POT
Measure the voltage in a circuit or function as voltage dividers.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
-
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Hi Pot Meters
-
The HI Pot Device is designed to Hi Pot de-energized 15kV class cables. The tool transforms 18 Volts from the battery to approximately 8,000 volts DC. When the battery is installed and the safety switch is in the closed down position, the unit is in voltage detection mode. The unit should be in this position when installing the device, as it will sound a warning alarm if you approach an energized source. When the safety switch is lifted and the toggle switch is switched up, the unit is in the Hi-Pot mode and the high voltage DC is being applied.
-
Product
50 Ohm Bridge / Freq Counter
-
* Generates a 3 to 30 MHz low level signal displayed on small 8 x 2 LCD * 50 ohm bridge supports tuning 50 ohm antennas * Adjust POT to find the resonate frequency of antenna * 30 turn POT allows easy smooth frequency adjustment * Bright red LED extinguishes when bridge is balanced * Function switching allows for use as frequency counter * 50 ohm termination included * measures 5.5 x 2.5 x 1.1 inches * 9 volt battery operation
-
Product
UV Sensors
-
The patented domed shaped sensor head facilitates runoff of dew and rain, helping to keep the detector clean and minimizing errors caused by dust blocking the radiation path. Sensors are housed in a rugged anodized aluminum body and electronics are fully potted.
-
Product
Time Code Distributor/Reshaper
SR-112
-
Like it’s big brother the SR-112 Distripalyzer, the SR-28 can drive time code over long cables, making it ideal for synchronization during live shows and remote recording. The SR-28 time code distributor, with two inputs and eight outputs, reshapes time code while distributing it, eliminating amplitude distortions and level fluctuations. The level of each output is individually adjustable via front panel pots. The input is selected via a front panel switch. Also included are 2 power inputs and an automatic switch over in case of failure.
-
Product
Remote Slab Sensor and Outdoor Temperature Sensor
CHV-RSS
-
The CHV-RSS is a remote temperature sensor designed for use with select Crestron thermostats. Ideally suited for concrete slab, under floor, or any outdoor installation, the CHV-RSS is an extremely accurate temperature sensor potted within a rugged waterproof stainless steel sleeve.
-
Product
Limit Alarms
-
Process limit alarms monitor sensor or process current input signals and trip a relay output if the input exceeds a user-defined hi/lo setpoint limit. Select from AC-, DC, and loop-powered models. Configuration is easy with Windows software, push-buttons, switches, or pots for settings depending on the series.
-
Product
Reliability Testing Services
-
Innovative Circuits Engineering, inc
Our Reliability Testing Services make it possible for us to work with many different customers who manufacture devices that need tests such as pressure pot, temp cycle and more.The focus of our reliability testing lab is to provide our customers with an array of services and tests that fulfill all of their reliability testing needs. Whether you need preconditioning, thermal shock, pressure pot, or many other reliability testing needs, we are happy to be of service.
-
Product
Precision Pots Multiturn
-
Precision potentiometers are designed for control applications where accuracy and high-reliability is important. These devices are available in conductive plastic, wirewound or Hybritron® element types, and in various sizes. Both single-turn and multiturn models are available. Typical applications include measuring linear distance, angles or rotations in production equipment, industrial test and measurement equipment, and medical equipment.
-
Product
Precision Pots Single-turn
-
Precision potentiometers are designed for control applications where accuracy and high-reliability is important. Theses devices are available in conductive plastic, wirewound or Hybritron® element types, and in various sizes. Both single-turn and multiturn models are available.
-
Product
SparkFun OpAmp Breakout
LMV358
-
This is a simple 5V Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets the signal level between the stages, not the feedback path. The bandwidth is set to 15.9kHz by a pair of feedback capacitors, or over 100kHz with the caps removed. The LMV358 opamp can source up to 160mA and works well as a low impedance driver/buffer.
