Bare Board Testers
check unloaded PCBs for opens, shorts, leakage and voltage breakdown.
See Also: Bare Board, Bare Board Test, Bare Board Probes, Bare board Fixtures, PCB
-
Product
RF Signal Testers
-
RF Signal Generators, Record & Playback Systems, Players, Productivity Tools and More
-
Product
Motor Stator Tester
DZ900
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical properties test of stators of y-type three-phase motors.
-
Product
Airborne Video Delay Board
MS 2006
-
- Spartan FPGA based Design- Customized design for delaying & switching video inputs to RF section- Interface with EW Signal Processor Unit- Two channel video inputs and control- Video Signal Delay from 1ns to 1ms- Over duty Indications- Inhibit Control- Discrete Interface
-
Product
Digital Output
VME-2170A
Digital Output Board
The VME-2170A optically coupled digital output board consists of VMEbus compatibility logic,data control logic, four 8-bit output registers, and 32 optically isolated high-level outputs. The board is implemented as a double Eurocard form factor PC board, and provides all necessary address decoding and data transfer control logic to accept both 8- and 16-bit data transfers. Optical couplers isolate the 32 outputs from each other and from the VMEbus.
-
Product
DMX Tester
DMXter 2U
-
Here's the DMXter 2U, a Lil'DMXter2 for bolted down applications. All the hardware and software features of the standard Lil'DMXter2 in a 2U 19" rack box, plus many new features.The user controls, the XLR connectors, and the LED illuminated LCD display are on the front panel. The 2U is equally at home as the back up controller in a theatre or TV studio, running a trade show booth, the background lighting for themed entertainment or as the built in test controller in a touring show DMX distribution rack. Its increased I/O capabilities will make it a useful addition to your test bench.
-
Product
Multifunction Installation Tester
COMBI519
-
COMBI519 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
-
Product
PC/104 OneBank Board
EMC2-SoM3-100
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-SoM3-100 to be added to robust and rugged installations for various commercial, medical, industrial and military uses and to enable more versatility the EMC²-SoM3-100 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
-
Product
CMP Tester
CP-6
-
The state of the art Rtec CMP tester CP-6 allows to study and characterize CMP process like never before. In addition to polishing wafers & substrates the tester comes with inline surface profilometer. This combinations sheds information on why and how the surface, friction, wear etc. changed. Tester also measures several inline parameters such as friction, surface roughness, wear volume etc. to understand the process in detail.
-
Product
Fiber Testers
-
Shenzhen Noyafa Electronic CO.,LTD
Provides a powerful combination of physical layer tools to troubleshoot copper/fiber links and LAN tools to identify and repair a wide range of network problems.
-
Product
Cable Transmission Tester
SIGNALTEK CT
-
If you install or maintain data cabling, SignalTEK CT allows you to generate PDF test reports that prove installed links run at Gigabit Ethernet transmission rates.
-
Product
Combination Board Tester
V250 / V250PXI
-
Qmax Test Technologies Pvt. Ltd.
V250 / V250PXI is designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
Product
In-Circuit Tester
Eagle MTS180
-
The Eagle offers low testing cost for high volume with even the most complex fixture applications. Equipped with a Press-Down-Unit and a combination of analog and hybrid In-Circuit test pins, the MTS180 is in a class for its own. Furthermore, the tester can be equipped with functional test modules to provide even higher fault coverage and thus satisfy the test requirements of a larger number of customers.
-
Product
Electrical Testers
-
UEi Test & Measurement Instruments
Devices designed to test the presence of, rather than measure, electrical conditions.
-
Product
Fabric Drape Tester
TF118
-
TESTEX Testing Equipment Systems Ltd.
Fabric Drape Tester, to measure and calculate the coefficient of drape by tracing a shadow of the draped fabric on paper. Fabric Drape Tester complies with BS EN 9073, BS 5058, ERT 90-1, etc.
-
Product
Antenna Position Tester
FTA
-
Fuzhou Fuguang Electronics Co., Ltd.
FTA series Antenna Position Tester is a convenient test instrument for planning, construction, maintenance and optimization of antenna system.
-
Product
DIGITAL EARTH TESTER
MTD-20KWe
-
The MTD-20KWe digital earth tester allows for the measurement of Earth Resistances and Soil Specific Resistivity, and also the spurious voltages caused by parasitic voltages present in the soil.
-
Product
Wrinkle Recovery Tester
TF112 AATCC
-
TESTEX Testing Equipment Systems Ltd.
AATCC Wrinkle Recovery Tester is used for determining a fabric's ability to recoverafter wrinkling under a pre-determined load for a set period of time.Provided with a set of 5x3 dimensional plastic replicas to grade fabrics 1-5.
-
Product
Performance Board
-
The role of the performance board is accurate transmission of tester signals all the way to the device leads. Custom performance boards from ADVANTEST deliver support for DUTs (devices under test), as they become faster and smaller, with greater pin counts, and increasingly take the form of SMDs. ADVANTEST performance boards also support a host of test requirements, such as analog test, high-speed performance, and high-density, for testing state-of-the-art ICs.
-
Product
Board Level Voltmeters
-
We've shipped more than half-a-million on-board controllers (OBCs) to manufacturers across the world. Our non-contact OBCs offer the accurate, drift-free, high-speed, and low noise measurements your applications require.
-
Product
P-GW Functional Tester
-
The LTE PGW Functional Tester provides a wrap-around test solution for the Packet Date Network Gateway by emulating all the LTE network elements surrounding the PDN-GW (System Under Test). The P-GW Functional Tester emulates LTE Core Network entities such as the S-GW, PCRF, OCS and OFCS. It tests the S5/S8, S7/Gx, Gy and Gz interfaces of the P-GW.
-
Product
Ground Bond Tester
260 Series
-
Our 260 Series makes Ground Bond testing simple. We offer two models so that you can have a simple and easy-to-use Ground Bond tester that provides the output current you need to satisfy NRTL specifications. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 260 Series can easily be deployed in both laboratory and production line environments.
-
Product
Video Compression Board
ICS-8580
-
The ICS-8580 is a standalone video frame capture, compression, streaming and archiving solution in an XMC format making it an ideal solution for demanding video streaming tasks in military and aerospace applications.
-
Product
Analogue IC Tester
SYSTEM 8 (AICT)
-
The SYSTEM 8 Analogue IC Tester is the answer to testing analogue devices. The key feature of the AICT is its ability to functionally test all common analogue ICs and discrete devices in circuit. It is also capable of testing all types of analogue and digital components by means of the well-known, power off V-I test technique. For users requiring only the latter function, please select the Analogue Test Station section.
-
Product
Distribution Transformer Tester
ADOC-3
-
The ADOC-3 is an equipment that has been designed to test distribution network transformers from 5 kVA to 3MVA.
-
Product
NBS Abrasion Tester
UI-FT40
-
NBS Abrasion Tester is used to test rubber abrasion resistance and to know material nbs abrasion index. NBS abrasion test is suitable for vulcanized rubber used for soles and heels of footwear. Unuo NBS Rubber Abrasion Tester is designed and applicable according to ASTM D1630. Here for More Abrasion Tester.
-
-
Product
High Voltage Testers
-
HV Test, which is also known as Hipot Test – short form of high potential – is used to test the insulation quality of the auxiliary circuit of circuit breakers. The HV Test is useful in finding damaged insulation, stray conductive materials around the conductors, and problems due to terminal spacing and tolerance errors in cables.
-
Product
Uniform Wear Tester
DRK546A
-
Shandong Drick Instruments Co., Ltd.
Instrument purpose: It is used to evaluate the abrasion resistance of stretchy knitwear.
