single or multi-layer textiles or other materials intended for heat protective clothes or assembly against radiant heat. The tester is a limited suitable tool for evaluating the potential of textiles for second degree skin burns.
-
Product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-33
Relay Matrix Module
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
