In-circuit Testers
See Also: In-circuit, Incircuit, In-Circuit Debuggers, In-circuit Emulators, In-circuit Probes, In-Circuit Test, In-circuit Test Systems
-
Product
Transmission & Synchronization Tester
xGenius
-
xGenius is a nice handheld tester equipped with a large (8 inc) capacitive touch-screen to make easier the analysis and results interpretation. It is 100% suitable for labs or field use because is full equipped (IP/Ethernet/PTP/T1/E1), battery operated, light (1.9kg) and very rugged. The unit is able to test Ethernet/IP networks up to 10Gb/s while supporting master/slave Sync-E/PTP emulation and also has interfaces for T1/E1.
-
Product
P-GW Functional Tester
-
The LTE PGW Functional Tester provides a wrap-around test solution for the Packet Date Network Gateway by emulating all the LTE network elements surrounding the PDN-GW (System Under Test). The P-GW Functional Tester emulates LTE Core Network entities such as the S-GW, PCRF, OCS and OFCS. It tests the S5/S8, S7/Gx, Gy and Gz interfaces of the P-GW.
-
Product
Network Transmission Tester
SIGNALTEK NT
-
If you install, maintain or troubleshoot data cabling and Ethernet networks, SignalTEK NT allows you to prove the performance up to Gigabit Ethernet transmission rates.
-
Product
Rail Pressure Tester
RPT-5
-
The RPT-5 device is used for performing an independent, parallel pressure measurement in storage fuel systems such as Common Rail (Diesel) and GDI/FSI (petrol). The tester, apart from pressure value, also diagnoses power supply of a sensor. Additional advantage is the capability of automatically detecting the terminals of the sensor, which is useful especially when using needle probes.
-
Product
Earth Ground Tester
1625-2
-
The Fluke 1625-2 earth ground tester measures earth ground loop resistances using only clamps, only stakes, or one clamp and stakes. With the stakeless test method, the Fluke 1625-2 is able to measure earth ground loop resistances for multi-grounded systems using only current clamps. This technique eliminates the dangerous, and time consuming job of disconnecting parallel grounds, and finding suitable locations for auxiliary ground stakes.
-
Product
High-Low Circuit Tester
29500
-
The low-side checks AC and DC current up to 28 volts with power on. The high-side checks spark plug wires without piercing. Complete with insulated clip.
-
Product
Comparison Testers
GCL Series
-
Nagman Instruments & Electronics Pvt. Ltd
Budget Solutions. Very Low Maintenance Cost. Compact & Easy to carry for Lab & Field use. Priming Pump with Fine Adjustment Vernier Incremental Pressure generation. Adjustable Foot.
-
-
Product
Digital Deadweight Tester
PIT-5000
-
The PIT5000 is the modern tool for conducting pipeline hydrostatic tests. Replace your dead weight testers, pressure chart recorders and temperature chart recorders with the convenience of digital data collection and user friendly PC software. Pressure, ambient temperature and pipeline temperature are measured by the system's NIST traceable instrumentation and plotted on one graph versus time.
-
Product
Digital Motor Testers
-
Time to replace ALL your Motor testers with ONE SAMATIC. The best 10-in-1 Digital Motor Tester on the market- is also amazingly packaged in a portable case. Your operation should have the best Motor Testers on the world Market- The SAMATIC 12500R or SAMATIC 6000R
-
Product
Other Testers
-
Logic Probe, Digital Pulser, Voltage Tester, Circuit Tester, Analog Type Battery Tester.
-
Product
In-Circuit Test (ICT) Fixtures
Test Fixture
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
Product
Digital LOOP/PSC/LOAD Tester
2811 LP
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Displays and sound warning if external voltage present.● Displays mains voltage, scroll trough menus.● Checks wiring integrity (LEDs and display).● Single button operation.● Auto-off/auto-ranging.● Combined prospective short circuit current, PSC and LOOP tester.● Built-in carry case, test leads in separate pouch.● Loop test for L-E and L-N and PSC.● Voltage test L-N and L-E.● Enables analysis of constituent components in L-E and L-N loops giving resistance of earth, neutral wire, live wire and transformer winding.● Display can be customized for special orders.● 60Hz available on request.
-
Product
Medical Masks Flammability Tester
TF361
-
TESTEX Testing Equipment Systems Ltd.
Medical Masks Flammability Tester is used to test the flammability of medical masks, to ensure the safety of masks to wear in. Medical Masks Flammability test Chamber complies with EN 149, GB 2626, GB 19083.
-
Product
Friction & Peel Strength Tester
FPT-F1
-
FPT-F1 Friction Peel Tester can be used to test coefficient of static and dynamic friction of plastic films, sheets, foils, paper, cardboard, woven bags, fabric (fabric style test), metal-plastic composite belt for communication cable, convey belt and textile, as well as peel strength of adhesive laminated products, medical adhesive bandage, release paper and protective films.
