CAT 6
Category 6 cable.
-
product
Low Voltage Boards
- 6 or 8 independently controllable full floating channelsup to 64 V- Up to 60 W Max channel output power- High resolution on voltage set- Programmable TRIP parameter- Programmable ramp up / down- Current generator operation in overcurrent condition- Overcurrent programmable protections- Individual remote sense lines- Up to 0,2 mV voltage monitor resolution- Up to 1 mA current monitor resolution- Voltage ripple smaller than 3 mVpp
-
product
Guided Wave Radar Sensors
LVRD10 Series
The LVRD10 Series guided wave radar transmitters provide continuous level measurement with a 4 to 20 mA signal output. Offered in single rod, coaxial, or weight & cable probes in 3 or 6 foot lengths
-
product
PXI High Density Precision Resistor Module, 6-Channel, 4Ω to 22.3MΩ
40-298-054
The 40-298-054 is a high density programmable resistor module with 6 channels which can be set between 4Ω and 22.3MΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Multi-Bay Connector Kit with Sides Installed
HW-56
6 each. Screws, nuts and washers (multi-bay connector kit with sides installed).
-
product
Sewer Pipe Scanner
ES-620
The ES-620 series of Electro Scan products are designed for scanning sewer pipe from 6 to 60 inches in diameter. Two products, designed for direct integration to your existing CCTV Truck include the ES-620 for 6 to 20 inches in diameter and the ES-2060 for 20 to 60 inches in diameter.
-
product
6-24V Heavy Duty Circuit Tester
1668E
Peaceful Thriving Enterprise Co Ltd
Check on 6 , 12V and 24V systems. To indicate whether there is an electrical potential at any low voltage point in the system. By using the pointed contact tip to pierce insulation on cables, it will also indicate if current is present. This can be helpful when tracing faults or add cable to a circuit.
-
product
CAT IV 600 A TRMS Navigator Clamp Meter
ACD-50NAV
ACD-50NAV clamp-on power meter offers AC current measurements to 600 A, AC/DC voltage to 1000 V, and wide jaws to accommodate large conductors. This clamp-on multimeter is ideal for industrial power monitoring and verifying system conditions.
-
product
PXI Dual 6 to 1 RF Multiplexer 6GHz 50 Ohm SMA Terminated
40-881-002
The 40-881 is a 50 Ohm 6 to 1 6GHz multiplexer available as a single or dual MUX in one and two PXI slots respectively. The 40-881 exhibits low VSWR characteristic over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensure a long service life with no wear out mechanism, making the 40-881 ideal for ATE systems requiring frequent and fast operating RF switching with no contact bounce.
-
product
Power Supplies
CUL-550B
The CUL-series is a semi-modular power supply that lets you select the cables you need while powering your gaming system with a 140mm Blue LED cooling fan and 6 pin PCI-E ready. **850W & 950W is offering 140mm Blue LED cooling fan & Dual 6+2 PCI-E ready. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power & 4+4 pin CPU connector are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
product
Impedance Analyzer 10MHz-20Hz
IA1021
Feature Specifications: Dual test mode: Analyzer(frequency sweep) and LCR(single frequency).Measurement frequency: 20Hz to 10MHz, 6 digitsFrequency resolution: 0.001% in all frequency rangeFrequency accuracy: 0.01%.DC bias(program): -10V ~ +10V, 0.005V resolution, accuracy 0.5%.Measurement basic accuracy: Impedance +-0.2%, phase: +-0.1°.Display Range: Z: 0.0000Ω-99.999MΩ.
-
product
PXI-5421, 43 MHz Bandwidth, 1-Channel, 16-Bit PXI Waveform Generator
778697-01
43 MHz Bandwidth, 1-Channel, 16-Bit PXI Waveform Generator - The PXI‑5421 is a 43 MHz arbitrary waveform generator capable of generating user-defined, arbitrary waveforms and standard functions including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -6 V to +6 V and uses direct digital synthesis (DDS) to precisely generate waveforms. The PXI‑5421 also features advanced synchronization and data streaming capabilities.
