AC Electronic Loads
Simulate voltage, current and power ranges.
-
Product
Attenuators & Loads
-
*High power handling 100W with a wide range of available attenuation values*Very low PIM <- 160 dBc with excellent return loss performance*Support for 7-16 or 4.3-10 connectors and optional 19 inch rack mount kit*Designed and produced to ISO 9001:2008 certification standards for reliability and quality
-
Product
Programmable AC Source
6500
-
Chroma Systems Solutions, Inc.
1200VA ~ 9KVADirect Digital Synthesis (DDS) waveform generationProgrammable voltage, current limit, frequency, phase, and distortion
-
Product
Signal / Micro Power/ Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Position, loaded w/twin female contacts
510160112
-
This module comes fully loaded with twin female contacts (p/n 610138200), iCon modules mount from the rear of the iCon/i1 receiver allowing installation and removal of pre-wired cable blocks. Primary mating module 510161107. (May mate with other ITA modules, as well.)
-
Product
Digital Electronic Scale
-
A type of electronic weighing machine, which is used to measure many readings
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD can also be extended with a 3rd or 4th eddy current brake.
-
Product
AC Power Sources
BPS Series
-
AMETEK Programmable Power, Inc.
The BPS Series consists of multiple high power AC power systems that provide controlled AC output for ATE and product test applications. This high power AC test system covers a wide spectrum of AC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the BPS Series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the unit to its designated location (using included casters), plug it in, and the BPS Series is ready to work for you.
-
Product
EQCM Electronic Quartz Crystal Microbalance
Elettra
-
Elettra has been designed to operate on its own, but it is also possible to connect it to a PC to control it and acquire, view and save data thanks to its extremely easy to use software that runs under MS-Windows™. The data acquisition process can be controlled extremely quickly thanks to the PLAY, PAUSE and STOP keys.
-
Product
AC Engine Dynamometer
DA750
-
Power: 750 hp (559 kW)Torque: 2,626 lb-ft (3,560 Nm)Maximum Speed: 3,000 rpmConstant Torque Range: 0 - 1,500 rpmConstant Power Range: 1,500 - 2,600 rpmDecreasing Power Range: 2,600 - 3,000 rpmRotation: bi-directional
-
Product
AC / DC Current Probe, 10 MHz, 150 Arms
N2781B
-
The N2781B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 150 Arms continuous
-
Product
Through Hole/ Donut Load Cell Compression Only
THA SERIES
-
Our THA Series through hole donut load cells offer an outside diameter of 1.00 inches and up to two different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
On Load Tap Changer Analyzer
TAP4
-
The TAP-4 is the first instrument to use vibro-acoustic measurement to perform tests on On-Load Tap Changers (OLTC). The TAP-4 is a universal device, it adapts itself to any type of transformers: MR Reinhausen, ABB, Ferranti, Federal Pioneer and others.
-
Product
40 kV AC Withstanding Voltage Tester
-
AllWin Instrument Science and Technology Co., Ltd.
Leakage current at real-time detectionAlarm value can be preset freelyAudio alarm, High-voltage breakdown protection
-
Product
Clamp type AC Current Sensor／with DC Voltage Output
ACT-50H
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For current measurements of the control board*AC 1A～50A*DC 5V full scale output
-
Product
Performance AC Power Source, 750 VA, 300 V, 6.5 A
6812C
-
Maximize your investment with five instruments in one device Increase your productivity with extensive built-in power measurement capabilities Flexible IO: LAN/LXI Core, USB and GPIB Lower your cost of ownership with global support & the longest standard warranty in the industry
-
Product
Large Telemetry Compressive Load Cell
TC-3.0-LG
-
DLM’s Telemetry Compressive Load Cells can be used independently or in combination as part of weighing platforms.They range from 100t to 300t and manufactured using high grade stainless steel, making these load cells particularly suited to rugged environments and the hire industry. Bespoke size compressive load cells can be designed upon request. Some applications include: tank weighing, hydraulic lifting operations, vessel weighing and certification.
-
Product
Power Supplies And Loads
-
Power Supplies and Loads power devices under test (DUTs) such as RF power amplifiers and cellular handsets. The power supply takes in AC power and delivers DC voltage with a fixed polarity, either positive or negative, to its load.
-
Product
AccuDyne™ AC Dynamometer Systems
-
SAKOR Technologies offers the AccuDyne™ series of AC motoring dynamometers. These 4-quadrant dynos offer full motoring as well as loading capabilities. AccuDyne dynamometers can be used for testing active components such as engines and electric motors as well as passive components such as transmissions, generators and alternators. AccuDyne dynamometers are available in models from 5 kW through 3 MW. SAKOR Technologies configures each AccuDyne system to meet customer-specific requirements.
-
Product
Variable Resistor Load Bank
REOLOAD 100
-
A variable resistor load-bank with fixed stages connected in parallel and switched in, as required, with an adjustable stage for fine trimming. Designed for testing equipment under load. 1000V (AC or DC). 250A and 2500
-
Product
S Beam Load Cell
-
Futek Advanced Sensor Technology, Inc.
FUTEK S Beam Load Cells (Tension/Compression) offer a compact design for a variety of applications. Available in standard and metric, the S Beam Load Cell series provides accuracy, compact design features, overload protection (select models), and a wide capacity range to choose from. S Beam Load Cells are also commonly known as Z Beam Load Cells or S Type Load Cells.
