Tan Delta Bridges
See Also: Tan Delta
-
Product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781209-01
Strain/Bridge Input Module
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
Product
PCIe X8 And X1 Bridge Card
-
The Guzik PCI Express Host Interface Bridge Card was designed to expand the x8 PCI Express Gen 2 (PCIe) slot in a host PC to an AXIe or a Guzik GSA 6000 chassis via a x8 PCI Express Gen 2 and a x1 PCI Express Gen 1 high speed PCI-SIG specified data cables. This allows the end node to connect to the host bus at speeds up to 3.2GByte/sec user data rate. The Bridge Card installs in a x8 or x16 slot of a PCIe backplane or a PCIe motherboard, provides additional board-based retention and reinforced front panel.
-
Product
50 Hz-20 kHz Ultra-precision Capacitance Bridge
AH 2700A
-
The AH 2700A offers unparalleled stability, resolution, linearity and accuracy in a multi-frequency capacitance/loss1 bridge (whether manual or automatic). Its numerous state-of-the-art features make it an exceptionally user-friendly instrument. The precision of the AH 2700A is creating new applications in calibration, science, and production in a wide range of fields
-
Product
Oil Tan Delta Tester
OTD
-
The Oil Tan Delta (OTD) is a laboratory instrument, which measures the Tan Delta, Resistivity and Relative Permittivity of insulating liquids. These tests give a wider picture of the overall quality of the insulating oil, and will indicate if there is any contamination. Megger has developed features of the OTD to ensure that productivity levels within laboratories are maximised. The microprocessor controlled inductive heater means that there is uniformity of temperature throughout the cell, in compliance with IEC 60247, and for cooling a fan effectively speeds up the cell cooling time. The instrument has a temperature measuring range of 10 to 110 C, with an accuracy of 1 C. It can be set to preheat before testing takes place. The automated oil drain facility negates the need to move the oil vessel. User safety is paramount and with this in mind, Megger have designed independent and dual redundant high voltage cut-off circuitry. If for any reason the user needs to abort the test, this can be done so by pressing any key, immediately terminating the test and removing the high voltage. The design of the cell components maximise oil fill rate but minimise turbulence in oil flow and eliminate trapping of air. With only 32 cell components, it is easy to assemble and disassemble.
-
Product
Coax, Patchcord, ITA, 36", Micro Coax, RG316DS Tan (Double Shield), Single-Ended
7-361117000-036
Coax Patchcord
Coax, Patchcord, ITA, 36", Micro Coax, RG316DS Tan (Double Shield), Single-Ended.
-
Product
(DCC) Resistance Bridges
-
Direct Current Comparator (DCC) Resistance Bridges. Unique innovations in 6622A design and modularity means users no longer have to decide what Bridge satisfies current requirements as well as future requirements. Optional modules allow for normal, high ohms, and low ohms measurements without having to purchase multiple bridges as per competitive products.
-
Product
Delta DC Rectifier Repair/Refurbishment
-
Delta DC Rectifiers are used by original equipment manufacturers to build On-Site Sodium Hypochlorite Generator Systems. These power supplies are generally operated at full load for 24/7 operations at high temperatures. Hence, these power supplies must be extremely rugged and must be de-rated significantly to achieve long operating life.
-
Product
USB Connectivity Bridges
USBXpress
-
Silicon Labs USBXpress devices are highly optimized solutions that enable designers to easily add USB to existing and new applications. These fixed function devices provide the easiest method to add USB without the need for any firmware or driver development. USBxpress portfolio supports several USB to serial bridge devices including human interface (HID) devices and USB Audio devices.
-
Product
4-Ch, 24-Bit, 25.6kS/s, Full/Half/ Quarter Bridge Input IDAQ Module
iDAQ-871
-
High resolution (24-bit)All types of bridges supported (full, half and quarter)Software-configurable and multiple bridge completion flexibilitySynchronization along with other iDAQ modulesMultiple trigger modes for flexible configured acquisition timingBuilt-in digital filter for higher SNR
-
Product
Bridge Coordinate Measuring Machines
-
Measurement results with high accuracy are particularly important for quality assurance. Bridge coordinate measuring machines from ZEISS have a precise probe system that convinces with high measuring speed. The various solutions and systems can be tailored directly to individual requirements.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
779521-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
4-Channel Motion Control And High-Speed Trigger And Module For The Bridge Connected To EtherCAT
ECAT-4XMO
Trigger Module
The ECAT-4XMO is EtherCAT SubDevice module with high-speed position comparison trigger and encoder re-drive function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications. Additionally, the ECAT-4XMO has 4-axis motion control with bridge function between EtherCAT and non-EtherCAT. Advanced motion control functions help machine and equipment builders to increase their motor selection portfolio, like linear, step, servo, direct drive, and AC motors, making it ideal for a variety of automation industry applications.
