Development Boards
See Also: Development, Software Development, Developers, Test Development
-
Product
Interface Module for the Multimode, Multiprotocol Excalibur 400 Family of Carrier Boards
M4K1553Px(S)
Interface Module
The M4K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M4K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M4K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M4K1553PxS single function (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.
-
Product
PCI To PC104 Extender Board
MS 1717
-
PCI to PC104/EPIC Extender card is used for extending the standard desktop PCI bus to compatible PC104 or EPIC bus. This will help to test all the PC104 cards through standard PC without any embedded processors. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the PC104 or EPIC boards.
-
Product
Meter Qualification Board
MQB
-
Power-up and apply load to electric watt-hour meters for functionality testing with TESCO’s multi-position MQBs. These boards assist with AMI Meter Certification process and AMI meter qualification and communication testing.
-
Product
Compliance Test, Development and Test Service
DinoStor
-
With its focus on solving critical backup problems associated with Network-Attached Storage (NAS), DinoStor delivers a broad range of products and services to benefit users and vendors of NAS solutions.
-
Product
Sensirion SHT31-DIS-B Humidity and Temperature Sensor Breakout Board
SEN-37002-F
-
Breakout board for the Sensirion SHT31-DIS-F with a built-in permeable membrane filter. This sensor is an extremely accurate digital (I2C interface) temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT1x series, and improves upon the success of the SHT2x that came before it. In addition, the SHT31-DIS-B has a wide input voltage range of 2.4V-5.5V and includes temperature isolation and airflow cutouts as recommended for the optimal operation. Finally, in the case of environmental changes that could cause light condensation, the SHT31-DIS-B has a built-in heater to burn off any condensate.
-
Product
Carrier Boards
ROM-DB7501
Carrier Board
ROM-DB7501 is an Referenced Carrier Board designed for Advantech's RISC Qseven 2.0 module. It i provides a thorough environment for module board evaluation with its completefunction support. It also supports 12V power input through AC/DC power adapter and with smart battery design, it's more easier for the end user to design portable devices by referring ROM-DB7501 design.
-
Product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
-
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
Product
Counter/Timer Board
USB-CTR-15
-
The USB-CTR-15 is an ideal solution for adding portable, easy-to-install, counter/timer capabilities to any PC or embedded system with a USB port. This board is packaged in a small, rugged, industrial enclosure and features 15 independent 16-bit counter/timers. The unit is a true USB 2.0 device, offering the highest speed available with the USB bus. It is fully compatible with both USB 1.1 and USB 2.0 ports. The unit is plug-and-play allowing quick connect/disconnect whenever you need additional counter/timer devices on your USB port. The USB-CTR-15 can be used for a wide variety of measurement applications including event counting, frequency measurements, position measurement, pulse counting, pulse-width modulation and pulse generation. The OEM version provides just the board without the enclosure or external screw terminal board and is ideal for a variety of embedded OEM applications.
-
Product
MIL-STD-1553 Four-Channel VME Board
BRD1553VME-4
-
The V-Orchestra™ is a four channel MIL-STD-1553B board, which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability for each channel. V-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 64K word of internal RAM.
-
Product
6U VPX Single Board Computer
VPX6-195
-
Curtiss-Wright Defense Solutions
Our VPX6-195 6U OpenVPX T2080 Single Board Computer (SBC) combines performance with the advanced I/O capabilities of the NXP's quad-core AltiVec enabled T2080 processor. Designed for SWaP-constrained applications, the VPX6-195 provides two independent processor cores on a single printed wiring board (PWB) with a wide range of standard I/O and each with a XMC mezzanine site to provide twice the processing power.
-
Product
Conduction Cooled VPX Interface Board with PCI Express Host Interface
EXC-8000ccVPX
-
The EXC-8000ccVPX is part of the 8000 family of multiprotocol carrier boards. This conduction cooled VPX interface board has a PCI Express host interface and can support up to four independent removable modules and 10 on-board Discrete channels. Each removable module can be any of the 8000 family modules.The EXC-8000ccVPX supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from the board, with much less CPU overhead than when not using DMA.The EXC-8000ccVPX is supplied with C drivers, including source code. Mating connector provided for I/O connection.
-
Product
5 Slot VME64 Portable Tower Development Platform
32V05MMX36N3VCC0
-
Elma Type 32V with superior cooling and accepts 6U cards mounted vertically with or without rear I/O card cage, VITA & IEEE standards, heights are 63HP and 84HP (HP=.2”) and widths 3U, 4U and 6U.
-
Product
High Performance Embedded Development Kit
TySOM EDK
-
The TySOM™ Embedded Development Kit is for the embedded designers who need a high-performance RTL simulator/debugger for their embedded applications such as IoT, Automotive, Factory automation, UAV and Robotics. The kit includes Riviera-PRO™ Advanced Verification Platform and a TySOM development/prototyping board. TySOM boards come with either a Zynq 7000 chip (FPGA + Dual ARM® Cortex™-A9) or with a Zynq® UltraScale+™ MPSoC device. These boards include memories, and various communication and multimedia interfaces in addition to FMC connectors for peripheral expansion. Reference designs for application such as IoT, ADAS, 4K UltraHD imaging and Robotics and a complete reference design, which contains the SW (Linux) and all the hardware blocks required to support the peripherals on the board, are provided.