-
product
SFG Spectrometer
Ideal laser spectroscopy tool for in-situ investigation of surfaces and interfaces. SFG spectrometer operates from 4300 to 625 cm-1 and provides < 6 cm-1 spectral resolution. The heart of the system is a picosecond Nd:YAG laser generating 25 ps pulses that pump an OPG/DFG delivering from 260 to 20 µJ per pulse across the IR range
-
product
LXI Microwave Multiplexer, SP6T, 10-Bank, 18GHz, 50Ω, SMA
60-800-110
Our 60-800-110 is a 10 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Outdoor Infrared Motion Sensor
ENVIROMUX-IMD-O
Outdoor weatherproof - high reliability against water and insects. Double conductive shielding to eliminate false alarms from light sources. Registers movement in the area covered: 40 ft (12 m) x 50 ft (15 m) - 120° wide. LED lights during detection. Selectable detection paterns: Multi-Level (40 zones) or Pet Alley (18 zones). Unwanted detection areas can be eliminated using the included area masking strips. Selectable Sensitivity: High, Mid and Low. Adjustable to the brightness of surrounding environment with the Day/Night Mode switch. Tamper switch opens when cover is removed. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: -4 to 122°F (-20 to 50°C). IP54 compliant. Powered by ENVIROMUX-2D/5D/16D.
-
product
Primus Epic Interface Kit
LANTAP-10
Innovative Control Systems, Inc.
*LANTAP-10 kit comes with 10’ Coaxial cable, 6’ USB cable, 6’ CAT5 cable, BNC Connector and Terminator.*Allows connection of any 10/100/1000 Ethernet equipped system to EPIC equipped *Aircraft LAN or ANY 10base2 need.*No drivers to install. The LANTAP is NOT a USB device. It is only powered by USB.*Complies to IEEE 802.3 10Base-T and 10Base2*LED diagnostics and monitoring indicators
-
product
HDMI/DVI Receivers
HDMI® receivers and DVI receivers remain in high demand for professional, consumer, and automotive video applications, with HDMI nodes constantly increasing. Analog Devices offers a range of HDMI/DVI receivers that enable high quality conversion of digital video data to formats such as HDMI, MIPI, and TTL. Applications include video distribution, gaming, and HDMI/DVI consumer device connectivity for automotive infotainment systems. Our portfolio of HDMI receivers and DVI receivers offers competitive advantages such as automotive qualification, superior HDMI/DVI equalizer performance, comprehensive audio extraction, and small packages (6 mm × 6 mm, 0.5 mm pitch BGA).
-
product
PXI 4 Slot BRIC 276x8 Dual Analog Bus (6 sub-cards)
40-560A-021-276X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Bluetooth PCIe Combo Module
SX-PCEAX
The Silex’s SX-PCEAX is one of the industry’s first Tri-band Wi-Fi 6E modules. This Wi-Fi 6E module extends the benefits that Wi-Fi 6 already provides in the 2.4 and 5 GHz bands to 6 GHz and helps increase overall capacity and performance. SX-PCEAX is a tri-band IEEE 802.11 abgn/ac/ax WLAN module plus Bluetooth 5.2 BR/EDR/LE combo module based on Qualcomm’s QCA2066 SoC.
-
product
Footspacing Kit
10759A
The Keysight 10759A Foots pacing Kit, included in the Keysight 55282A Flatness Accessory Kit, provides three precision baseplates with 50.8 mm (2 in), 101.6 mm (4 in) and 152.4 mm (6 in) pad spacing. As an accessory to the Keysight 5530Laser Calibration System, the kit simplifies the mounting of the flatness mirror used in flatness measurement applications. The Keysight 10759A minimizes the grid setup and data accumulation time required for plate calibration.
-
product
Junior Set and Kits
Contents* AM-510-EUR (Digital multimeter)* ACD-10 PLUS (Digital current clamp)* TPP1-C1 (contact thermometer)* EU-200 (test lead set with 2 leads), 2 test prods (4 mm), 2 crocodile clips (CAT III/1000 V)* Hard carrying case
-
product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 3 Channels, 2.5 GS/s on 6 Channels, 1.23 GS/s on 12 Channels
DN6.225-12
The digitizerNETBOX DN6.22x series allows recording of up to 24 channels with sampling rates of up to 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
product
Handheld Oscilloscopes, 100 MHz, 2 Analog Channels
U1610A
100 MHz2 analog channelsTroubleshoot in any weather with channel-to-channel isolation and a CAT III 600 V safety ratingIdentify glitches easily with dual window zoomView subtle signal details more clearly with up to 1 Gsa/s sampling rate and 120 Kpts memoryDebug under any lighting conditions with 3 selectable viewing modes (indoor, outdoor and night vision)Get 3 instruments in 1: a dual-channel oscilloscope, built-in DMM and data loggerEasier start-up with 10 selectable languages
-
product
Digital multimeter, 6 digit
34461A
Color, graphical display with built-in bar chart, histogram, trend, math, and statisticsI/O: USB, LAN/LXI, GPIB (optional)BenchVue software enabled: Do more with your PC and instrument together, no programming required. Easily control your DMM, quickly build automated tests, log measurements and save precious time.
