Bare Board Testers
check unloaded PCBs for opens, shorts, leakage and voltage breakdown.
See Also: Bare Board, Bare Board Test, Bare Board Probes, Bare board Fixtures, PCB
-
product
PC/104 Single Board Computer with Vortex86DX3 System-on-Chip
CM1-86DX3
The CoreModule CM1-86DX3 is a PC/104 board with DMP Vortex86-DX3 single chip solution and has a very good performance to power ratio. The board comprises all peripherals needed for an embedded PC on a small 3.775" by 4.050" printed circuit board. The CM1-86DX3 integrates a powerful yet efficient DMP Vortex86DX3 with graphic controller and audio controller together with an additional GBit Ethernet controller to form a complete PC, with all the standard peripherals already onboard. Two Ethernet ports (1x GBit and 1x 100MBit), four RS232/RS422/RS485 serial ports, two USB 2.0 host controller to handle the communication with external devices. There are PS/2 connectors for keyboard and mouse. A first generation SATA interface allows the connection of hard disk or CD drive. CFast is also available. System expansion can easily be realized over the PC/104 bus connectors.
-
product
13MP Jetson TX2/TX1 Camera Board
E-CAM130_CUTX1
e-CAM130_CUTX1 - 13MP Jetson TX2/TX1 camera board is a 4-lane MIPI CSI-2 camera solution for NVIDIA® Jetson TX2/TX1 developer kit. The e-CAM130_CUTX1 Board uses 13MP custom Lens camera module based on AR1820 CMOS Image sensor from ON Semiconductor. This camera daughter board can be directly interfaced to the NVIDIA® Jetson TX2/TX1 developer kit. The e-CAM130_CUTX1 is a 13MP color camera with the S-mount (also known as M12 board lens) lens holder.
-
product
CPU Boards and Modules
A key element for system development are flexible CPU boards. For this reason, esd electronics offers CPU boards and modules for a wide range of applications as standalone modules or plug-on boards with a comprehensive support of operating systems. All boards can also be customized according to customer requirements.
-
-
product
Dedicated Testers
Dedicated Testers are often inexpensive due to their low test point requirements, which allow for a reduction in switch cards, especially when compared with a Universal Tester. Ease of setup is accomplished through the utilization of transfer connectors between the fixture and the machine. However, this can contribute to a higher fixture cost than typically seen with a Universal Test Fixture due to the nature of their construction which is labor intensive.
-
product
DIP Tester
Model DS-10
Putting it a conveyor to flow through a solder bath to obtain information needed to manage it. The created temperature profile makes it possible to monitor the 50ms sampling temperature of the preheat and solder temperature sensors in addition to the conventional management items.
-
product
TIM Tester
The Analysis Tech TIM Tester 1300 is an automated test system for measurement of thermal impedance and conductivity on thin, thermally conductive materials of the type frequently used for electronic packaging, as well as a wide variety of flexible or rigid solids and semi-liquid or viscous materials. Generally, the TIM Tester 1300 can accommodate samples with high-to-medium thermal conductivity with contact pressures ranging from 10 to 550 psi (70-3800 kpa) and at sample temperature ranging from 15C to 70C.
-
product
High Frequency Clock Divider Board
Alliance Support Partners, Inc.
Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.
-
product
Configurable 6U OpenVPX Multifunction I/O Board
NAI offers a variety of 6U OpenVPX solutions, including rugged I/O Boards - designed to be combined with our smart function modules - to create a COTS-based, high-density, multifunction I/O solution for most sense and response requirements.
-
product
Surge/Impulse Testers
specifically designed to perform the Input Test on PV Panels in accordance with IEC 61730-2, Para. 10.5.3. The output is in accordance with the published waveform from 800-10000V peak (open circuit).
-
product
Vibration Testers
Application for vibration tester: used for measuring periodic motion, to check the imbalance and deflecting of moving machinery.Is pecifically designed for present measuring various mechanical vibration. So as to provide the data for the quality control, run time and equipment upkeep.use the high-performance acceleration meter, realize the repetitiveness and accurate measurement. it has the function of testing axle bearing situation
-
product
Burn-in Board Continuity Tester
CT-1
Burn-in Board Coninuity Tester. Verifies burn-in board continuity and component tolerances. 768 I/O channels, can be forced to the constant current source or grounded independently. Highly accurate measurement of resistance, voltage, and capacitance using a pair of precision instrumentation amplifiers.
-
product
Shelf Manager Carrier/Mezzanine Board fix-mounted for CompactPCI
064-754
Set of Shelf manager mezzanine board installed on the fix mounted carrier board. The fix mounted carrier board provides all interfaces via headers for easy access and can be used directly inside of your system platform.
-
product
Scorch Tester (Sublimation Fastness Tester)
TF415D
TESTEX Testing Equipment Systems Ltd.
Scorch Tester, to determine fabrics Ironing color fastness and sublimation color fastness, and dimensional stability under hot dry conditions. Sublimation Fastness Tester complies with ISO 105, BS 1006, AATCC 92/114/117/133. Sublimation machine price is reasonable.
