Solder Paste Inspection
assures volume and area of paste application.
See Also: Solder Paste, Solder Paste Measurement, 3D Solder Paste Inspection
-
Product
68-Pin SCSI Micro-D Female Solder Bucket
40-962-068-SB-F
-
This connector is designed to allow users to directly terminate with soldered connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Solder Test Pallet
WaveRIDER® NL 2
-
The wave soldering process is one of the most challenging procedures to set up. The ECD WaveRIDER NL 2 greatly simplifies wave solder set up and ensures perfect repeatability, time after time. Board recipe preheat temperatures, conveyor speed, wave height, contact times and parallelism are all measured and monitored using the WaveRIDER NL 2 process pallet.
-
Product
Post-Mould Inspection Machine
IV-P1000
-
The IV-P1000 is a post-mould inspection machine best known for being a fully automatic vision inspection station and for having a user-friendly GUI for operator and recipe setup. This machine is best used to inspect packages for surface defects on top and bottom.
-
Product
9-Pin D-Type Male, Solder Bucket, HV
92-960-009-M-HV
-
9-Pin Male D-Type Connector, High Voltage, Solder Bucket - Without Backshell
-
Product
Complete Non-Contact Inspection System For OLED/TFT/LTPS
GX3/GX7
-
*Fastest*Workable to large panel as well as fine pattern of medium-small panel*Workable to large mother glass of every generation*Possible to dock width Repair Machine
-
Product
Vacuum Inspection
INDEC
-
INDEC vacuum test systems monitor a wide range of containers during the production process, including bottles, jars and cans, by measuring the cap panel concavity of their closures which is dependent on the vacuum inside. This non-contact inspection reliably identifies defective containers for automatic rejection.
-
Product
Incremental Length Gauges For Measuring Stations And Multipoint Inspection Equipment
CERTO series
-
*Interferential scanning principle*Very high system accuracy of down to ±0.03 µm*Well-matched ball-bearing guide for very high quality*Defined thermal behavior*Large measuring ranges of up to 60 mm*Interface: 11 µAPP
-
Product
3D Automated Optical Inspection Systems (3D-AOI)
3Di Series
-
Saki’s 3Di Series applies cutting edge technologies to improve production efficiency and enhance production quality across the entire assembly line.
-
Product
Connector, 104-Pin D-Type Female, Solder Bucket, 5A, 4-40 UNC Screwlocks
C104DFR-2SB-1A
-
This 104-pin female D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied with rear cable entry backshell. This connector is suitable for use with Pickering modules that use the 104-pin D-type connector.
-
Product
Wireless Fiber Inspection Probe
OCI-20BN-W
-
OCI-20BN-W is a portable optical fiber connector inspector for checking fiber and connector end-face cleanliness, ideal for bench top and fiber optic network installation technicians to eliminate error caused by poor quality or improper cleaning.OCI-20BN-W offers excellent viewing on connector/fiber end-face and is able to feature to record and save image/video of fiber end-face; It can be connected to PC or phone by WIFI.More than 40 assorted high-precision tips designed for inspection solutionsAngled/Lengthened tips for awkward positions.Connect smart phone for testing FiberEye2 is the application on an android or IOS smart phone to capture, display and record the fiber end-face image from the Wi-Fi probe.Connect tablet/laptop for testing EFD is the analysis software on Windows tablet/laptop to have dusts, and scratches on end face inspected, analyzed, compiled and reported
-
Product
68-Pin Micro-D Male Solder Bucket With Backshell
40-962B-068-SB-M
-
This connector is designed to allow users to directly terminate with soldered connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Manual Spin Rotary Table for Optimal Circular Geometry (TIR) Inspection
TruMotion
-
Rotary Precision Instruments UK Ltd
Inspect circular components in a shop floor environment whilst maintaining world class accuracies more commonly seen in the standards laboratory.
-
Product
Fiber Inspection & Cleaning
-
ShinewayTech Fiber Inspection & Cleaning - Optical Connector Inspector, Wireless FIber Inspection Probe, Cleaning Pen, & more.
-
Product
On-site EL/PL Inspection Machine
“EPTiF”
-
"EPTiF (EL/PL Test in Field)" enables you to check invisible conditions of installed solar panels during daytime by EL and PL inspections, which are adopted by a number of solar panel manufacturers, without detaching solar panels. Irradiance-independent and steady results can be obtained. This is the first in the industry.
-
Product
25-Pin D-Type Male Solder Bucket
92-960-025-M
-
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
Building Inspection System with Moisture Hygrometer & MSX® IR Camera
FLIR MR277
-
The MR277 is the first FLIR building inspection system to combine the advantages of Infrared Guided Measurement (IGM) and our patented Multi-Spectral Dynamic Imaging (MSX) with advanced environmental sensors to help you quickly locate, clearly identify, and easily document problems. IGM technology and a laser pointer isolate the area where you can use the integrated pinless moisture sensor for non-invasive readings or external pin probe for invasive measurements. With automatically calculated environmental readings and a field-replaceable humidity/temperature sensor, the MR277 lets you finish the job and minimize downtime. Connect to external devices with METERLiNK® and use FLIR Tools® to enhance troubleshooting and reports.
