Development Boards
See Also: Development, Software Development, Developers, Test Development
-
Product
PCI Express A/D Board
AD16-250 - Dual/Quad 16 bit, 250 MS/s
-
The AD16-250 series has two or four 250 MS/sec 16-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at over 1 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual and quad channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, providing up to four (4) times the effective memory depth.
-
Product
PC/104 Analog Output Board
104-AO12-4
-
The following functions are available in many configurations giving the user the ability to specify exactly what’s needed. Interrupts are individually or globally enabled or disabled via software. A status register is provided to determine the interrupt source.
-
Product
Clock And Trigger Synchronization Board With Atomic Clock
CLKSYNC-PCI-AC
-
CLKSYNC-PCI-AC is a clock and trigger distribution board designed to provide up to eight synchronous clock and trigger outputs. The CLKSYNC-PCI-AC is designed for use with multi-channel, ADC and DAC systems where precise clock and trigger synchronization are required.
-
Product
Sensor Board for micro:bit
-
The MonkMakes Sensor Board for micro:bit allows you to sense sound level, temperature and light level. You can connect it up to your micro:bit using alligator clips.
-
Product
6U OpenVPX Multi-function I/O Board
67C3
Multifunction I/O
NAI's 67C3 is a 6U OpenVPX Multi-function I/O and Communication Board with six function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24V, LACQUERED
APCI-1500-LAC
-
PCI interface to the 32-bit data busConnector compatible to PA 1500Connector and software compatible to CPCI-150016 isolated input channels, 24 V, including 14 interruptible3 software-programmable counters/ timers16 isolated output channels, 10 to 36 V, output current 500 mATimer-programmable watchdog for the reset of the outputs to ??Diagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdogInterrupt triggered through watchdog, timer, errorOne ground line for all inputs and one ground line for all outputs
-
Product
PXI Express Board Virtex-5 ADC Module
SMT742
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
3U VPX PMC/XMC Carrier Board
IC-CMC-VPX3b
-
The IC-CMC-VPX3b is a carrier board designed to expand 3U VPX system capabilities with the integration of PMC/XMC mezzanines.
-
Product
Development Kit
-
The VP430 is 3U VPX RF processing system featuring the transformational Xilinx® Zynq® Ultrascale+™ RF system-on-chip technology (RFSoC). The ZU27DR device used on the VP430 includes eight integrated analog-to-digital converters at 4GSPS, eight digital-to-analog converters at 6.4 GSPS, a user-programmable FPGA fabric, and multi-core Zynq ARM® processing subsystem.
-
Product
ISI Channel Boards
M8049A
-
The M8049A ISI channel boards can be used to emulate channel loss in receiver test setups. The boards are used to emulate channel loss for data rates of 32 Gb/s and higher. A choice of 21 PC board traces with different lengths can be inserted into the signal path. The trace lengths range from 0.8 inch (20.3 mm) to 22.3 inch (566.4 mm). By cascading the traces within one board or with another board, a wide range of channels can be emulated with very fine resolution of insertion loss steps. With their small size the ISI channel boards can be located closely to the device under test.
-
Product
Warm-Up Board
WECO 9000
-
The WECO 9000 Warm-Up Board from Radian Research provides a safe, easy to use, affordable solution to your AMI meter functional testing. The WECO 9000 originated as part of RADIAN Innovate™ Custom Design Solutions. Numerous process improvement workshops RADIAN facilitated at electric utilities have shown us that meter shops are experiencing as low as 65% pass yield on AMI meter testing. This means almost half the meters arriving are transported through the testing process and not ready for accuracy testing. Typical failures include inoperable display, diagnostic errors, disconnect switch in an open state, wrong firmware version, and inability to register on the communications network.
-
Product
Breakout Boards
Micro D
-
Micro D Breakout Boards are also open designs providing signal access for the popular MicroD series of connectors. Breakout boards incorporate one male and one female connectors.Micro D Type: 9, 15, 21, 25, 31, 37, 51 and 100 positions
-
Product
HUSKIE 2.0 roboRIO MXP Expansion Board
FRC3061-MXP2-R1
-
The Huskie Board, designed by FRC Team 3061, is an FRC qualified expansion board for the NI roboRIO robotics controller. In addition to breaking out all available signals on the MXP expansion port, this board uses a Parallax Propeller IC (8 symmetrical logical cores with shared memory and peripheral access) to enable tasks such as advanced data logging, on-field driver control and status, and NeoPixel control. Additional GPIO and analog inputs are added with open source code to allow further customization.
-
Product
FlexRIO Adapter Module Development Kit for Modular I/O
780711-01
Module
FlexRIO Adapter Module Development Kit for FlexRIO—The FlexRIO Adapter Module Development Kit (MDK) for Modular I/O enables you to choose the specific converters, buffers, connectors, and other components so that you can build the exact analog and digital I/O you need into a custom adapter module for FlexRIO. NI recommends that you have custom printed circuit board (PCB) design and hardware description language (HDL) code development experience to use the FlexRIO Adapter MDK for Modular I/O.