-
product
Microhardness Tester
By adopting the Load-cell load system, multi-stage load switching is possible.
-
product
A PoE-PD I/O Board
AX93274
*PoE-PD I/O board complies with IEEE802.3at standard via an internal cable to power on SBC*100 x 32 mm*1 x LAN cable, 1 x power cable, 1 x thermal module*Compliant products: PICO831, PICO121, PICO841, PICO843
-
product
Continuity Tester
26200
Just clip lead to one end of wire in question. Probe other end of wire. If bulb lights up, there is continuity. If bulb fails to light the circuit is open. Not to be used on live circuits or computer sensor feed circuits.
-
-
product
Desktop Meter Qualification Board
2199
Providing complete capabilities for evaluating meters and communications performance, TESCO’s Desktop Meter Qualification Board (Catalog No. 2199) can generate any voltage and load conditions the meter may encounter in the field. Apply non-sinusoidal voltages with complex load waveforms. Perform disconnect tests and reconnect tests without having to worry about being able to drive the meter’s switches.
-
product
Data Acquisition I/O Boards
General Standards Corporation is a leading supplier in data acquisition I/O boards, provides a complete family of data acquisition cards for sonar, industrial, and embedded applications on several form factors/busses, and for many operating systems. Functions available include analog I/O, serial I/O, and high speed parallel I/O.
-
product
Rubber Testers
TA Instruments introduces a complete line of new instruments for the measurement of rheological and physical properties of polymers, rubber and rubber compounds at all stages of manufacture. The new rubber testing instruments include a Rubber Process Analyzer, Moving Die Rheometer, Mooney Viscometer, Automated Density Tester and Automated Hardness Tester.
-
product
Tachometer Tester
Maschinenbau Haldenwang GmbH & Co. KG.
for motorcycles, for cars and vans up to 4000 kg and for cars and trucks up to 13000 kg axle load.
-
product
BMP-1 Board Marker Probe
BMP-1
Current Rating (Amps): .05Voltage Rating (VDC): 15Recommended Duty Cycle: 1 sec. On (min.), 5 sec. OffTest Center (mil): 1,000Test Center (mm): 25.40Full Travel (mil): 62Full Travel (mm): 1.57Recommended Travel (mil): 50Recommended Travel (mm): 1.27Full Marker Travel (mil): 62Full Marker Travel (mm): 1.57Direction of Rotation: CCWScribed Diameter (mil): 50Scribed Diameter (mm): 1.27Rec. Mounting Hole Size (mil): 468Rec. Mounting Hole Size (mm): 11.89Recommended Drill Size: 15/32 (in) or 11.90 mm
-
product
Igniter Testers
Igniter Tester is a failsafe and portable digital ohmmeter specifically designed for ultra-safe resistance testing on squibs, flares, bridge-wire, and other explosive devices. The 620A-4 ohmmeter has been approved by the USAF Non-Nuclear Munitions Safety Board for usage on all non-nuclear munitions, and independently certified to meet Mil. Std. 810 Mtd. 511 for usage in fuel-filled environments. Due to its intense self-safety design and numerous certifications, the 620A-4 failsafe ohmmeter is the industry standard for military programs in need of igniter testing.
-
product
Battery Tester
BAT-500
Amprobe BAT-500 Battery Tester quickly and accurately tests batteries without taking the batteries off-line. This Battery Tester features a comparator function with pass/fail indication, and speed testing of batteries up to 500 Ah. Amprobe BAT-500 Battery Tester, compact and light weight, simultaneously measures battery resistance and voltage up to 40 V.
-
product
TDS Testers
Labodam TD testers are equipped with platinum sensors, providing fast and reliable measuring results. Easy to use and featuring a waterproof design, these instruments are protected against harsh conditions and can be used to measure total dissolved solid content present in drinking water, waste water, swimming pool, and aquarium water.
-
-
product
PXI Express Board Virtex-5 ADC Module
SMT791
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
product
Elmendorf Tear Tester
TESTEX Testing Equipment Systems Ltd.
Elmendorf Tear tester, a computer controlled falling-pendulum instrument, to decide the ballistic tearing strength of textiles, plastics, paper or board. Tear Strength Tester complies with ASTM D1424/5734, ISO 1974/9290, BS ISO 13937, etc. The tearing tester is further enhanced and supported by the easy to use computer. Elmendorf Tear Strength Tester will show its good performance when you do Elmendorf tear test.
-
product
Electrical Testers
Precision Mastech Enterprises Co.
AC Voltage range: 50V-1000V AC, 50/60HzSafety standards: Designed to international safety standard IEC61010 - 1/600V CAT III, 1000V CAT II.Battery: 2*1.5V (AAA type)Altitude: <2000mOperating temperature: -10 to 50CStorage temperature: -20 to 60CHumidity: <85% relative humidityDimensions: 157*24*20 mmWeight: Approximately 42g