-
Product
DELTA™ III 3-zone Flow Ratio Controller
-
The DELTA™ III Flow Ratio Controller divides and controls mixed process gas flows to three chambers or zones within a process chamber at proportions specified by the user to optimize process uniformity and repeatability. Available with EtherCAT® or DeviceNet™ communications, this device provides the latest in gas flow ratio measurement and control technology.
-
Product
AC resistance bridges
-
Designed for precise, accurate, low noise, low excitation power AC resistance measurements. Measure resistance materials in cryogenic environments.
-
Product
Coax, Patchcord, Receiver, 72", Micro Coax, RG316 Tan, Single Ended
7-362116000-072
Coax Patchcord
Coax, Patchcord, Receiver, 72", Micro Coax, RG316 Tan, Single Ended.
-
Product
Coax, Patchcord, ITA, 36", Micro Coax, RG 316 Tan, to SMA Plug
7-361116525-036
Coax Patchcord
Coax, Patchcord, ITA, 36", Micro Coax, RG 316 Tan, to SMA Plug.
-
Product
Bridge Decking Testing Equipment
-
The testing process can detect blow holes, inclusions or thin areas in 'sprayed-type' membranes. Because the concrete contains a small amount of water, it is electrically conductive and a DC Pinhole Detector can be used to create a high voltage which is passed over the surface by the use of a brush electrode. An alarm will sound to identify any small defects which can be rectified so that the integrity of the coating can be verified.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
Full Bridge Thin Beam Force Sensors
TBS SERIES
-
The TBS Series thin beam force sensors many different parameters found in medical instrumentation, home appliances, process control, robotics, and automotive are exceptionally suited for small load measurements. They are designed to measure and many other high volume applications. A specially developed integrated strain gage includes all balancing, compensating and conductive elements and is laminated to the beam to provide excellent stability and reliability.
-
Product
Noise Bridge, RF 1 MHz to 100 MHz
MFJ-202B
-
Quickly adjust almost any antenna for maximum performance, 1 to 100 MHz. Lengthen or shorten your antenna for minimum SWR. Measure resonant frequency, feedpoint resistance and reactance. Works with any receiver or transceiver. Hand-calibrated resistance scale, expanded capacitance range and exclusive built-in range extender.
-
Product
Ethernet to Wireless Bridge
BR-100AH
-
BR-100AH is the first commercially available bridge supporting IEEE’s 802.11ah wireless standard which is a long-range technology which enables any Ethernet device to become an 802.11ah wireless network device, giving the freedom to place it anywhere in your facility. BR-100AH is all that you need to incorporate your device into your 802.11ah (HaLow) network. A benefit of 802.11ah is extended range, making it useful for long distance and rural communications.
-
Product
Wireless Bridge Device
BR-300AN
-
BR-300AN is a wireless bridge device which can easily convert a 10/100/1000BASE-T wired LAN device to a wireless LAN device. It supports a wireless LAN communication in the 2.4GHz and 5GHz bands and enables a wired LAN device to join in a wireless LAN environment easily. It also supports enterprise security which allows you to use the Wireless Bridge BR-300AN reliably even in environments such as offices and healthcare sites which require security. This product is not available in North America.
-
Product
Capacitance/Loss Bridge
AH 2550A
-
The AH 2550A offers unparalleled stability, resolution and accuracy in a capacitance/loss bridge (whether manual or automatic). Its numerous state of the art features make it an exceptionally user-friendly instrument, just as was its predecessor, the AH2500A. The precision and ease of use of the AH2550A are creating new applications in science, calibration, and production in a wide range of fields.
-
Product
Coax, Patchcord, ITA, 75 Ohm Coax, 36", RG179U Tan, Single Ended, (3 GHz)
7-381179000-036
Coax Patchcord
Coax, Patchcord, ITA, 75 Ohm Coax, 36", RG179U Tan, Single Ended, (3 GHz)
-
Product
8-Ch, 24-Bit, 25.6kS/s, Quarter Bridge Input IDAQ Module
iDAQ-873
-
High resolution (24-bit)Quarter-bridge supportedSynchronization along with other iDAQ modulesMultiple trigger modes for flexible configured acquisition timingBuilt-in digital filter for higher SNR