-
Product
ISA DIO 96 Board
MS 1805
-
*Discrete Input / Output - 96 Channels*All Channels are compatible with 5V TTL / CMOS*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Soft Board Dedicated Automatic Testing Machine
U690FPC
-
1. CCD automatic alignment, the alignment accuracy reaches ± 15μm2. Support layout test, displacement function3. Up and down jig fine adjustment function4. Soft board stretching function5. Automatic marking function
-
Product
CableEye 4-Wire Calibration Verification Board | Cable & Harness Testers
CB52
-
The CB52 is intended for periodic calibration verification of the Kelvin 4-wire resistance measurement module – an optional, add-on module that may be purchased with any new hipot system, or added to an existing high voltage tester as an upgrade.
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24 V
PA1500
-
*16 input channels 24 V, incl. 14 interruptible*16 output channels, 24 V, 500 mA Optical isolation 1000 V*Input and output filters*Watchdog*3 timers/counters
-
Product
Development System
FE-51CC01
-
* Emulates Atmel T89C51CC01/2 and T89C51AC2, T89C5115 * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
Shelf Manager Carrier/Mezzanine Board fix-mounted for CompactPCI
064-754
-
Set of Shelf manager mezzanine board installed on the fix mounted carrier board. The fix mounted carrier board provides all interfaces via headers for easy access and can be used directly inside of your system platform.
-
Product
I/O Input/Output Board
VME-4514A
-
The VME-4514A Analog I/O (AIO) Board provides 16 high-quality analog output channels which can be programmed with on-board jumpers to operate in a variety of voltage ranges. Each output can source or sink 10 mA at ±10 V. For off-line testing, the analog outputs can be disconnected from the I/O connector.
-
Product
Power Interface Board 3U, 1PSU connector
106PIBM301-0000R
-
The PIB 3U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
Isolated Watchdog Board
APCI-035
-
The board ADDIMULTI APCI-035 is equipped with 4 watchdogs allowing the simultaneous monitoring of multiple processes. Watchdog N? 1 works with 2 alarm levels and can be set to 1 of 4 different time bases (µs, ms, s, min). Level 1 alarms the PC cntrol and/or the monitored device. Level 2 resets the PC and/or the monitored device after a defined time. The alarm control can be accessed through 1 trigger channel and 4 different time bases.
-
Product
SparkFun MicroMod Machine Learning Carrier Board
-
The MicroMod Machine Learning Carrier Board combines some of the features of our SparkFun Edge Board and SparkFun Artemis boards, but allows you the freedom to explore with any processor in the MicroMod lineup without the need for a central computer or web connection. Voice recognition, always-on voice commands, gesture, or image recognition are possible with TensorFlow applications. The cloud is impressively powerful but all-the-time connection requires power and connectivity that may not be available. Edge computing handles discrete tasks such as determining if someone said "yes" and responds accordingly. The audio analysis is done on the MicroMod combination rather than on the web. This dramatically reduces costs and complexity while limiting potential data privacy leaks.
-
Product
Board Test Adaptor (BTA)
MS 1104
-
BTA is used to test and validate TARANG (RWR) boards. The BTA has PC interface through RS232 / USB communication port. GUI based Test Software is used to test the UUTs and displays the result.
-
Product
THRU HOLE BARE AND LOADED BOARD TEST PROBES
SERIES 80
-
MAXIMUM CURRENT: 6 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,35 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24 Kt gold plated over nickelBARREL: Nickel silver with 24 Kt goldplated ID and OD over nickelSPRING: (Standard) Beryllium copper,silver plated. (-1) Stainless steel,silver plated
-
Product
TI HDC1080 Humidity and Temperature Sensor Breakout Board
SEN-37001
-
Breakout board for the Texas Instruments HDC1080. This sensor is an extremely accurate temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT2x series, and improves upon the success of the HDC1050. In addition, the HDC1080 has a wide input voltage range of 3V-5V and includes temperature and airflow cutouts as recommended for the best operation. Finally, in the case of environmental changes that could cause light condensation, the HDC1080 has a built-in heater to burn off any condensate. Example code (Arduino platform) is available below.
-
Product
Squid PCI Express Carrier Boards for M.2 SSD Modules
SKU-064-2X
-
Flexible x1 PCI Express to 3 MiniPCI Express Splitter (Splitter) was designed to expand modern motherboard (ATX, mini ATX etc.) that have PCI Express interface. It allows you to connect up to three MiniPCI Express add-in boards to the standard motherboard PCI Express connector.Splitter includes 3 MiniPCI Express adapter boards, x1 PCI Express host board and 3 flat PCI Express Cables.
-
Product
MIL-STD-1553 One-Channel PCI Board
BRD1553PCI-1
-
The P-Orchestra™ is a one-channel MIL-STD-1553B PCI board, which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability. The board can be used as a hardware and software development kit for IP cores. P-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 16K word of internal RAM.
-
Product
Sensirion SHT31-DIS-B Humidity and Temperature Sensor Breakout Board
SEN-37002-H
-
Breakout board for the Sensirion SHT31-DIS-B. This sensor is an extremely accurate digital (I2C interface) temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT1x series, and improves upon the success of the SHT2x that came before it. In addition, the SHT31-DIS-B has a wide input voltage range of 2.4V-5.5V and includes temperature isolation and airflow cutouts as recommended for the optimal operation. Finally, in the case of environmental changes that could cause light condensation, the SHT31-DIS-B has a built-in heater to burn off any condensate.
-
Product
Thunderbolt V-600 Board 8-Slot
-
The 6U VME Thunderbolt boards provide optimal performance and reliability. The Thunderbolt V-600, configured with one Compute Module of four MPC7410 processors, provides 16 GFLOPS of computational performance per 6U VME slot. Data is transferred throughout the Thunderbolt over the SKYchannel Packet Bus. Data moves transparently through the SKYchannel P2 interface to other boards in a SKYchannel chassis.
