Filter Results By:
Products
Applications
Manufacturers
Up Converters
Increase the frequency of a signal.
-
product
125-Watt DC/DC Converter, 3U cPCI
55LQ3
NAI’s 55LQ3 is a 125 Watt DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This modular, switching power supply accepts +28 VDC input and provides a single output at up to 100 Watts.
-
product
Interface Converter
ZET 7070
Basic delivery scope with digital transducers for laboratory use includes the following: interface converter ZET 7070, power supply module 220V→ +24V, measuring line connector ZET 7001 (these components are mounted on a din-rail 300 mm); cable USB 2.0 A→B – length 1,8 m; terminal resistance 120 Ohm (for industrial use — steel plug); CD with ZETLAB SENSOR software, enabling connection of up to 60 digital sensors; set of operational documentation.
-
product
PXIe-4303 , 24-Bit, 32-Channel, 51.2 kS/s, ±10 V PXI Analog Input Module
783866-01
24-Bit, 32-Channel, 51.2 kS/s, ±10 V PXI Analog Input Module—The PXIe‑4303 is a filtered input module for voltage, thermocouple, and current measurements. The module offers you the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
product
PXI/PXIe Analog Output/Current Loop Simulator Module - 12 Channel
43-765-002
The 41/43-765-002 is a 12-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
RS232 to DMX Converter
DS232
RS232 to DMX Converter Controller Driver. Connect an RS232 terminal or computer port and drive DMX controlled dimmers and devices. A set of commands and auto fade rates offer power and flexibility for controlling DMX equipment. Use any RS232 terminal application to create command strings to: turn on, off, fade up, and fade down dimmer 256 DMX channels.
-
product
RS-232/RS-485 Converter
ECD485
Deploy sub-metering sites and simple metering networks with ease using the EDMI MiniHub RS-232 to RS-485 converter.1/4 Load RS-485 modules allow for up to 128 devices over 1.2km of wired daisy-chain network, with each meter capable of becoming the Network Master and remotely connecting to a backhaul system via an integrated EDMI Modem Port redirect connector.
-
product
Scalar Mixer / Converter Measurements
S95082B
The S95082B scalar mixer / converter measurements software provides an intuitive and easy-to-use user interface for setting up mixer and converter measurements with single or dual conversion stages. It controls the analyzer’s built-in source(s) and external signal generators for use as LO signals.
-
product
Programmable Multifrequency Clock Synthesizer - PMC
Model 7191
- Simultaneous synthesis of up to up to 5 different clocks- Eight SMC clock outputs- Ideal for A/D and D/A converter clock sources- Typical phase noise: -105 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 or 100 MHz- Four programmable VCXOs with 32-bit tuning resolution- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 700 MHz- Control and status via PCI bus interface
-
product
Radiation Microdosimeters
Teledyne e2v HiRel Microdosimeter is a compact hybrid microcircuit which directly measures total ionizing dose (TID) absorbed by an internal silicon test mass. The test mass simulates silicon die of integrated circuits on-board a host spacecraft in critical mission payloads and subsystems. By accurately measuring the energy absorbed from electrons, protons, and gamma rays, an estimate of the dose absorbed by other electronic devices on the same vehicle can be made. The Microdosimeter can operate from a wide range of input voltages. The accumulated dose is presented to three dc linear outputs and one pseudo-logarithmic output giving a dose resolution of 14 µrads and a measurement range up to 40 krads. These outputs are intended to be directly connected to most analog-to-digital converters (ADCs) or spacecraft housekeeping analog inputs (0-5 V range), which makes minimal demands on the host vehicle. The Microdosimeter incorporates a test function to allow electrical testing of the hybrid without the need for a radiation source.
-
product
Hi-Res Radar Scan Converter PMC
Eagle-2
Curtiss-Wright Defense Solutions
Eagle-2 is a high-performance radar scan converter from Curtiss-Wright Defense Solutions. Eagle-2 provides improved performance and support for high-resolution screen displays up to 2560 x 1600, including 2048 x 2048, making it the perfect choice for high-end radar display applications such as air traffic control (ATC) displays, VTS display command and control consoles, and radar head monitors.
-
product
Photoreceiver
A lightwave digital receiver module designed for OC-192, DWDM, and Bit Error Rate Testing (BERT) of a digital optical link. The LRD-10-M is an O/E converter with post/limiting amplifier module designed for use in receivers up to 12.5 Gb/s data optical transmission systems.