-
Product
1μΩ-4kΩ AC Milliohmmeter Low Resistance Tester
TH2521
-
Shenzhen Chuangxin Instruments Co., Ltd.
TH2521 AC Milliohmmeter is a high-performance and intelligent tester widely used to test contact resistance, internal resistance and battery voltage. The application of constant current source with 1kHz frequency can greatly eliminate the potential error caused by thermoelectricity on DUT. This meter has the function to automatically detect contact failures on test cable. At the range of 30mΩ, basic R resolution can reach 1μΩ. It is applicable for transformer, inductance coil copper resistance, relay contact resistance, switch, connector contact resistance, wire resistance, PCB line and via reistance dan metal defect detection, etc. In the mean time, signals, such as HIGH, LOW, PASS, can be output through HANDLER interface, thus it is very convenient to be used in automatic production line.
-
Product
Industrial Weighing - Wireless Load Cells
-
A wireless industrial weighing scale system can be advantageous, for instance when running conduit for cable is impossible, or if the cable could be damaged easily. In some cases the wireless interface is more economical than long runs of cable. These systems can be battery operated or hard wired to a power source if available. View our wireless load cell options below.
-
Product
AC DC Withstand Voltage & Insulation Tester (HI-POT)
SS71XX series
-
High voltage withstand and insulation tester (HI-POT tester) is used for testing insulation grade and withstanding voltage capability of electrical equipment, transformers, motor, relays, cables, electronic components, electronic applications, inductors, ignition coils, insulation wires, insulation tapes, valve coils, reactors, contactors, etc.
-
Product
Battery Load Bank
-
Foresight Electronics Co., Ltd.
Utility is used for battery systems range from 21-30V, if higher current is needed, two or more FST-24V units can be linked together. Discharge to Battery string voltage as 24V, Cell voltage as 1.2V/2V/6V/12V adjustable stop points and multiple alarm designs to control the discharge process intelligently 7inch LCD touch screen for easy operation and showing various parameters real time Support RS232 real time monitoring by PC or SD Card download data after discharge
-
Product
Electronics
-
Weidmüller Interface GmbH & Co. KG
Electronics lie at the heart of your automation technology. We give you solutions with intelligence.
-
Product
Micro Power or Micro Coax, SIM Insert, ITA, 26 GHz, 2 POS, 6 Slot (not loaded)
510181110
-
Micro Power or Micro Coax, SIM Insert, ITA, 26 GHz, 2 POS, 6 Slot (not loaded)Micro Power or Micro Coax patchcords need to be purchased separately.
-
Product
Electron Probe Microanalyzer
EPMA
-
JEOL commercialized the world's first FE-EPMA, the JXA-8500F in 2003. This highly regarded FE-EPMA has long been used in various fields, such as: metals, materials and geology in both industry and academia. The JXA-8530FPlus is a third-generation FE-EPMA that comes with enhanced analytical and imaging capabilities. The In-Lens Schottky field emission electron gun combined with new software provides higher throughput while maintaining high stability, thus allowing a wider range of EPMA applications to be achieved with higher resolution.
-
Product
Electronic Dendrometer
CRITERION RD 1000
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*BAF: Visually estimates if trees fall in or out of a given plot as related to the specified Basal Area Factor.*In/Out: Internally computes the limiting distance for questionable, borderline trees and determines if they are in or out of the plot.*Diameter: Determines the diameter of a tree at any given height.*Height/Diameter: Provides the ability to determine the height at which a specific diameter occurs.*Raw Inclination: Measures inclination in percent slope.
-
Product
Data Center Load Bank
-
Mosebach Manufacturing Company
Mosebach’s Data Center Server Rack load bank, the SR family, is ideal for commissioning data centers. There are multiple models for varying voltages and power levels. The unit has a variable fan speed control which allows you to fine tune as desired.
-
Product
Electron Multiplication (EM) Standard Image Sensors
-
EM (Electron Multiplication) is a technology that uses on-chip gain in the charge domain to effectively eliminate read noise from an image sensor. This enables advanced ultra-low light applications that require extreme sensitivity at fast frame rates. Examples include life science applications such as single molecule detection, super resolution microscopy and spinning disk confocal microscopy along with physical science applications such as nanotechnology imaging, Bose Einstein condensates and soft X-ray spectroscopy, and astronomy applications such as adaptive optics and lucky imaging. The inclusion of an additional conventional output allows further flexibility for applications such as true 24 hour surveillance.
-
Product
3-Phase Programmable AC Source
61700
-
Chroma Systems Solutions, Inc.
Power: 1500VA, 3 (61701); 3000VA, 3 (61702); 4500VA, 3 (61703); 6000VA, 3 (61704); 12000VA, 3 (61705)Voltage: 0~150V/0~300VFrequency: 15~1.2KHzPhase angle: 0~360Built-in PFC, provides input power factor over 0.98Advanced PWM technology delivers high power density in a compact rack-mountable packageBuilt-in output isolation relaysAC+DC output modeProgrammable slew rate setting for changing voltage (optional function)Turn on, turn off phase angle controlUser-definable power-on statusPower line disturbance (PLD) simulation capability (optional function)Comprehensive measurement capability: V, Irms, Ipk, I inrush, P, PF, CF of current etc.Programmable r.m.s. current limitFull protection: OP, OC, OV and OT protectionGPIB and RS-232C interface (optional)Easy-use software for operation