-
Product
IO-Link Hubs
-
- For the simple connection of binary sensors to any IO-Link master- Uses industry standard M12 unshielded patchcords- Clearly visible LEDs for displaying operation, switching status and error- Robust design with full potting for use in harsh industrial environments- Robust M12 connectors for connecting sensors and actuators
-
Product
DCDC
FC Series
-
The FC Series are ultra-low noise, high performance DC/DC converters that are packaged in low profile (0.4 inch high) cases. Essential quality performance features are designed and built-in. A high performance Pi input filter minimizes input reflected ripple, while 5-sided electrostatic shielding and tape-wound toroids, rather than pot cores, minimizeradiated EMI. Advanced circuit design techniques reduce conducted output noise in the form of current spikes, to an extremely low level.
-
Product
Programmable Hi-Pot Tester
DU331/332/333
-
Delta United Instrument Co., Ltd.
Large LCD Display Window for Setups and Test Values Output Frequency 50/60 HZ SelectableAll Initial Default Function Setting scan be Changed Easily to Fit RequirementEasy Manual Driven with Cursor Guiding Operation Mode Battery Backup Function will Recall theTest Parameter Settings before Power offLarge Memory (100 sets) for Setup Steps & ParametersEach Memory offers 9 steps of different Test ParametersTest mode: Single Step, Multiple Steps (Step by Step), Test Circle Number or Continuous Test are Programmable DU333 is designed for Multi-point Scan Test DU331/DU332 can perform Multi - point Test when used with Scan Box DU330
-
Product
Signal Conditioning & Control
-
Offering a wide variety of products from amplifiers and comparators to redrivers, microcontrollers, data converters (ADC) and digital potentiometers (POTs).
-
Product
COMPUTERIZED LCRTZ TEST SYSTEM (Automatic Transformer Test System)
CVCT-S20
-
Ideal for fast and fool proof testing of COILS AND SMALL TRANSFORMERS like SMPS transformers, Telecom transformers (HYBRID, POT CORE, RM-CORE), Pulse transformers etc. The systems scans at one stroke, all the windings of a transformer and tests as per definition of test procedure. The test procedure can be pre-programmed and stored under User friendly menu driven software . Any semi-skilled and unskilled person can be engaged for actual testing purpose. Can Select test frequency, pin number, parameters, test conditions, limits for each test. Test any pin to any other pin any defined parameter.Test Parameters :-> Inductance-> Capacitance-> AC Resistance, -> DC Resistance, -> Impedance, -> Leakage Inductance,-> Transformation Ratio & Winding PolaritySPECIFICATIONS :Measurement Frequencies : 50 Hz, 100 Hz, 500 Hz, 800 Hz; 1 KHz, 2 KHz, 5 KHz, 10 KHz. Measurement Voltage: 0.1 V – 1.0 V RMS adjustable under program control.
-
Product
Curing Systems
-
Manufacturers know that the coating, dispensing and/or potting process doesn't end once the material is applied. Most materials require some sort of finishing step, or cure force, to dry, harden or cure the coating. For those materials that require thermal or UV cure forces, SCS manufacturers cure systems that are robust, reliable and ensure that your process is as efficient as possible.
-
Product
Neon Transmitter
-
Shanghai Yiya Electronic Instrument Co., Ltd.
Asphalt resin filled and vacuum potted. Patented magnetic core at low consumption. Heavey duty metal box and coated power. User Friendly-Adapts to most grounding situations.
-
Product
DC Electronic Load
EE15140A
-
The EE15140A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices
-
Product
Back Plane Tester
-
This machine is used to test back planes used in telecommunications central stations. An operator loads a completed point to point wired back plane onto a retractable shelf on the front of the tester. Table continues and the disk falls through a hole into the bin. The shelf is pushed back into the machine where it is held in place by pneumatic operated clamps. Then a series of pneumatic cylinders sequentially insert a test card into each location in the back plane. A remote instrument performs a complete point to point continuity, short and hi pot test on all connections in the back plane.