-
product
MODEM ELIMINATOR
The UDC-ME allows two DTE devices (such as routers) to communicate within proximity of each other. The UDC-ME transmits data bi-directionally at clock rates of 1.2k up to 3.072Mbps between DTE devices. The unit is equipped with two interface slots that allow a host of serial interface cards to be utilized. The serial interface cards available are RS-232, RS-422/449, RS-530, X.21, V.35 and HSSI. The Serial Interface cards are interchangeable and may be mixed such as RS-232 to V.35 thus eliminating the need for an interface converter or changing expensive serial cards on a DTE device such as a router.
-
product
Compact Converters
Virginia Diodes offers compact converters (CCs) for frequency up and down-conversion. These converters are easy to use and well suited for high performance up and down conversion of wide band modulated millimeter-wave signals. VDI CCs offer full waveguide band coverage and are available from WR28 (22.5-40 GHz) to WR2.2 (330-500 GHz) with additional CCs under development. Compact converters can typically be delivered within 9-11 weeks ARO or less. Contact VDI for more information.
-
product
PXI Analog Output/Current Loop Simulator Module - 4 Channel
41-765-004
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
PCI Data Acquisition Boards
AD8S-100DMA Series - Single low-spur 8-bit, 100 Ms/s
Model AD8S-100DMA is similar to the AD8-100DMA, has a single low-noise eight-bit 100MSPS A/D converter and can acquire up to 100 MS/s on a single channel into the host system's RAM. Drivers for 64 bit Linux and Solaris operating systems included.
-
product
Synchro to Digital-Resolver to Digital Converters
SDT RDT
Computer Conversions Corporation
The SDT/RDT Series, are single module, tracking, Multi-speed synchro/resolver to digital converters designed for Military and Industrial Applications. They will accept Electrical Multi-speed, or Geared (dual speed) Multi-turn; Synchro or Resolver input sets (Fine/ Coarse), having the most standard ratio’s, and convert them into a single non-ambiguous 16 Bit data word with up to +/-20 arc. seconds accuracy.
-
product
Miniature Airborne Communications Converter
MACC II - Converter
Excalibur’s MACC II represents a third option. A proven, low risk, low cost, off the shelf product that translates between different communications specifications. The MACC II can solve your communications problems without R&D costs and without schedule risks while still providing you with the flexibility to customize the system to your specific needs.The MACC II is a wholly contained Miniature Airborne Communications Converter (data converter - protocol converter or translator). The MACC II can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to AnalogPlease see multi protocol 8000 modules for additional information on protocols that can be used on the MACC II.
-
product
Portable Density/Specific Gravity Meter
DA-130N
Measuring method Natural Oscillation typeMeasurement object Liquid sample test materialsRange 0.0000 ~ 2.0000 g/cm3Precision 0.001 g/cm3Resolution 0.0001 g/cm3Temperature range 0 ~ 40.0CTemperature compensation Up to 10 entries for temperature compensation coefficient and converted temperatureAutomatic calibration All density values of pure water needed for auto calibration can be stored.Number of data 1,100 samplesExternal outputPC or Printer can be connected. (not both) IrDA interface is standard equipped. Connection via RS-232C requires optional infrared RS converter (98-029-0007).
-
product
16 A/D Channels (±1.25 to ±10.0 VDC FSR or ±25 mA) ; 16-bit SAR, 8 Chx2 A/D multiplexed
AD4
Module AD4 features 16 channels with up to 16-bit SAR A/D converters for one per 8 channel multiplexed bank / 2 banks. The maximum programmable, expected full-scale range input for the AD4 module is ±10.00, ±5.00, ±2.50 or 1.25 volts where range is -FS to +FS, 0 to FS VDC, or ±25 mA. The A/D converters have programmable sample rates of up to 500 kHz / Aggregate per bank of 8 Channels.
-
product
High Voltage Power Supplies
The mains voltage (230V / 3 x 400V) is transformed, rectified and filtered by the HN series. The direct current output voltage is tuned by a variable transformer or regulated by a thyristor controller. With the HS and HV series the rectified mains voltage is supplied to a frequency converter, which produces a mid-frequency square wave voltage. This transformed, rectified and filtered alternating current produces the desired voltage as output, which is regulated by means of frequency variation or pulse width modulation. The equipment in the HV series supply, in addition to the high voltage output, up to 3 auxiliary outputs which can be used to supply e.g. heating, grid voltage or surge voltage.