-
Product
Pipe & Duct Inspection Cameras
-
Pipe & Duct Inspection Camera are video inspection cameras with a probe long enough (roughly 70 ft.) to locate and identify an obstruction in a water or sewer line or HVAC duct by taking close-up video clips and photos of it. The P16PIP probe (also available separately) that comes with the DPS16 Pipe & Duct Inspection Camera has better camera lighting and optics and slightly better resistance to water than the P610-20PR probe that attaches to a recording or non-recording wet/dry inspection camera console.
-
Product
Video Inspection Station
VIS300
-
Video Inspection Stations are available with?or without on-screen measurement capabilities?and offer?an excellent way to evaluate or test small works or items in?difficult to access locations.? As todays electronic and mechanical systems keep getting smaller, it becomes impossible to test or measure these products with traditional methods. For many applications, from development to production testing, video based inspection can help maintain quality control. Many of these systems are used in labs for development or used in production for testing production samples.
-
Product
Sensor for Filament Inspection
EyeFI
-
EVT presents the EyeFI - the sensor for the inspection of filaments. The sensor contains two cameras with an Aptina sensor and S-Mount lenses. The cameras are perpendicular to each other. It is therefore possible to inspect two sides of the filament, which means that the EyeFI can detect if the filament is out-of-roundness. Additionally the errors and defects can be detected. For example the occurring flaws are point-shaped or partly flaked, or point-shaped and transverse, or also looking like a longitudial rib, or only spots in different shapes. The defects can be detected with the EyeFI sensor. The EyeFI contains board cameras with sensors from Aptina, the IoCap and an evaluation processor. The housing is about 14x10x4 cm in size. The IoCap is the image-capture-IO-board, which is designed and developped by EVT.
-
Product
Bulkflow X-Ray Inspection System
-
Designed to be integrated into line with optional reject stations, the Bulkflow X-ray System is perfect for loose and free flowing products. Offering a good detection levels on a wide range of contaminants including all metal, bone, glass and dense plastics.
-
Product
96-Pin 1.27mm Pitch Female Solder Pad Connector With Backshell, Screwlocks
C096SFR-4SP-5A
-
This connector is designed to allow users to discrete wires using solder pad connections to the 96-Pin 1.27mm pitch connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Defect Inspection System
F30
-
The F30 System boasts a five-objective turret that enables the resolution-throughput flexibility required by today’s multi-process inspection applications. Equipped with an advanced productivity suite (waferless recipe creation, simultaneous FOUP, recipe server and tool matching), the F30 System redefines inspection cost of ownership expectations.
-
Product
Manual Spin Air Bearing Rotary Table for Optimal Circular Geometry Inspection
GeoInspec
-
Rotary Precision Instruments UK Ltd
Inspect circular components in a shop floor environment whilst maintaining world class accuracies more commonly seen in the standards laboratory.
-
Product
Packaged Food X-ray Inspection System
EPX100
-
Our revolutionary new x-ray system is so advanced it will not only improve your product safety and meet regulatory compliance but also will optimize and streamline your product inspection.
-
Product
*Micro-fluoroscopic X-ray Inspection System
Cath-X
-
The Cath-X is a bench top system employing Glenbrook’s micro-fluoroscopy technology providing highly detailed x-ray video of the critical components of the needle device. The transparent, safely shielded, view chamber permits the operator to locate the critical areas of the needle for inspection. The x-ray image can be further magnified using the electro-optical zoom feature of the Cath-X.
-
Product
Furnace and Electrical Inspection Camera
FLIR GF309
-
The FLIR GF309 is designed for high temperature industrial furnace applications. These infrared cameras are ideal for monitoring all types of furnaces, heaters, and boilers, particularly in the chemical, petrochemical, and utility industries. Custom-built to see through flames, the FLIR GF309 also features a detachable heat shield designed to reflect heat away from the camera and camera operator, providing increased protection.
-
Product
Wafer Inspection Products
-
Sonix provides manual and automated wafer inspection and metrology systems for wafers ranging from 100mm to 300mm, with extensive analysis capabilities at both the wafer and device level. These industry-leading automated wafer inspection systems are used by the world’s top manufacturers to ensure quality from development through production.
-
Product
Digital Automated Interferometer for Surface Inspection
DAISI
-
DAISI (Digital Automated Interferometer for Surface Inspection) achieves the high workability and repeatability with the features such as auto-focus function, auto-calibration function and auto connector fixing system.
-
Product
GoPxL Inspection Software
-
GoPxL® is our next generation software application for creating end-to-end, web-based inline measurement and inspection solutions deployed on Gocator® 3D Smart Sensors and Gocator® 2D Smart Cameras.
-
Product
X-ray Inspection System
X-eye SF160 Series
-
High-performance Micro-focus Open Tube with 160kV is installed and fine defects of 1㎛ are detectable. High-resolution X-ray image can be gained with world best magnification by installing high-price Open Tube as standard.Dual CT function can be purchased adtionally, and exact location & size of defects can be detected and analyzed with this function.