-
Product
Variable Tone Generator
-
> 60 Hz to 18 kHz approx> 1.3 VAC P/P> Frequency & Level Pots> Sine or Square Wave> 4.5 x 2.5 x 1.1 inches> 9 volt battery operation
-
Product
Time Code Reshaper/ Distributor
SR-28
-
The SR-28 can drive time code over long cables, making it ideal for synchronization during live shows and remote recording. The SR-28 time code distributor, with two inputs and eight outputs, reshapes time code while distributing it, eliminating amplitude distortions and level fluctuations. The level of each output is individually adjustable via front panel pots. The input is selected via a front panel switch. Also included are 2 power inputs and an automatic switch over in case of failure.
-
Product
Hi-Pot Tester
DU3315A/3316A
-
Delta United Instrument Co., Ltd.
Real-time Open Check of the alarm and signal output of no contact signal3 in 1 tester with AC, DC, IR functions ( IR function is optional for DU3316 only)ARC Detction:DU3315A /DU3316A Standard function40 x 4 LCD text displayFast cut-off time : 0.4ms5 sets of memory, 3 steps for each memory
-
Product
DC Electronic Load
EE30141A
-
The EE30141A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices
-
Product
Hi-Pot Testing
-
The CableEye HVX System combines our M3U tester with a high voltage module to provide Hi-Pot testing of insulation resistance and dielectric breakdown up to 1500Vdc and 1000Vac.
-
Product
On-stream Analyzer
Boxray Flowstand
-
Our secondary sampling tanks, Boxray Flowstand, are fully automatic and are used with both the on-stream analyzers Boxray 24 and Boxray Compact. In addition to the streams being screened and flowing down to the analyzer, daily composite samples are collected. These composite samples flow down to special containers (pots) with perforated bottoms, where the water is drained from the samples, which makes work fast and effective for lab personnel.
-
Product
AC DC Withstand Voltage & Insulation Tester (HI-POT)
SS71XX series
-
High voltage withstand and insulation tester (HI-POT tester) is used for testing insulation grade and withstanding voltage capability of electrical equipment, transformers, motor, relays, cables, electronic components, electronic applications, inductors, ignition coils, insulation wires, insulation tapes, valve coils, reactors, contactors, etc.
-
Product
HDMI Audio Extractor with Audio Amplifier, RS-232 and IP Control
EMX-I-AMP
-
The EMX-AMP is a 4K HDMI Audio Extractor with built-in 50 watt audio amplifier for direct connection of 8 ohm speakers. The device also provides line-level stereo Aux audio input and allows audio mixing of HDMI audio with the Aux input. Volume can be controlled from the front panel, RS-232, or external digital rotary pot (encoder) that can be mounted on a wall-plate.
-
Product
Receiver Semi-Kit
75-NS-3
-
National RF’s 75-NS-3 receiver is a complete super-hetrodyne mini high frequency receiver, designed specifically for the short-wave listener, electronics enthusiast or radio amateur, who wants to use their hands and build a radio. The receiver is offered as a semi-kit in which the electronic assembly is loaded and functionally tested at the National RF facility. The customer must then go to the grocery store (yes…the grocery store!), procure a can of lunch meat, eat it or give it to the dog, and then proceed to drill and paint the can, in order for it to become the receiver’s enclosure! As the name of the preferred potted meat can has a registered trademark by Hormel Foods, Inc., it won’t be mentioned on this web-site. However, the name of the product is synonymous with unwanted email!!! In addition, there are other food products that might be found that are packaged in the same metallic enclosure. Detailed drilling instructions and final assembly instructions are provided as part of the kit. All other parts required for completion of the receiver are provided as well. Recognizing that the finished assembly looked somewhat like the fabled Collins receiver of the ‘60s, the 75S-3, (particularly when the can is painted a light gray) National RF engineers dubbed it (with tongue firmly planted in cheek, of course) the 75-NS-3! Although we have had fun packaging this receiver in a lunch meat can, it is nothing to turn your nose at! Its performance and portability will surprise you, and it is an ideal radio to bring with you on any trip!
-
Product
Radiographic Inspection Test
-
The radiographic inspection is a non-destructive x-ray method for detecting internal physical defects in small component parts which are not otherwise visible. Radiographic techniques are intended to reveal such flaws as improper positioning of elements, voids in encapsulating or potting compounds, inhomogeneities in materials, presence of foreign materials, broken elements, etc.
