Breaker
-
product
Primary Test Equipment
LET-400-RD
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.The regulation system is based on a continuously variable autotransformer (Variac) that supplies to a power transformer that delivers the high current outputs and isolate the main supply from the load. A built-in ammeter and a timer gives the information about the current value and the operation time of the relay or breaker under test.
-
product
Dynamic Micro Ohm Meter
PRIME 600
It is the only micro ohm meter in the market that integrates both the contact resistance and the dynamic resistance measurement (DRM) for cost-efficient condition evaluation of contacts in SF6 and vacuum type circuit breakers; PRIME is a high current micro-ohmmeter that provides true pure DC with smart control up to 600 A, a wide measurement range with high power, dual ground testing process, thermal printer, touch display, pre-defined test modes and automatic reporting.
-
product
Power Distributor
AV-P3040
"AV-P3040" can supply 40A (20A x 2). The power supply can be wired directly from the distribution board and equipped with two 20A breakers.
-
product
Environmental Chamber
REXMED REC-280
MOD. REC-280, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,140 Watts, 10,700 BTU/hr, 2,702 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
Volt-Finger Detector / Driver
LVD-18
Standard Electric Works Co., Ltd
● Bright LED and audible alarm sound when voltage is present.● Designed for both contact and non-contact voltage detection.● Direct contact voltage detection: 50V~600Vac.● Non-contact voltage detection: 50V~600Vac.● Can be used to detect voltage in lighting fixtures, circuit breakers.● Compact and handy.● Can be used to find a break in a wire.● Continuity test and basic driver function..● Flashlight.
-
product
Contact Resistance Meter
CRM 100C
CRM 100C directly measures resistance values with DC current injection under live switchyard conditions.The CRM 100C is specially designed to reliably measure contact resistance of Circuit Breakers, Isolators, Bus Bar joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards. It can also be used for testing cables, graphite bars etc.
-
product
Enlarge Environmental Chamber
REXMED REC-480
MOD. REC-480, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 5,270 Watts, 18,000 BTU/hr, 4,545 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
3 Wire (Analogue) Earth Resistance Tester
2105 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
product
Miniature Circuit Breakers
Mors Smitt offers a wide range of railway hydraulic magnetic circuit breakers. The circuit breakers are fully configurable to meet the individual requirements.
-
product
3 Wire (Analogue) Earth Resistance Tester
4105 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
product
C/I Tracers
*Advanced bi-directional sensing technology*Superior sensitivity and functionality providing for accurate tracing and locating*Ergonomic receiver with information-rich full-color graphical LCD*Visuals and audible signal provide quick and easy to understand tracing feedback*Traces concealed wiring, locates junction boxes, and finds breakers for live or open circuits*Locates and identifies blown fuses*inds shorts and breaks in conductors
-
product
Measuring Display Unit Breakers
Mitsubishi Electric Automation, Inc
Measuring display units (MDU) are integrated with molded-case circuit breakers and earth leakage circuit breakers for measuring, displaying, and transmitting information on cable ways. This display unit closely monitors energy consumption by measuring current, voltage, power, electric energy, harmonic current, leakage current and power factor.
-
product
Power Factor RLC Load
3282（280V,1875W / 3700VA ）
3282 power Factor RLC Load built-in 16-bit A/D and DSP precision measurement circuit, provides accurate measurements, measurement items have Vrms, Arms, Watt, VA, CF, PF, THD, VTHD, ITHD, Ipeak, Amax, Amin, Vmax, and Vmin. In addition to these measurement functions, it also provides time measurement，products such as UPS, fuses and circuit breakers etc. trip or blow time and transfer time for Off-line UPS
-
-
product
Comparative Tracking Index Tester
The Comparative Tracking Index Tester is used to test the resistance to tracking of solid insulators or parts of insulators used in electrical appliances and accessories. This test is mandatory for manufacturers of most of the electrical products such as circuit breakers, meters, switches, sockets, plugs, starter holders, connectors, etc.
-
product
Intelligent Circuit Protection
The Mors Smitt ‘Intelligent circuit protection system’ controls and monitors all AC and DC circuit breakers remotely and is capable of providing complete status of all MCB’s via display or through the Train Management System.
-
product
15 Amp 120 VAC Filter and Surge Arrestor
AS-AC15
- 15 amp 120VAC quad outlet for high power devices- Resettable circuit breaker protection, easy to use and reset- I EA standard input plug and #14 GA AC line cord for USA - standard interface- MOV surge arrestors included - for even more protection- High level of common mode and differential mode filtering digital noise and RF filtering eliminates- digital artifacts and RF interference - See chart- Front Panel Neon Blue AC ON indicator - just plain cool to look at, not too bright!- Double shielded box inside - for optimum filtering operation- Size 6W X 4H X 4 3/4 D in inches approx 3 lbs
-
product
Circuit Breakers
As the premier supplier of power system components, Interpower has what you need to complete your projects, including circuit breakers. Interpower has no minimum order requirements, plus same day shipping is available on in-stock Interpower products.
