CAT 6
Category 6 cable.
-
product
LXI Microwave Multiplexer, SP6T, 7-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-507
Our 60-800-507 is a 7 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI 4 Slot BRIC Solid State 192x8 1-Pole (6 sub-cards)
40-563A-021-192X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
ATCA 5U 6 Slot Mesh
109ATCA506-300XR
The 5U 6-slot ATCA backplane is a 3X Replicated Mesh, compliant to the PICMG 3.0 Rev 3.0 specification. Elma Bustronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
product
Audio Cable Testers
AudioJog Pro 5
ALL new Audio cable tester with SINGLE & DOUBLE ended testing. There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
product
Oscilloscope, 6 GHz, 80 GS/s, 8000 Mpts/ch, 4 Channel, 12-bits
WaveMaster 8060HD
Oscilloscope, 6 GHz, 80 GS/s, 8000 Mpts/ch, 4 Channel, 12-bits.
-
product
6-12V Heavy Duty Circuit Tester
1668
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems. To indicate whether there is an electrical potential at any low voltage point in the system. By using the pointed contact tip to pierce insulation on cables, it will also indicate if current is present. This can be helpful when tracing faults or add cable to a circuit.
-
product
6 GHz, 4 Channel Programmable Delay Line
QPADL6
The QPADL6 is a programmable delay line instrument with 4 independent channels designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 6 GHz.
-
product
6-48V Digital Circuit Tester
1674E
Peaceful Thriving Enterprise Co Ltd
Checks on 6, 12, 24 and 48V systems.
-
product
Near Field Probes 30 MHz - 6 GHz
XF Family
The XF family consists of 4 passive magnetic field probes and 3 passive E field probes designed for measuring magnetic and E-fields in ranges from 30 MHz to 6 GHz during the development phase. Due to their integrated impendance matching the probes are less sensitive in the lower frequency range than the RF type probes.
-
product
DC Bias Current Source
TH1778AS
Changzhou Tonghui Electronic Co., Ltd.
■ Test Frequency: 0Hz - 2MHz ■ Provide 0~20A of constant current output, and must be controlled by TH1778A ■ Support 6 machines on line at most and
-
product
Carbon Monoxide Detector, CO
ENVIROMUX-CMD
Continuous air monitoring. Pre-set alarm points alert at: 70 ppm after 60 to 240 minutes; 150 ppm after 10 to 50 minutes; and 400 ppm after 4 to 15 minutes. Flush or surface mount. Test functionality of electrochemical CO sensing cell. Connect to RJ45 or digital input sensor ports. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1000 ft (305m). LED indicators for operation status and system test. Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL.
-
product
Mini Receiver
FB7-NX
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
product
Infiniium MXR B-Series Oscilloscope: 6 GHz, 4 Channels
MXR604B
MXR604B Infiniium MXR B-Series, 6 GHz on all 4 channels, option to integrate up to 8 instruments in one, hardware accelerated plotting, and fully upgradeable...including up to 8 channels.
-
product
Optical Light Source
TM3111
TM3111 optical light source is a handheld optical light source, It can provide 1 to 6 wavelengths output to satisfy specific requirements including the 650nm visible light source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer’s needs.
-
product
Towing Dynamometer
RS-40K
RS-40K towing dynamometer is designed for testing today’s DOT Vehicles (Classes 5 and 6) which include trucks and buses. The RS-40K is built with a heavy-duty steel frame, industrial axle and rides on an air ride suspension. The RS-40K is designed to maintain 40,000 Newtons of constant drawbar force and the ability to simulate an uphill slope of 25%. The dyno uses eddy current absorbers with special high temperature coils. The power is provided by an industrial generator. Testing is unlimited at lowspeeds.
-
product
Front Panels for Plug-In-Units | ATCA
EMC front panel for ATCA plug-in-units | 8 U x 6 HP | classic or ergonomic
-
product
COM Express Type 6 evaluation carrier board
ATX-M-CC462-T6
The ATX-M-CC462-T6 is a fully featured COM Express Type 6 evaluation carrier board designed for use with the WINSYSTEMS Intel® Tiger Lake UP3 COM Express and other COM Express Type 6 modules.
-
product
Economy Mechanical Calibration Kit, DC To 6 GHz, Type-N, 50 Ohm
85032E
The Keysight 85032E economy calibration kit contains a type-N male fixed termination and a one-piece type-N male open/short circuit. These standards are used to calibrate Keysight network analyzers for measurement of devices with 50 ohm type-N connectors. The kit is specified from dc to 6 GHz.
-
product
Scienlab Battery Test System — Cell Level
SL1002A
Test System with up to 36 Channels.The Keysight SL1002A provides sink and source with 0 to 6 V, 100 to 600 A, 0.6 to 3.6 kW and 36 channels for battery cells.