-
Product
Multifunction Tester
EASYTEST
-
EASYTEST carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Telephone, Exchange & DSLAM Tester
ETET 30
-
Exchange, Line, Phone, ADSL/VDSL DSAM test, Modem detection.
-
Product
Rope Testers
-
The LMA Signal measures loss of metallic cross-sectional area (LMA) caused by corrosion, abrasion, etc. The LMA Signal is quantitative and can be calibrated. (Typically, a rope must be retired when the LMA exceeds 10%).The WRR Signal measures wire rope roughness (WRR). WRR is defined as the aggregate surface roughness of all wires in a rope. WRR is typically caused by and indicates internal and external corrosion pitting, broken wires and clusters of broken wires. The WRR signal is quantitative, and it is calibrated together with the LMA Signal.The LF Signal can indicate localized flaws (LF), for example, broken wires, corrosion pitting, etc. Because it is only qualitative - and cannot be calibrated - it is of limited value for assessing rope deterioration and for making rope retirement decisions.
-
Product
Electrical Tester
T5-600
-
The T5-600 Electrical Tester is a versatile troubleshooting tool you can carry to every job site. Use it to check voltage, continuity, and current, all with one compact, rugged tool. Just select volts, ohms, or current and the tester does the rest. For higher voltage applications check out the Fluke T5-1000.
-
Product
Doide Testers
-
Specialized test for Axial, SMD and 2-pin package type.Electrical Testing: Forward：VF Reverse：VZ、DVZ、IR、ACIR、DIRFour-wire measurement and contact resistance in case of deviation.Manual test or conjunction with automatic machine.
-
Product
2Mbit/E1 Error Rate Tester
CA6037
-
CA6037 is a hand-held equipment designed for 2M bit erroe rate test, applicable to telecommunication access networks, transmission networks and the start-up, check and maintenance of optical communications systems.
-
Product
EYE Super Xenon Tester
-
Xenon Tester is the standard climatic wear testing device under domestic and international standards such as ISO, JIS, and ASTM as its light source achieves spectral energy distribution that approximates sunlight which has high correlation to natural outdoor exposure.
-
Product
Martindale Abrasion Tester
GT-KC13A
-
To determine the abrasion resistance of all kinds of footwear vamp material. Samples are rubbed against known abrasion at low pressures and in continuously changing directions and the amount of abrasion. The unique design allows removal of individual sample holders for examination without lifting the top motion plate.
-
Product
Fuel Injection Tester
FIT13APB
-
This basic fuel injection tester includes large and small Schrader adapters, M6-1.00 O-ring adapter, and tee manifoldIncludes everything necessary to test the following systems: American Motors; Bosch AFC, MPC European and Japanese (except CIS- use our FIT447); Chrysler Corporation; Ford Motor Company; GM (except TBI- use our FIT446)
-
Product
Load Tester for A Type dDrometers
-
A load tester for checking the spring load characteristics of ASKER hardness testers at the hardness readings of 25, 50, and 75.It is necessary to check the shape and height of the indentor, the indicating mechanism, and other parts of the hardness tester are set correctly before doing a load test. This tester is applicable to "quasi-object"models with spring load characteristics slightly different from that of object models by adjusting the reference value accordingly.
-
Product
Suspension/Road Contact Tester
VLT3673-G6
-
The VLT 3673-G6 suspension / road contact testers operate according to the well-known EUSAMA principle. However, the diagnostic options are not restricted to the contents of this specification. In addition to the usual road contact values, the following values are also measured and displayed: the contact value difference, resonance frequency and wheel weight at minimum contact value, tyre rigidity, wheel weight and axle weight. There is a general final evaluation so that all these values do not have to be interpreted after every test.
-
Product
Leak Testers
-
Uson provides automatic non-destructive air leak and flow measurement equipment and solutions used in product development and manufacturing environments for medical device, automotive, electric vehicle battery, packaging and industrial applications. Uson leak testers are highly configurable and are built with premium components ensuring maximum quality, reliability and performance.
-
Product
Harmonics and Flicker Testers
-
complied standards and features of the KHA1000 (dedicated for single phase), is equipped for the harmonic and flicker compliance test exceeding 16A of the single-phase and three-phase equipment. With this unit alone, you can take highly accurate simultaneous three-phase measurements up to 40A/phase*.
-
Product
Single-functional testers
3110
-
The MI 3110 EurotestIM is a perfect tool for testing of permanent integrated or portable Low Voltage Electrical Installa-tions supplied by Generator or Transformer and protected by an IT earthing system. Designed for simple but efficient safety testing of Integrated IT Earthing System powered with LV Generator or Transformer! With a single, pre-programmed AUTO SEQUENCE® with sub-tests and adjustable limits it is possible to perform all the necessary verifications of safety limits of a specific LV IT installation.
-
