VxWorks
-
product
TTEDevelopment System A664 For VxWorks 653
The TTEDevelopment System A664 supporting the ARINC 653 interface is an out-of-the box starter kit for integrating TTEthernet’s deterministic network technology with the time and space partitioned real-time operating system VxWorks 653. The easy-to-use and ready-to-run solution includes hardware and software as well as a Distributed IMA demo application showing deterministic communication among the different real-time operation system partitions. The system supports up to 1 Gbit/s speed, enables event-driven Ethernet (IEEE 802.3) as well as rate-constrained (ARINC 664 part 7) and hard real-time (Time-Triggered Ethernet SAE AS6802) communication on the same network with the option to synchronize IMA modules using the fault-tolerant TTEthernet network time base.
-
product
Interface
P-SER
P-SER I/O product is a native PMC form factor interface providing real-time serial input and output with high time-precision reception/input time-stamping, scheduled transmission/output, event triggering and interrupt support. This interface is designed to meet the needs of both the simulations/test and the real-time embedded applications whether in Windows or VxWorks environments.
-
product
Shared Memory Network XMC Interface
XMC-SMN
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
product
Dual Port Simulator Fiber Channel XMC Module
XMC-FC4 Simulyzer
*Two independent fiber channel ports*The two SFPs accept electrical as well as optical transceivers*Each port supports 1, 2, or 4 Gbps*Supports customer-specific defined transmission speed*Comprehensive decoding of FC-1, FC-2 and Upper Layer Protocol (ULP) frames*Triggering and filtering*Supports DMA for high-speed streaming*IRIG-B time code encoder / decoder for data correlation*Supports ULPs such as FC-AE-ASM, FC-AE-RDMA, FC-AE-1553 and FC-AV*Supports HS-1760E applications such as AS5653, AS5652 and AS5627*Optional fcXplorer, Windows-based FC simulation and analysis test software*FC SDK (Software Development Kit) provides drivers and APIs for Windows XP / 7,*Linux, VxWorks, QNX Neutrino RTOS and others on request
-
product
HS1760/MIL-STD-1760E Network Interface Controller for PCI Express
PCIe-1760-NIC-FP
Avionics Interface Technologies
Configuration Variants available: PCIe-HS1760-NCNT: One NC Node and One NT Node, PCIe-HS1760-NCNC: Two NC Nodes, PCIe-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data - 75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
product
Shared Memory Network PXI Express Instrument
PXIe-SMN
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - 3U PXI Express Module - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
product
Extreme Rugged PC/104-Plus, PCI-104 Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM3-BT4
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
product
Architecture T2080 Processor
VME-196
Curtiss-Wright Defense Solutions
Our VME-196 combines the performance and the advanced I/O capabilities of the NXP quad-core AltiVec enabled T2080 processor. The VME-196 is supported by Curtiss-Wright’s U-Boot, Green Hills INTEGRITY, Lynx Software Technologies LynxOS, Yocto NXP SDK-based Linux and Wind River VxWorks 6.9 and 7 Board Support Packages (BSPs) and driver suite.
-
product
ARINC 429 Test And Simulation PCIe Module
PCIe-C429
*4, 8, 16 or 32 software programmable TX / RX channels*X4 lane PCI Express host interface*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
ARINC 429 XMC Interface Module
XMC-429
Avionics Interface Technologies
16, 32, or 64 ARINC 429 channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable high/low speed operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - IRIG‐B time code encoder/decoder for data correlation - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - ANSI Application interfaces supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, and VxWorks (others provided upon request)
-
product
PXIe SSD Storage Unit
DM-4M.2-3U
The Big River™ DM-4M.2-3U PXI Express storage unit provides up to 3.8TB* of M.2 SSD storage capacity. With a PCIe x8 Gen3 host interface, the DM-4M.2 delivers high-speed data rates for sequential writes of 3.25GB/s** and sequential reads of 3.41GB/s** to PXI Express based systems. The single slot design of the DM-4M.2 increases the availability of valuable chassis space, allows for maximum storage flexibility. The DM-4M.2 complies with PCIe Gen3 protocol standards. The product is commonly used in the industrial control, test and measurement fields. The DM-4M.2 operates under Windows, Linux, Unix, Solaris and VxWorks.
-
product
3U Processor Board
CP39104
LinkedHope Intelligent Technologies Co.,Ltd.
Designed for industrial communication, CP39104 is a 3U CPCI serial card compliant with PICMG 2.0 R3.0 specification.CP39104 applies XR17D154 serial communication controller of EXER, and supports 4x RS232/RS422/ RS485. Therefore, CP39104 is highly suitable for testing and measuring in serial data communication applications.LinkedHope® provides CP39104 with a wealth of software drivers and BSP, including VxWorks, Linux, Windows, etc., to enable a wide range of application scenarios.
-
product
Embedded Services
Firmware Development (Boot/HAL/BSP), Device Driver Development (USB/PCIe/SATA), Diagnostic software Development, Application software Development, Algorithm Development, OS: RTOS, Linux, Android, VxWorks, Kernel Porting, Optimization, debugging and Benchmarking, Processors: ARM, 8051, ARC, Languages: Assembly, C, C++, Java, Scripting: Perl, Python, C Shell Scripting
-
product
Extreme Rugged PC/104 Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM1-BT1
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
product
6U Processor Board
CP62102
LinkedHope Intelligent Technologies Co.,Ltd.