-
product
COM Express Compact Size Type 6 Module with AMD Ryzen™ Embedded V2000 APU (Zen 2 architecture)
cExpress-AR
The cExpress-AR, featuring the new AMD Ryzen™ V2000 APU with its high performance integrated Radeon™ graphics, is the first Type 6 module on the market to support an octa-core (8-core) embedded SoC, with up to 16 threads and an impressive turbo boost up to 4.2 GHz. Compared to earlier embedded quad-core V1000 processors, the additional cores combined with AMD's Zen 2 architecture result in a more than two-fold performance increase and double the performance-per-watt efficiency.
-
product
PXIe-4300, 16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module
781337-01
16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module—The PXIe‑4300 provides integrated data acquisition and signal conditioning for high-voltage measurements. It provides increased accuracy, simultaneous sampling, and synchronization features for scalable measurement systems. The PXIe‑4300 includes 300 Vrms channel‑to‑channel CAT II isolation and 3,300 Vrms channel‑to‑earth 5 second withstand isolation to protect users and equipment from hazardous voltages. This module offers programmable lowpass filtering, DC input coupling, and two PFI lines for digital input triggering. The included NI‑DAQmx driver simplifies hardware and configuration and measurement.
-
product
USB-6216, Isolated 16 AI (16-Bit, 400 kS/s), 2 AO (250 kS/s), up to 32 DIO USB Multifunction I/O Device
780170-01
Isolated 16 AI (16-Bit, 400 kS/s), 2 AO (250 kS/s), up to 32 DIO USB Multifunction I/O Device - The USB‑6216 is an isolated, multifunction DAQ device. It offers analog I/O, digital I/O, and two 32‑bit counters. For improved accuracy and safety, the USB‑6216 provides 60 V, CAT I isolation. It also features signal streaming technology that gives you DMA-like bidirectional high-speed streaming of data across USB. The device is ideal for test, control, and design applications including portable data logging, field monitoring, embedded OEM, in-vehicle data acquisition, and academic. The USB‑6216 features a lightweight mechanical enclosure and is bus powered for easy portability. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
SMARC Short Size Module with Qualcomm® QRB5165 Series octa-core SoC
LEC-RB5
The ADLINK LEC-RB5 is a SMARC module powered by the Qualcomm® QRB5165 SoC with 8 Arm Cortex-A77 cores and up to 15 TOPS Qualcomm® Hexagon™ Tensor Accelerator. The module is designed for robotics and drone applications and integrates several IoT technologies in a single solution. The LEC-RB5 SMARC module provides on-device artificial intelligence (AI) capabilities, support for up to 6 cameras, and low power consumption. It is capable of powering robots and drones in consumer, enterprise, defense, industrial and logistics sectors.
-
product
E-Series Peak and Average Power Sensor, 50 MHz to 6 GHz
E9321A
The E9321A power sensor has a 300 kHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA wireless formats such as NADC, GSM and EDGE.
-
product
Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCI-1564
32 bit, 33 MHz, PCI interfaceInput channels32 isolated digital input channels, 24 V, incl. 16 interruptible and 3 fast counter inputsInput channels organised in 4 groups of 8 channels, each group has its own ground lineVoltage reversal protectionAll inputs are filteredOutput channels32 isolated digital output channels, 10 to 36 VOutput current per channel 500 mAWatchdog for resetting the outputs to "0"After power/ON the outputs are reset to ì0îShort-circuit current for 16 outputs ~ 3 AShort-circuit current for 32 outputs ~ 6 AShort-circuit current per output ~1.5 AElectronic fuseOvertemperature and overvoltage protection24 V power outputs with protection diodes and filtersSpecial output capacitors minimise electromagnetic emissionsExternal 24 V supply screened through a protection circuitryShutdown logic when the external supply voltage drops unter 5 V
-
product
Laboratory Instruments
Communicating 60,000-count TRMS benchtop multimeter for a broad range of applications in electronics and electrical engineering (1,000 V Cat. III) .
-
product
Double Ridged Waveguide Horn
DRH67
Frequency range: 6 GHz - 67 GHz VSWR (max): < 1.9:1Impedance: 50 O (Ohm)Connector: 1.85mm female Power (CW / Peak): 5W / 10 W
-
product
6 MHz Level Test Set ET 92
ET 92
100 Hz to 6 MHz selective/wideband Level Meter & Generator, with Spectrum Analyser
-
product
NDX OOB Gateway
The Kronback Tracers NDX OOB Gateway is placed in the headend for NDF/NDR - narrowband digital forward/return interfacing. It consists of 3 NDF inputs (70 to 866 MHz) and 6 NDR outputs (5 to 65MHz). Each of the 3 NDF inputs transmits one narrowband range up to mode 7 (25.6 MS/s), including the full FM band 87.5 to 108 MHz. Each of the 6 NDR connectors outputs up to three narrowband signals from the RPD with a bandwidth up to mode 6 (5.12MS/s).
-
product
Chassis - up to Twelve 8x1 or 4x2 Modules & up to Six 8k Modules
HXV/96-MF
These Chassis controls up to 12 8x1 modules, 12 4x2 modules, or up to 6 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