-
product
12 A/D Channels (±100V max); 24-bit Sigma-Delta
AD2
Module AD2 features 12 channels with up to 24-bit Sigma-Delta A/D converters for each individual channel. The maximum programmable, expected full-scale range input for the AD2 module is ±100.0 to ±12.5 VDC respectively. The A/D converters have programmable sample rates of up to 256 kHz.
-
product
Digital Three-Phase Uni & Directional Converters
Start Power equipments series SCxQML230 are totally controlled three-phase digital converters operating up to 500 Vac voltage, 360A current, frequency between 45 and 62Hz; they are suitable for speed and motor torque regulation. Sizes with current up to 9000 A are available in different mechanical dimensions.
-
product
P104 Synchro/Resolver Simulation Board
73DS2
NAI’s 73DS2 is a PC104-compatible Synchro/Resolver Simulation Board with three isolated channels. These channels can incorporate up to three Digital-to-Synchro/Resolver Converters with 1.2 VA drive capability in a stack-through module. With galvanic isolation, one of the outputs can be grounded without affecting performance.
-
product
In-line ICP® Charge Converters
In-line ICP® charge converters play a vital role in converting high impedance charge mode piezoelectric sensor signals into low impedance voltage signals, facilitating input to readout, recording, and analysis instruments. Specifically engineered for compatibility with high temperature piezoelectric sensors, these units are capable of operation in environments reaching up to 500°F (260°C). The series boasts ±2.5V or ±5.0 V output, offering a range of gain options, all packaged within a compact and durable casing. As a cost-effective alternative to laboratory charge amplifiers, in-line ICP® charge converters present an appealing choice for multi-channel applications.
-
product
P104 Synchro/Resolver Measurement Board
73SD4
NAI’s 73SD4 is a DSP-based, PC104-compliant Synchro/Resolver Measurement Board with six separate, isolated channels. These channels can incorporate up to six Synchro/Resolver-to-Digital Tracking Converters in a stack-through module. Each channel also produces differential incremental encoder (A & B) outputs (with programmable resolution) and a zero-degree marker pulse. Commutation outputs are available for 4-, 6-, or 8-pole brushless DC motors that eliminate the need for Hall Effect sensors, thereby reducing both processor time and bus traffic.
-
product
STANAG3910/EFEX Test And Simulation Module for Standard Ethernet
ANET3910
STANAG3910/EFEX Test and Simulation module for Standard Ethernet. The ANET embedded Linux Operating System gives the unique capability to run the optional PBA.pro Engine right in the box. Another option is the ANET-ADK onboard software development kit where users create run-time applications (e.g. STANAG3910/EFEX to Ethernet Converter, STANAG3910/EFEX to Ethernet Gateway) to execute right in the box. For wireless applications, an ANET compatible USB Wifi dongle is optionally available.The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
product
Gas Analyzers
Independent Handheld 5 Gas Analyzer or use with MODIS™ Link, VERDICT® and VERUS® Bluetooth® link. Fully Portable 5 Gas Analyzer, go anywhere, use anywhere 110 V AC and 12 V powered Internal rechargeable battery, up to one hour of use Ideal for road testing and mobile use Measures exhaust emissions for CO, CO2, HC, O2, NOx and AFR/Lambda Provides an instant assessment of an engine vehicle exhaust and catalytic converter MODIS, VERDICT® and VERUS® Link for enhanced real-time viewing Setup required with included software on USB stick Gather all the evidence required for effective and accurate vehicle diagnostics on one screen in real time View, graph, save and recall data Monitor and reduce vehicle emissions, improve driveability and fuel efficiency There are 255 memory locations in the analyzer to track and print data for the same or many different vehicles Compatible with gasoline, CNG, propane and diesel fuel types Annual calibration and sensor replacement performed at Crystal Lake Northern Repiar enter Meets required industry standard
-
product
UP Converter
The products have a big Dynamic Range, are highly linear and have low Noise Figures to keep the best possible quality of the signals to be converted. For this reason an internal filter for secondary wave suppression is implemented.
-
product
DC Electronic Load
DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more.
-
product
MMW Downconverters
Innovative Technical Systems has designed numerous microwave and millimeter-wave downconverters for a variety of applications. Typical downconverters include balanced mixers, phase-locked local oscillators, LO multipliers, and output IF amplifiers. RF LNAs are also provided for many downconverters up to 100 GHz.These downconverters can be designed for numerous communications, radar, and instrumentation applications. We will customize these converters for frequency coverage ,noise figure, gain, and mechanical form-factor.