CP62102, a product designed by LinkedHopeTM, is a 6U CPCI processor board based on Intel QM77/HM76 platforms supporting 3rd generation Intel i series CPU, up to 2.7GHz frequency, HD4000 integrated core graphics and dual-channel SO-DIMM memory (1333/1600) with up to 16GB DDR3 ECC (optional) and up to 64GB on-board SSD storage.CP62102 provides VGA and HDMI display and supports different display terminal output. CRT displays up to 2048x 1536. Besides CP62102 provides a wealth of software drivers (BSP) support, including Windows7, Windows Vista, Windows XP, WES 7, VxWorks, Linux, etc., as can reduce system integration workloads and end application development efforts, so to shorten time to market.
-
product
6U CPCI Processor Board
CP62101
LinkedHope Intelligent Technologies Co.,Ltd.
CP62101, a product designed by LinkedHopeTM, is a 6U CPCI processor board based on Intel QM67/HM65 platforms supporting 2nd generation Intel i series CPU, up to 2.5GHz frequency, HD3000/2000 integrated core graphics and dual-channel SO-DIMM memory (800 /1066 /1333) with up to 16GB DDR3 ECC (optional) and up to 64GB on-board SSD storage.CP62101 provides VGA and HDMI display and supports different display terminal output. CRT displays up to 2048 × 1536. Besides, CP62101 provides a wealth of software drivers (BSP) support, including Windows7, Windows Vista, Windows XP, WES 7, VxWorks, Linux, etc., as can reduce system integration workloads and end application development efforts, so to shorten time to market.
-
product
ARINC 429 Test And Simulation USB Module
USB-429
*4, 8 or 16 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
MIL-STD-1553 PMC Interface Module
PMC-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
MIL-STD-1553 XMC Interface Module
XMC-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurations - Transformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating availableDesigned for extended temperature operations - x1 Lane PCI Express Host Interface - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Software Development Kit
InterNav®
Open architecture software with interface source code and analysis tools for integrating GPS, inertial, and other aiding sensors on a VxWorks, Linux, or Windows computer.
-
product
Application Programming Interface Software
AltaAPI
Alta’s 1553 and ARINC cards include the most advanced Application Programming Interface (API) library tools in the avionics industry, AltaAPI. The API architecture is a properly OSI modeled development package that provides an extremely flexible design to provide quick porting to various operating systems (such as VxWorks 5.X/6.X/7/MILS, Integrity, LynxOS RTOS), Linux 32- and 64-bit, Solaris 10, LabVIEW and 32- and 64-bit Windows 7/8/8.1/10.
-
product
6U Compact PCI® Single Board Computer
CP62001
LinkedHope Intelligent Technologies Co.,Ltd.
CP62001 is a 6U CompactPCI® single board computer designed based on Intel® GM45 chipset, compliant with PICMG®CompactPCI® specifications. There are SATAII, USB2.0, 10/100/1000Mb Ethernet, and Keyboard/Mouse interfaces on board. The display controller integrated in CP62001supports VGA and DVI dual output independently, with up to 2048×1536 resolution on CRT. Up to 4GB soldered memory on CP62001, leaves no worry about the board stability under harsh shock and vibration environment for end users. Besides, LinkedHope™ provides variant drivers BSP) support, such as VxWorks, Linux and Windows, as reduces the workload of system integration and the development of final solutions and shorten the Time-to-Market.The CP62001 with high performance/power ratio, works stably in extended temperature range, and is an ideal selection for high reliability and high availability required applications, like harsh environment communication, network security, video/image processing and can also be an ideal control unit in variant devices and equipment.CP62001 has a ruggedized version (called CP62002)with conduction cooling and wedge-lock technology. CP62002 is designed for extremely harsh environment.
-
product
Shared Memory Network PCI & PCIx Interface
PCI-SMN
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Compatible with PCI & PCIx Host System Slots - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
product
HS1760/MIL-STD-1760E XMC Network Interface Controller
XMC-1760-NIC-FP
Avionics Interface Technologies
Configuration Variants available: XMC-HS1760-NCNT: One NC Node and One NT Node, XMC-HS1760-NCNC: Two NC Nodes, XMC-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
product
ARINC 429 PMC Interface Module
PMC-429
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx ChannelsProgrammable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application Interface supporting C++, C#, and .net DevelopmentDevice Driver Support: Windows, Linux, VxWorks, and other operating system - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
ARINC 429 Test And Simulation PCI Module
PCI-C429
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
Extreme Rugged PC/104-Plus Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM2-BT2
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PC104p-429
*4 or 8 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*128 MB RAM*Label selective triggering for recording / filtering*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
Extreme Rugged PCI-104 Single Board Computer with Intel® Atom™ Processor E3800 Series SOC
CM3-BT1
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
product
ARINC 429 Test And Simulation PMC Module
PMC-429
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