-
product
Power Supplies
AC and DC power supplies are used for providing the power required for energising the trip and close coils of the breaker and for running the spring charging motor. The appropriate AC or DC configuration of the power supplies can be selected, depending on the DUT specifications of the manufacturer. Dual-mode AC/DC power supplies capable of providing AC and DC outputs from the same power supply are also available, if required by the user.
-
product
Dynamic Contact Resistance Meter
Dynamic contact resistance measurements are necessary to understand the condition of the arcing contacts of the circuit breaker. Static contact resistance measurements do not give us information related to erosion of arcing contact, misalignments of the contact, and damages to the driving mechanism.
-
product
Primary Test Manager
The Primary Test Manager™ (PTM) software supports you during diagnostic testing, condition assessment and data management of medium- and high-voltage assets, such as circuit breakers, rotating machines, grounding systems, instrument and power transformers as well as bushings and on-load tap changers (OLTC).
-
product
Stationary Circuit Breaker Test System
ACTAS C160
Stationary test system for carrying out fully automatic final factory tests, type and function tests on all kinds of switchgear devices, such as circuit breakers, disconnectors or earthing switches, regardless of the type of drive unit. All the electrical and mechanical parameters needed for the assessment of switching performance are measured in real time and evaluated without either the main contact chambers or the drive unit having to be opened. The system has analog and incremental input channels for the acquisition of analog quantities.
-
product
Lock Out Kit
LOKKIT1
The Martindale universal lock out kit is compatible with most circuit breakers. It is supplied with a padlock that has its own unique key, and a safety hasp that enables multiple users to lock off with space for up to 6 padlocks.
The full 16 piece kit includes: 1 x Padlock with unique key, 1 x Steel safety hasp with space for up to 6 padlocks, 1 x Green mini MCB lock, 1 x Yellow mini MCB lock, 1 x Blue medium MCB lock, 1 x Large red MCB lock, 1 x Small red MCB lock, 1 x Red fuse lockout breaker, 1 x Yellow fuse lockout breaker, 5 x Danger tags which can be overwritten, 1 x Black marker for writing on Danger tags, 1 x TC55 soft carry case
-
product
Contacts Resistance Tester
JYK II
•Instrument IPC architecture for domestic production of all models of metal contacts SF6 switchgear, GIS combination of electrical, vacuum switch, oil switch and column switches, contacts and so on.•Sensor: Acceleration speed sensor, rotation speed sensor, linear stroke sensorinstallation is very easy and simple.•Trigger: The trigger, external trigger, the sensor is triggered. Sensor can trigger the circuit breaker manually switching characteristic test, such as a manual column pole division switch.
-
product
Powerful AC/DC Power Supply For Testing Circuit Breakers
POB35AD
POB35AD is a power supply unit employing the latest power electronics technology. POB35AD generates ripple free DC-voltage and it is developed for regular maintenance tests of power circuit breakers. It eliminates use of stationary batteries during testing. Output voltage is selectable from 10 to 250V AC/300VDC. The test set is a powerful and versatile unit with possibility to generate up to 30A.
-
product
AC Electronic Load
AC&DC Electronic Loads are design for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources and other power devices such as switches, circuit breakers, fuses and connectors.
-
product
Wire Systems Analyzer
Console Test Systems (CTS)
Wire Systems Analyzer Commercial Roll around detects and locates faults and detects degradation in electrical interconnect systems ranging from simple to complex. Used to verify the operation of relays, circuit breakers, indicators, switches, diodes, transformers, 1553 couplers, etc.
-
product
Dynamic Micro Ohm Meter
PRIME 200
It is the only micro ohm meter in the market that integrates both the contact resistance and the dynamic resistance measurement (DRM) for cost-efficient condition evaluation of contacts in SF6 and vacuum type circuit breakers; PRIME is a high current micro-ohmmeter that provides true pure DC with smart control up to 200 A, a wide measurement range with high power, dual ground testing process, thermal printer, touch display, pre-defined test modes and automatic reporting.
-
product
3 Wire (Digital) Earth Resistance Tester
ST-1520
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Auto power off function.● The timer operates automatically for about three to five minutes when the "PUSH BUTTON SWITCH" and "TIMER ON BUTTON" are pressed together. This will keep test "ON" for the duration of the timer.● Timer for test function (count 3-5 minutes).● Battery operated.● Data hold function.● Small and light weight.● Calibration performed with supplied test leads.
-
product
Temporary Power Outlet
K-271, K-272, and K-273
Knopp’s Temporary Power Outlets are an easy and safe solution for construction sites or other areas where power is not easily accessible. The device provides temporary electric service by isolating power from the breaker panel. Easy-to-use and versatile, Knopp’s Temporary Power Outlet eliminates the need for portable generators and can be used for motor homes, travel trailers, marine shore power, construction sites, and solar pump stations. Emergency situations such as hurricane restoration, storm outages and fire damage can also utilize this device.