-
Product
Desktop Meter Qualification Board
2199
-
Providing complete capabilities for evaluating meters and communications performance, TESCO’s Desktop Meter Qualification Board (Catalog No. 2199) can generate any voltage and load conditions the meter may encounter in the field. Apply non-sinusoidal voltages with complex load waveforms. Perform disconnect tests and reconnect tests without having to worry about being able to drive the meter’s switches.
-
Product
3U VPX UltraScale Kintex FPGA Carrier Board With FMC+ Site
VPU: 085/115
-
The VPU utilizes the AMD Kintex UltraScale XCKU085 or XCKU115 FPGA as options. The Kintex UltraScale FPGA family delivers impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed-point and repetitive processing tasks.
-
Product
LVDS To DVI-D Converter Board
AX93221
-
*Input supports 18/36/24/48-bit LVDS through 40-pin LVDS connector*Output supports DVI-D connector*Size: 60 x 50 mm*Applied for PICO821 and PICO822
-
Product
Hall Sensor Board with I2C Interface
046-322
-
Version: +5V/15A +12V/5A -5V/15A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Ethernet to Relay Interface Boards
Model 8064 OEM
-
* 115631-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional terminal board for easy connections without soldering. See the Ethernet Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS Wiring Kit to connect to an RJ45 connector on the rear panel.
-
Product
Microcontroller Development Kit
MDK-ARM
-
The MDK-ARM is a complete software development environment for Cortex-M, Cortex-R4, ARM7 and ARM9 processor-based devices. MDK-ARM is specifically designed for microcontroller applications, it is easy to learn and use, yet powerful enough for the most demanding embedded applications.
-
Product
OpenVPX Boards
-
Configuring OpenVPX systems can be tricky. Utilize Pixus' expertise in selecting the right VPX modules for your application. With our key partnership, Pixus can help you find the right boards at the right price. For simplicity, you can order your full OpenVPX system and boards through Pixus or we will refer you to the best fit for your application. Our flexible approach leaves the choice to you, and helps ensure you are getting the best performance and value required for your system.
-
Product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, RS-422 Inputs
APCIE-1711
-
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied software. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed and reconfigured as further requirements arise.
-
Product
Integrated Board Power Management Functions For The Forward Thinking Engineer
Power Manager II
-
*Up to 12 differential voltage sensors with immunity to noise on ground plane*Voltage trimming to within 1%*Ruggedized CPLD with up to 48 macrocells for sequencing and supervisory signal logic*Large operating power supply range (3.3 V + 20% to 3.3 V -15%)*Up to 4 High-Voltage MOSFET Driver Outputs*Voltage Measurement with 10-bit ADC through I2C*Up to 8 On-chip DACs for Margining and Trimming
-
Product
Power Interface Board 6U, 1 PSU connector with AC pins
106PIBM601-9001R
-
The PIB 6U 1 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
Cross Development Tools
68HC12 and HCS12
-
Cosmic's toolchain for the 68HC12/HCS12 family is part of a complete and uniform product line incorporating over 20 years of innovative design and development. Cosmic's familiar and easy to use software interface is available for all Freescale microcontrollers to simplify the migration between targets. All Cosmic products include one year of technical support and updates.
-
Product
Electronical Load Board 6U CompactPCI (air cooled)
056-169
-
The 6U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
Product
Interface Board, 8:1 USB
40-965-903
Interface
Converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 8 USB type A and 1 USB type B connectors. Allows the multiplexing of up to 8 USB1 or USB2 signals.
-
Product
PCI Data Acquisition Boards
AD8-1250DMA Series - 8 bit, 1.25 GS/s
-
Model AD8-1250DMA contains a 1.25 gigasample/second 8 bit A/D, 8 GB of on-board SDRAM memory and the ability to transfer data directly into the computer system's memory at up to 320 MB/s on 64-bit PCI systems.
-
Product
FPGA DSP Board
-
Renice has developed part of the FPGA evaluation board, which can be used as high-speed signal processing board, wireless communication board and image processing board. By default, it’s equipped with Altera FPGA (StratixIV), high-speed ADC/DAC, USB Controller and SODIMM Connector.
-
Product
PCI Bus Analog Output Board, 4 Isolated Outputs, 14 Bit
APCI-3501-4
-
4 analog output channels Optical isolation 500 V Settling time 30 µs typ. 14-bit resolution (13 bit for 0-10 V) Output voltage: ±10 V, 0-10 V (switchable through software) Output voltage after reset: 0 V Each output channel has its own ground line (without optical isolation from the others) Driver capacity: 5 mA/500 pF Short-circuit protection, EMI filters Noise neutralization of the PC supply Creeping distance: 3.2 mm acc. to DIN VDE 0411-100 Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary2 digital input channels, 24 V, isolated 2 digital output channels, 24 V, isolated Noise immunity Test level: ESD: 4 kV Fields: 10 V/m Burst: 4 kV Cond. radio interferences: 10 V