-
product
Coaxial Fixed Attenuator, DC to 26.5 GHz
8493C
The Keysight 8493C coaxial fixed attenuator provides precision attenuation, flat frequency response, low SWR over broad frequency range at a low price. The attenuator has APC-3.5 connectors and is available in nominal attenuations of 3 dB and 6 dB, also 10 dB increments from 10 dB to 40 dB.This attenuator is swept-frequency tested to ensure it meets specifications at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
product
Blackbody System
IR-2106/301
Infrared Systems Development Corp.
Infrared Systems Development introduces a NEW Low-Cost 6” x 6” Thermo-Electrically cooled / Heated blackbody source with a temperature range of 5ºC to 150ºC. The solid Copper Emitter plate provides superior uniformity and energy emission. Our Proprietary High Emissivity Black Coating provides >0.95 uniform Emissivity from 0.8 to 30 um.
-
product
Unequal Split Power Tappers
Pasternack unequal split power tapper product designs are also known as unequal couplers, power dividers or splitters, cross band couplers and signal samplers. Many of our unequal couplers / tapper series are RoHS and REACH compliant. Unequal RF tappers from Pasternack are available with 4.1/9.5, 4.3-10, 7/16 DIN and Type N connector options. These unequal split power tapper components for RF are manufactured to precise specifications required for accurate specified values listed for each product. Unequal split tapper products work with high power of up to 300 watts depending on style. Frequency ratings for unequal power splitter line are wide band components with a 380 MHz to 6 GHz frequency range, based on model selected. Pasternack RF power tappers in unequal design can be ordered with various directivity (dB) values of 4.8dB, 5dB, 6dB, 7dB, 8dB, 9dB, 10dB, 11dB, 12dB, 13dB, 15dB, 16dB, 20dB, 30dB depending on model. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this unequal split power tapper/coupler/divider series for RF is in-stock. These unequal split power tappers are not just in stock, but they will also ship the same-day are they are purchased.
-
product
InfiniiMode Active Differential Probe, 6 GHz
N2752A
The N2752A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2752A probe’s InfiniiMode provides the following modes of operation.
-
product
Circuit Breaker Analyzers & Timers
CAT Handheld Series
When it’s not practical to use conventional robust circuit breaker analyzers, a handheld circuit breaker analyzer and timer may come handy. DV Power has developed a unique CAT Handheld series. It is specially designed for testing of circuit breakers with one break per phase. Their compact and ergonomic design can provide a wide range of features and reliable operations in low, medium and high-voltage substations or in industrial environments.CAT Handheld series consists of two models, CAT-P and CAT-H. Both of them have a large (5,7 in) colored touch screen display. Because of that, test results are visible in dark places as well as in bright sunlight.Powerful internal Li-Ion battery of the instruments can last up to 8 hours of testing without recharging.CAT Handheld series records:main contacts operating times,contact synchronization,sequence time,a resistance of pre-insertion resistors,open and close coil currents,main contacts bounce time,auxiliary contact time,DC Voltage.Multiple operations, such as Open-Close and Open-Close-Open, can be initiated by using a predefined delay time or by triggering signal from current clamps connected to circuit breaker coil.CAT-H is capable of performing a coil control, while this feature is optional at CAT-P instrument. In contrast to CAT-H, CAT-P instrument can execute “First Trip” test.Both instruments display numerical and graphical results. Because of that, a user can easily overlay up to 4 records in the graphical form and make a quick on-site analysis of potential defects.A user can download test results to a PC via Bluetooth interface for more detailed analysis using DV Win software.
-
product
Digital Infrared Thermometer
IR-101A
Shenzhen Calibeur Industries Co., Ltd..
'-Temperature Range: -50℃ ～ 280℃(-58~536℉);'-Accuracy: ±2.5% of reading or ±2℃(4 ℉);'-Field of View: 6:1; '-Emissivity: 0.95 fixed'-Backlight'-Data hold'-Size: 95*55*30mm'-Weight: 74g'-Power: 2 * AAA Battery (not included)
-
product
PCIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PCI FlexRIO Digitizer Device
785595-01
The PCIe-5775 is a PCI FlexRIO Digitizer Device that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PCIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications.
